Search NASA⌕ Search

Engineering topics

Watkins, Thomas R.

Publications and source records attributed to Watkins, Thomas R..

16 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Oil-Pressure Based Apparatus for In-Situ High-Energy Synchrotron X-Ray Diffraction Studies During Biaxial Deformation

Background: Understanding biaxial loading response at the microstructural level is crucial in helping better design sheet manufacturing processes and calibrate/validate material deformation models. Objective: The objective of this work was to develop a low-cost testing apparatus to probe, with sufficient spatial resolution, the micro-mechanical response of a sheet material in-situ under biaxial loading conditions. Methods: The testing apparatus fabricated as a part of this study operates in a similar fashion to a standard bulge test and uses oil pressure to generate biaxial loading conditions. This biaxial testing apparatus was operated within a synchrotron beamline to characterize the mechanical response of a flash-processed steel sheet using in-situ high-energy X-ray diffraction (XRD) measurements. Further, the GSAS-II package was utilized to develop a workflow for the analysis of the large volume of diffraction data acquired. The workflow was then used to extract the peak position, width, and integrated intensity of the XRD peaks corresponding to the major body-centered cubic phase. Results: The equi-biaxial nature of the loading in the measured area was independently corroborated using experimental (XRD) and simulation (finite element analysis) methods. Furthermore, we discuss the evolution of elastic strain in the major body-centered cubic phase as a function of applied oil pressure and location on the steel sheet. Conclusions: A key advantage of the biaxial apparatus fabricated in this synchrotron study is demonstrated using the results obtained for the flash-processed steel sheet – i.e., mapping the lattice plane-dependent response to biaxial loading for a relatively large sample area in a spatially resolved manner.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Mechanisms for high creep resistance in alumina forming austenitic (AFA) alloys

Castable alumina forming austenitic (AFA) alloys have demonstrated superior creep life and oxidation resistance at temperatures exceeding 800⁰C. Despite the success in the applicability of these alloys in extreme environments, there is a limited understanding of the deformation modes and the influence of each alloying element guiding the alloy design strategies that could further enhance the creep strength of these AFA alloys, particularly at temperatures at and above 900⁰C. In this study, we reveal the mechanism underpinning the superior creep performance of castable AFA alloys that involves suppressing primary carbide formation through minor compositional modification. This approach results in a three-fold increase in creep strength at 900⁰C and 50 MPa. Here, by employing integrated characterization techniques, we analyzed the microstructures of two AFA alloys, both before and after the creep process. We discovered that the suppression of primary carbides permits the in-situ clustering of now-available interstitial elements such as C, Si, and O during high-temperature creep. This improved solid solution strengthening and reduced stacking fault energy of the alloy. Moreover, it also enabled controlled secondary carbide formation during testing, further improving the creep resistance. These findings underline the important interplay between alloy composition, microstructure, and creep properties, and offer a promising design strategy for developing economical high-temperature Fe-based alloys suitable for advanced applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Infrared thermometry in high temperature materials processing: influence of liquid water and steam

Here, the capability of four infrared thermometry techniques (2-colour and 1-colour pyrometers, Pyrolaser and IR camera) was evaluated with respect to the impact of water or steam in the line of sight to determine temperature from two heat sources (blackbody calibration source and steel block inside the furnace). The influence of liquid water on the temperature readings was minimal when using 2-colour pyrometry due to comparable absorption coefficients of water for the measured wavelengths. The signals measured using both the Pyrolaser and the 1-colour pyrometer were decreased due to the partial absorption and resulted in an apparent temperature lower than the actual. Water readily absorbed the IR signal in the range of the IR camera operation, resulting in no signal whenever liquid water was present in the line of sight. Steam caused the most deviation and fluctuation of temperature readings for all techniques due to the large level of light scattering in addition to the absorption of the radiant energy. A technique was developed to determine the transmissivity (apparent emissivity) when water or steam is in the line of sight of measurement. An approximate correction to the measurements based on Planck’s law is discussed for both 2-colour and 1-colour pyrometers.

2-colour and 1-colour pyrometry↗
DOE OSTI2023

3D Printed eutectic aluminum alloy has facility for site-specific properties

Additive manufacturing (AM) has the ability to print structures with site-specific properties. Existing AM approaches for site-specific properties are, however, based on complex processing-microstructure relationships in conventional alloys that were not designed for this purpose. Here, in this work, we report a straightforward approach for achieving site-specific properties that takes advantage of eutectic solidification characteristics. We demonstrate that the yield strength of a eutectic Al-Cu-Ce-Zr alloy can be tuned by varying the laser scan speed in concert with hatch spacing in laser powder bed fusion AM. A faster speed increases solidification rate resulting in finer eutectic spacing and higher strength. The hatch spacing is reduced at faster speeds to ensure overlap between melt pools which become smaller with increasing scan speed. The yield strength and its anisotropy relative to build direction are further tunable with a heat treatment. The scan speed-eutectic spacing-strength relationship is successfully applied to print a complex pattern of site-specific hardness in the alloy. The generalized principle of using AM for a eutectic alloy to create site-specific properties and anisotropy in properties is demonstrated.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Robust Copper-Based Nanosponge Architecture Decorated by Ruthenium with Enhanced Electrocatalytic Performance for Ambient Nitrogen Reduction to Ammonia

Electrochemical conversion of nitrogen to green ammonia is an attractive alternative to the Haber–Bosch process. However, it is currently bottlenecked by the lack of highly efficient electrocatalysts to drive the sluggish nitrogen reduction reaction (N2RR). In this work, we strategically design a cost-effective bimetallic Ru–Cu mixture catalyst in a nanosponge (NS) architecture via a rapid and facile method. The porous NS mixture catalysts exhibit a large electrochemical active surface area and enhanced specific activity arising from the charge redistribution for improved activation and adsorption of the activated nitrogen species. Benefiting from the synergistic effect of the Cu constituent on morphology decoration and thermodynamic suppression of the competing hydrogen evolution reaction, the optimized Ru 0.15 Cu 0.85 NS catalyst presents an impressive N 2 RR performance with an ammonia yield rate of 26.25 μg h –1 mg cat. –1 (corresponding to 10.5 μg h –1 cm –2 ) and Faradic efficiency of 4.39% as well as superior stability in alkaline medium, which was superior to that of monometallic Ru and Cu nanostructures. Additionally, this work develops a new bimetallic combination of Ru and Cu, which promotes the strategy to design efficient electrocatalysts for electrochemical ammonia production under ambient conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

In situ characterization of phase transformations in petroleum pitch by high temperature X-ray diffraction

The phase transformation from isotropic to mesophase of a petroleum-derived pitch was monitored by in situ X-ray diffraction at 410 °C. The kinetics of the transformation were characterized by monitoring the growth of a broad peak at 2θ~24° and could be described by Avrami’s equation. The volatilization of low molecular weight components originally present in the pitch, or produced during the condensation reaction, was assessed by thermal gravimetry analysis, following the same thermal history. Ex situ characterizations of the pitch precursor before and after thermal treatment provided insight into the evolution of the molecular structure associated with mesophase generation (optical polarized microscopy, molecular weight distribution by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry, X-ray photoelectron spectroscopy, Auger spectroscopy, and thermal stability). Here, this investigation demonstrates the value of using complementary in situ and ex situ experimental techniques to characterize complex mechanisms during the processing of organic materials.

02 PETROLEUM↗
DOE OSTI2022

I.3.4.1.1 Overview of Advanced Characterization Within the Powertrain Materials Program (Task 4A1) (Oak Ridge National Laboratory); (Task 4A2) (Argonne National Laboratory); and (Task 4A3) (Pacific Northwest National Laboratory)

This report describes the activities performed during the third year of Thrust 4A, “Advanced Characterization,” within the DOE-EERE VTO PMCP. The goal of the PMCP, which was launched in October 2018, has been to accelerate design, development, demonstration, and deployment of new, cost-effective advanced alloy solutions via a modern ICME approach. The properties of these new materials are targeted to enable improvements in engine efficiency, lightweighting, and durability enhancement over the full range of on-road vehicle classes (e.g., Classes 1-8), including range extenders for future electric HD freight vehicles.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Damage of prismatic lithium‐ion cells subject to bending: Test, model, and detection

Abstract The mechanically induced internal short circuit (ISC) is one of the major safety concerns of lithium‐ion batteries. Mechanical abuse tests are often performed to evaluate the integrity and safety of lithium‐ion batteries under mechanical loadings. Except for the widely explored compression‐dominated indentation tests, bending is another typical real‐world loading condition that is tension‐dominated. To investigate the mechanical damage and ISC behavior of batteries under bending, we carried out controlled three‐point bending tests in four progressive steps on prismatic battery cells with maximum deflections ranging from 38% to 76% of the cell thickness. None of the tested cells experienced an ISC. We then conducted 3D X‐ray computed tomography (CT) scanning on the bent cells after unloading. X‐ray CT images showed three out of the four tested cells have extensive cracking in the electrode layers at the bottom side (opposite to the loading head). This indicates that cracking does not necessarily lead to an ISC under bending. Electrochemical impedance spectroscopy was also measured on the bent cells and substantial changes were observed. Both the bulk resistance and charge‐transfer resistance increased significantly after bending, which could influence the battery performance and lifespan. We then developed a detailed finite (FE) element model to further investigate the mechanical deformation and failure mechanisms. The FE model successfully predicts the load–displacement response and reproduces the deformation patterns. The findings and the FE model developed in the present study provide useful insights and tools for the battery structure and crash safety design. image

25 ENERGY STORAGE↗
DOE OSTI2021

In-situ x-ray computed tomography analysis of fracture mechanisms in ultrasonic additively manufactured Al-6061 alloy

The deformation and failure mechanisms in an ultrasonic additively manufactured Al-6061 alloy are studied using in-situ x-ray computed tomography during tensile deformation as well as ex-situ characterization with scanning electron microscopy. The role of pre-existing voids between the build layers on the failure mechanism is discussed with a focus on individual foil failures and void coalescence.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Residual stresses and microstructure within Allvac 718Plus laser powder bed fusion bars

The residual stresses within Allvac 718Plus bars built using LBPF with different laser powers, speeds and table displacements were measured using diffraction and mechanical methods and modelled with the baseplate attached and then removed. The residual stress profiles within the bars from the top surface down through the bulk were all quite similar, becoming less tensile due to a strain hardening mechanism. Table displacement has the greatest impact on residual stress, decreasing with increasing displacement/powder layer thickness. There was good agreement amongst the modeling and measurements. The microstructures were examined and varied slightly with energy density with higher densities having larger grains and enhanced post solidification diffusion. We found energy density had minimal impact on the residuals stresses within the parameters to produce dense material.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Quantifying adherence of oxide scales on steels exposed to high temperature and pressure steam

Oxide scale exfoliation is a major concern in fossil fuel power generation because it can cause tube blockages and erode valves and steam turbine components downstream. There is still considerable scientific and commercial interest to improve the mechanistic understanding of oxide failures by developing models to predict exfoliation and the extent of tube blockage as a function of operating conditions and component geometries. Tensile testing inside a scanning electron microscope was conducted on ferritic–martensitic and austenitic steel specimens with the steam side (Fe,Cr)-rich oxides grown after exposures for up to 1000 h in steam with ~100 ppb O 2 at 276 bar and 550°C. Multiple oxide layer cracks and delamination events were observed and analyzed in detail during the tests. Results from the testing agreed well with earlier observations that had identified the failure location at the outer–inner oxide layer for all tested materials. Calculated adhesion energies identified the outer–inner oxide interface of alloy 347HFG as the weakest interface.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microscopic analysis of copper current collectors and mechanisms of fragmentation under compressive forces

Extensive fragmentation of copper current collectors was observed after spherical indentation on prismatic and large-format pouch Li-ion cells by 3D X-ray computed tomography (XCT). Microscopic analysis including scanning electron microscopy (SEM), scanning transmission electron microscopy (STEM) and x-ray photoelectron microscopy (XPS) was carried out on copper current collectors from used commercial cells and pristine anodes. The copper-graphite cross-section images showed rough interface areas affected by reactions and diffusion in the used cell. Electron probe micro-analyzer (EPMA) element mapping showed the interface area was rich in oxygen and phosphorus. A detectable amount of phosphorus was also uniformly distributed inside the current collector. The same oxygen and phosphorus distributions were confirmed by STEM/EDS analysis. XPS depth profiles on multiple elements revealed the interface area of the aged anode was rich in Li, F, P, O and C and diffused at least 50 nm into the copper. In comparison, the pristine anode showed a very smooth C/Cu interface. No other elements were detected. For commercial cells, the reactions in the interface area and diffusion of multiple elements into the lattice and grain boundaries were responsible for the embrittlement of the copper current collectors. Finally, permanent cell capacity loss was observed in electrochemical performance of the indented cells.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Composition-Preserving Extraction and Characterization of Biomass Extrinsic and Intrinsic Inorganic Compounds

The inorganic content of biomass impairs size reduction tool life and the conversion process. Conventional ash extraction relies on furnace combustion that inevitably alters the inorganic compounds due to oxidation and decomposition. This study developed composition-preserving methods for extracting and analyzing extrinsic and intrinsic inorganic compounds. Comprehensive characterization was carried out on selected biomass feedstocks, including corn stover, pine residue, and pine anatomical fractions, to reveal their inorganic species and morphology. The extrinsic inorganic compounds were found to be dominated by quartz, along with other minor minerals, such as albite, microcline, and gehlenite, and have particle sizes ranging from tens to hundreds of micrometers. Among the pine anatomical fractions, the needles contain the highest intrinsic silicon content while the bark trapped the most extrinsic minerals. By correlation of the total ash and extrinsic inorganic contents to the wear behavior, both the extrinsic and intrinsic inorganic compounds were concluded to have made significant contributions to the wear process. Finally, the results here validated a new approach to characterize inorganic compounds in biomass and provided fundamental insights for their potential impact on preprocessing tool wear.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Characterization of Urbix Resources Natural Flake Graphite Material for Nuclear Applications (CRADA NFE-18-07340 Final Report)

Urbix Resources is a company specializing in graphite powder processing and purification. Urbix is looking to become the first domestic supplier of nuclear-grade graphite in the United States. This has led to a Cooperative Research and Development Agreement (CRADA) being established between the Oak Ridge National Laboratory (ORNL) and Urbix Resources, with the goal of characterizing a purified graphite feedstock supplied by Urbix Resources. The resulting data will then be used to determine the viability of a large-scale nuclear graphite production and qualification campaign. These characterization methods have been performed on the as-received graphite feedstock, a heat-treated batch of the feedstock, a milled batch of the feedstock, and a nuclear-grade graphite powder historically used in fuel production. The data from the heat-treated and milled feedstock will determine how different processing methods affect the powder’s physical properties, whereas the data from the nuclear grade graphite will provide information about the characteristics of a graphite previously accepted for nuclear applications. All of these powders have been characterized individually and as part of a resin-graphite blend (herein referred to as matrix) that has been used in past fuel experiments. The results of these experiments show that the Urbix powder and nuclear-grade graphite powder display notably different properties from one another in many cases, but this discrepancy may have been the result of the typical particle size of each powder. This hypothesis is supported by tests conducted on the milled powder, which showed a closer resemblance in properties to the nuclear-grade graphite than the as-received powder. The method for pressing the graphite matrix also had a noticeable effect on the measured properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗