Search NASA⌕ Search

Engineering topics

Watson, Ralph D.

Publications and source records attributed to Watson, Ralph D..

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Trapezoidal Wing Experimental Repeatability and Velocity Profiles in the 14- by 22-Foot Subsonic Tunnel

The AIAA Applied Aerodynamics Technical Committee sponsored a High Lift Prediction Workshop held in June 2010. For this first workshop, data from the Trapezoidal Wing experiments were used for comparison to CFD. This paper presents long-term and short-term force and moment repeatability analyses for the Trapezoidal Wing model tested in the NASA Langley 14- by 22-Foot Subsonic Tunnel. This configuration was chosen for its simplified high-lift geometry, publicly available set of test data, and previous CFD experience with this configuration. The Trapezoidal Wing is a three-element semi-span swept wing attached to a body pod. These analyses focus on configuration 1 tested in 1998 (Test 478), 2002 (Test 506), and 2003 (Test 513). This paper also presents model velocity profiles obtained on the main element and on the flap during the 1998 test. These velocity profiles are primarily at an angle of attack of 28 degrees and semi-span station of 83% and show confluent boundary layers and wakes.

Hannon, Judith A.↗
NASA NTRS2006

Skin Friction at Very High Reynolds Numbers in the National Transonic Facility

Skin friction coefficients were derived from measurements using standard measurement technologies on an axisymmetric cylinder in the NASA Langley National Transonic Facility (NTF) at Mach numbers from 0.2 to 0.85. The pressure gradient was nominally zero, the wall temperature was nominally adiabatic, and the ratio of boundary layer thickness to model diameter within the measurement region was 0.10 to 0.14, varying with distance along the model. Reynolds numbers based on momentum thicknesses ranged from 37,000 to 605,000. The measurements approximately doubled the range of available data for flat plate skin friction coefficients. Three different techniques were used to measure surface shear. The maximum error of Preston tube measurements was estimated to be 2.5 percent, while that of Clauser derived measurements was estimated to be approximately 5 percent. Direct measurements by skin friction balance proved to be subject to large errors and were not considered reliable.

Watson, Ralph D.↗
NASA NTRS2005

3-D High-Lift Flow-Physics Experiment - Transition Measurements

An analysis of the flow state on a trapezoidal wing model from the NASA 3-D High Lift Flow Physics Experiment is presented. The objective of the experiment was to characterize the flow over a non-proprietary semi-span three-element high-lift configuration to aid in assessing the state of the art in the computation of three-dimensional high-lift flows. Surface pressures and hot-film sensors are used to determine the flow conditions on the slat, main, and flap. The locations of the attachments lines and the values of the attachment line Reynolds number are estimated based on the model surface pressures. Data from the hot-films are used to determine if the flow is laminar, transitional, or turbulent by examining the hot-film time histories, statistics, and frequency spectra.

McGinley, Catherine B.↗
NASA NTRS2003

PIV Measurements in the 14 x 22 Low Speed Tunnel: Recommendations for Future Testing

During the period from February 4 to March 21, 2003 stereo digital particle imaging velocimetry measurements were made on a generic high lift model, the Trap Wing, as part of the High Lift Flow Physics Experiment. These measurements were the first PIV measurements made in the NASA, Langley Research Center 14 x 22 Foot Low Speed Tunnel, and several problems were encountered and solved in the acquisition of the data. It is the purpose of this paper to document the solutions to these problems and to make recommendations for further improvements to the tunnel/setup in order to facilitate future measurements of this type.

Watson, Ralph D.↗
NASA NTRS2003

Three-Dimensional Effects in Multi-Element High Lift Computations

In an effort to discover the causes for disagreement between previous two-dimensional (2-D) computations and nominally 2-D experiment for flow over the three-element McDonnell Douglas 30P-30N airfoil configuration at high lift, a combined experimental/CFD investigation is described. The experiment explores several different side-wall boundary layer control venting patterns, documents venting mass flow rates, and looks at corner surface flow patterns. The experimental angle of attack at maximum lift is found to be sensitive to the side-wall venting pattern: a particular pattern increases the angle of attack at maximum lift by at least 2 deg. A significant amount of spanwise pressure variation is present at angles of attack near maximum lift. A CFD study using three-dimensional (3-D) structured-grid computations, which includes the modeling of side-wall venting, is employed to investigate 3-D effects on the flow. Side-wall suction strength is found to affect the angle at which maximum lift is predicted. Maximum lift in the CFD is shown to be limited by the growth of an off-body corner flow vortex and consequent increase in spanwise pressure variation and decrease in circulation. The 3-D computations with and without wall venting predict similar trends to experiment at low angles of attack, but either stall too early or else overpredict lift levels near maximum lift by as much as 5%. Unstructured-grid computations demonstrate that mounting brackets lower the lift levels near maximum lift conditions.

Rumsey, Christopher L.↗
NASA NTRS2002

Three-Dimensional Effects on Multi-Element High Lift Computations

In an effort to discover the causes for disagreement between previous 2-D computations and nominally 2-D experiment for flow over the 3-clement McDonnell Douglas 30P-30N airfoil configuration at high lift, a combined experimental/CFD investigation is described. The experiment explores several different side-wall boundary layer control venting patterns, document's venting mass flow rates, and looks at corner surface flow patterns. The experimental angle of attack at maximum lift is found to be sensitive to the side wall venting pattern: a particular pattern increases the angle of attack at maximum lift by at least 2 deg. A significant amount of spanwise pressure variation is present at angles of attack near maximum lift. A CFD study using 3-D structured-grid computations, which includes the modeling of side-wall venting, is employed to investigate 3-D effects of the flow. Side-wall suction strength is found to affect the angle at which maximum lift is predicted. Maximum lift in the CFD is shown to be limited by the growth of all off-body corner flow vortex and consequent increase in spanwise pressure variation and decrease in circulation. The 3-D computations with and without wall venting predict similar trends to experiment at low angles of attack, but either stall too earl or else overpredict lift levels near maximum lift by as much as 5%. Unstructured-grid computations demonstrate that mounting brackets lower die the levels near maximum lift conditions.

Rumsey, Christopher L.↗
NASA NTRS2000

Review of Skin Friction Measurements Including Recent High-Reynolds Number Results from NASA Langley NTF

This paper reviews flat plate skin friction data from early correlations of drag on plates in water to measurements in the cryogenic environment of The NASA Langley National Transonic Facility (NTF) in late 1996. The flat plate (zero pressure gradient with negligible surface curvature) incompressible skin friction at high Reynolds numbers is emphasized in this paper, due to its importance in assessing the accuracy of measurements, and as being important to the aerodynamics of large scale vehicles. A correlation of zero pressure gradient skin friction data minimizing extraneous effects between tests is often used as the first step in the calculation of skin friction in complex flows. Early data compiled by Schoenherr for a range of momentum thickness Reynolds numbers, R(sub Theta) from 860 to 370,000 contained large scatter, but has proved surprisingly accurate in its correlated form. Subsequent measurements in wind tunnels under more carefully controlled conditions have provided inputs to this database, usually to a maximum R(sub Theta) of about 40,000. Data on a large axisymmetric model in the NASA Langley National Transonic Facility extends the upper limit in incompressible R(sub Theta) to 619,800 using the van Driest transformation. Previous data, test techniques, and error sources ar discussed, and the NTF data will be discussed in detail. The NTF Preston tube and Clauser inferred data accuracy is estimated to be within -2 percent of a power-law curve fit, and falls above the Spalding theory by 1 percent at R(sub Theta) of about 600,000.

Watson, Ralph D.↗
NASA NTRS1988

Structure of rough-wall turbulent boundary layers

Recent experiments have shown that, in rough-wall turbulent boundary layers, drag varies systematically with the spanwise aspect ratio lambda(z) (span/height) of roughness elements. In this paper, the effect of lambda(z) on turbulence structure has been examined. Based on lambda(z), the roughness in a transversely grooved surface with lambda(z) much greater than 1 is the opposite extreme of model plant canopies with lambda(z) much less than 1, studied in wind tunnels, whereas sandgrain is an intermediate type. Second-, third-, and fourth-order turbulence moments have been measured in turbulent boundary layers over transversely grooved and smooth surfaces and compared with available turbulence structure measurements over other types of surfaces. The near-wall turbulence structure is found to vary with lambda(z). The instantaneous motions involved in the flux of shear stress near the wall in smooth and transversely grooved surfaces are opposite in sign to those in three-dimensional roughness. The former is explained in terms of hairpin vortices alone, while the latter group is modeled to have an additional vortex (the so-called necklace vortex which straddles a three-dimensional roughness element near its base).

Bandyopadhyay, Promode R.↗
NASA NTRS1975

Wall Cooling Effects on Hypersonic Transitional/Turbulent Boundary Layers at High Reynolds Numbers

A 4 degree wedge was used to produce a thick turbulent boundary layer with an edge Mach number of 11. By using a two-dimensional model, the boundary layer was nearly free from upstream history effects associated with nozzle wall turbulent boundary layers. Heat-transfer distributions were used to define regions of laminar, transitional, and turbulent flow at several values of T(sub w)/T(sub t) for an edge unit Reynolds number of 0.47 x lot per cm. Pitot and total temperature profiles and skin-friction measurements were obtained at selected stations along the model. Turbulence parameters (mixing length/sigma and epsilon) were derived from the fully turbulent profiles and used to more completely define the "low Reynolds number" effect. Turbulent Prandtl number distributions are also presented.

Watson, Ralph D.↗