Engineering topics

Watts, L. A.

Publications and source records attributed to Watts, L. A..

7 records

NASA NTRS2008

Calculations of Solar Shortwave Heating Rates due to Black Carbon and Ozone Absorption Using in Situ Measurements

Results for the solar heating rates in ambient air due to absorption by black-carbon (BC) containing particles and ozone are presented as calculated from airborne observations made in the tropical tropopause layer (TTL) in January-February 2006. The method uses airborne in situ observations of BC particles, ozone and actinic flux. Total BC mass is obtained along the flight track by summing the masses of individually detected BC particles in the range 90 to 600-nm volume-equivalent diameter, which includes most of the BC mass. Ozone mixing ratios and upwelling and partial downwelling solar actinic fluxes were measured concurrently with BC mass. Two estimates used for the BC wavelength-dependent absorption cross section yielded similar heating rates. For mean altitudes of 16.5, 17.5, and 18.5 km (0.5 km) in the tropics, average BC heating rates were near 0.0002 K/d. Observed BC coatings on individual particles approximately double derived BC heating rates. Ozone heating rates exceeded BC heating rates by approximately a factor of 100 on average and at least a factor of 4, suggesting that BC heating rates in this region are negligible in comparison.

Gao, R. S.↗

NASA NTRS2006

Single-Particle Measurements of Midlatitude Black Carbon and Light-Scattering Aerosols from the Boundary Layer to the Lower Stratosphere

A single-particle soot photometer (SP2) was flown on a NASA WB-57F high-altitude research aircraft in November 2004 from Houston, Texas. The SP2 uses laser-induced incandescence to detect individual black carbon (BC) particles in an air sample in the mass range of approx.3-300 fg (approx.0.15-0.7 microns volume equivalent diameter). Scattered light is used to size the remaining non-BC aerosols in the range of approx.0.17-0.7 microns diameter. We present profiles of both aerosol types from the boundary layer to the lower stratosphere from two midlatitude flights. Results for total aerosol amounts in the size range detected by the SP2 are in good agreement with typical particle spectrometer measurements in the same region. All ambient incandescing particles were identified as BC because their incandescence properties matched those of laboratory-generated BC aerosol. Approximately 40% of these BC particles showed evidence of internal mixing (e.g., coating). Throughout profiles between 5 and 18.7 km, BC particles were less than a few percent of total aerosol number, and black carbon aerosol (BCA) mass mixing ratio showed a constant gradient with altitude above 5 km. SP2 data was compared to results from the ECHAM4/MADE and LmDzT-INCA global aerosol models. The comparison will help resolve the important systematic differences in model aerosol processes that determine BCA loadings. Further intercomparisons of models and measurements as presented here will improve the accuracy of the radiative forcing contribution from BCA.

Schwartz, J. P.↗

NASA NTRS1985

Examination of returned solar-max surfaces for impacting orbital debris and meteoroids

Previous theoretical studies predicted that in certain regions of earth orbit, the man-made earth orbiting debris environment will soon exceed the interplanetary meteoroid environment for sizes smaller than 1 cm. The surfaces returned from the repaired Solar Max Mission (SMM) by STS 41-C on April 12, 1984, offered an excellent opportunity to examine both the debris and meteoroid environments. To date, approximately 0.7 sq. met. of the thermal insulation and 0.05 sq. met of the aluminum louvers have been mapped by optical microscope for crater diameters larger than 40 microns. Craters larger in diameter than about 100 microns found on the initial 75 micron thick Kapton first sheet on the MEB (Main Electronics Box) blanket are actually holes and constitute perforations through that blanket. The following populations have been found to date in impact sites on these blankets: (1) meteoritic material; (2) thermal paint particles; (3) aluminum droplets; and (4) waste particles.

Kessler, D. J.↗

NASA NTRS1985

Guide to using lunar soil and simulants for experimentation

It is pointed out that lunar soil can be described as well-graded silty sands or sandy silts with an average particle size by weight in the range from 0.040 to 0.130 mm. The density of in situ bulk lunar soil is typically 1.4 to 1.9 g/cu cm. Changes in soil from moon to laboratory are considered along with some critical differences between simulants and lunar soil. Attention is given to agglutinates, iron metal distributed throughout the agglutinatic glass, solar wind hydrogen, and major lunar minerals (anorthite, pyroxene, ilmenite, olivine). The use of lunar fines as experimental samples is discussed, and the characteristics of simulants for experiments are examined, taking into account grain size distribution, particle type distribution, a highlands simulant, and a high titanium mare simulant. Simulants for testing equipment and structures are also described.

Allton, J. H.↗

NASA NTRS1977

Orbiter Cloud Photopolarimeter for the Pioneer Venus mission

The Orbiter Cloud Photopolarimeter (OCPP) to be flown aboard the Pioneer Venus Orbiter spacecraft is described. This instrument, while in orbit about the planet Venus, will perform polarimetric and radiometric mapping of the Venus atmosphere in four spectral bands centered in the near ultraviolet, visible, and near infrared regions. Additionally, the instrument is equipped to provide moderate resolution imaging of the time varying cloud patterns in the near ultraviolet. In another mode of operation the instrument is capable of profiling the atmosphere at the limb of the planet to measure the particulate layering. Information resulting from these measurements is intended to provide an understanding of the global cloud dynamics and the atmospheric structure and composition on Venus. The basic operation and functional elements of the instrument are discussed. The optical configuration incorporating a polarization analyzing technique with improved accuracy is described. Long-term and short-term calibration techniques along with expected instrument performance characteristics are summarized.

Russell, E. E.↗

NASA NTRS1973

Pioneer imaging photopolarimeter optical system.

The imaging photopolarimeter aboard the Pioneer 10 spacecraft en route to the vicinity of Jupiter is described. This instrument is capable of moderate resolution spin-scan imaging and high precision polarimetric and photometric mapping of Jupiter in red and blue light. The field of view can be selectively changed from 0.50 mrad square to 40 mrad square to accommodate resolution and radiance combinations ranging from the zodiacal background to that of Jupiter. Optical materials were chosen to survive, with minimum degradation, the rigors of a nearly 2-year journey to Jupiter including transit through the Jovian trapped radiation belts. The optics are described in detail, and the operational system is outlined. The procedures for preflight and in-flight calibration are described, and some performance characteristics and preliminary flight results are presented.

Pellicori, S. F.↗

NASA NTRS1972

Outer planet Grand Tour missions photometry/polarimetry experiment critical components study

Work performed during this effort was limited to two primary areas of technical concern: optical design optimization, and sensor selection. An optical system concept was established, and various system components were evaluated through experimental test sequences. Photodetectors were investigated for the applicability in meeting OPGT requirements as constrained by the photometry/polarimetry team directives. The most promising (gallium arsenide PMT) was further experimentally tested to ascertain its behavior with respect to anticipated environmental conditions. Results of testing and summary of the preceding tradeoff study effort are presented.

Pellicori, S. F.↗