Engineering topics

Weaver, C.

Publications and source records attributed to Weaver, C..

5 records

DOE OSTI2025

Prototype acoustic positioning system for the Pacific Ocean Neutrino Experiment

We present the design and initial performance characterization of the prototype acoustic positioning system intended for the Pacific Ocean Neutrino Experiment. It comprises novel piezo-acoustic receivers with dedicated filtering- and amplification electronics installed in P-ONE instruments and is complemented by a commercial system comprised of cabled and autonomous acoustic pingers for sub-sea installation manufactured by Sonardyne Ltd. We performed an in-depth characterization of the acoustic receiver electronics and their acoustic sensitivity when integrated into P-ONE pressure housings. These show absolute sensitivities of up to -125 dB re V2/μPa2 in a frequency range of 10–40 kHz. We furthermore conducted a positioning measurement campaign in the ocean by deploying three autonomous acoustic pingers on the seafloor, as well as a cabled acoustic interrogator and a P-ONE prototype module deployed from a ship. Using a simple peak-finding detection algorithm, we observe high accuracy in the tracking of relative ranging times at approximately 230–280 μs at distances of up to 1600 m, which is sufficient for positioning detectors in a cubic-kilometer detector and which can be further improved with more involved detection algorithms. The tracking accuracy is further confirmed by independent ranging of the Sonardyne system and closely follows the ship's drift in the wind measured by GPS. The absolute positioning shows the same tracking accuracy with its absolute precision only limited by the large uncertainties of the deployed pinger positions on the seafloor.

Data analysis↗

NASA NTRS2014

Retrieval of Methane Source Strengths in Europe Using a Simple Modeling Approach to Assess the Potential of Spaceborne Lidar Observations

We investigate the sensitivity of future spaceborne lidar measurements to changes in surface methane emissions. We use surface methane observations from nine European ground stations and a Lagrangian transport model to infer surface methane emissions for 2010. Our inversion shows the strongest emissions from the Netherlands, the coal mines in Upper Silesia, Poland, and wetlands in southern Finland. The simulated methane surface concentrations capture at least half of the daily variability in the observations, suggesting that the transport model is correctly simulating the regional transport pathways over Europe. With this tool we can test whether proposed methane lidar instruments will be sensitive to changes in surface emissions. We show that future lidar instruments should be able to detect a 50% reduction in methane emissions from the Netherlands and Germany, at least during summer.

surface fluxes↗

NASA NTRS2009

Pulsed Airborne Lidar Measurements of Atmospheric CO2 Column Absorption and Line Shapes from 3-13 km Altitudes

We have developed a lidar technique for measuring the tropospheric C02 concentrations as a candidate for NASA's planned ASCENDS mission. Our technique uses two pulsed laser transmitters allowing simultaneous measurement of a C02 absorption line in the 1570 nm band, 02 extinction in the Oxygen A-band and surface height and backscatter. The lidar measures the energy and time of flight of the laser echoes reflected from the atmosphere and surface. The lasers are stepped in wavelength across the C02 line and an 02 line region during the measurement. The receiver uses a telescope and photon counting detectors, and measures the background light and energies of the laser echoes from the surface along with scattering from any aerosols in the path. The gas extinction and column densities for the C02 and 02 gases are estimated from the ratio of the on- and off- line signals via the DIAL technique. Time gating is used to isolate the laser echo signals from the surface, and to reject laser photons scattered in the atmosphere. We have developed an airborne lidar to demonstrate the C02 measurement from the NASA Glenn Lear 25 aircraft. The airborne lidar steps the pulsed laser's wavelength across a selected C02 line with 20 steps per scan. The line scan rate is 450 Hz and laser pulse widths are I usec. The time resolved laser backscatter is collected by a 20 cm telescope, detected by a photomultiplier and is recorded by a photon counting system. We made initial airborne measurements on flights during October and December 2008. Laser backscatter and absorption measurements were made over a variety of land and water surfaces and through thin and broken clouds. Atmospheric C02 column measurements using the 1571.4, 1572.02 and 1572.33 nm C02 lines. Two flights were made above the DOE SGP ARM site at altitudes from 3-8 km. These nights were coordinated with DOE investigators who Hew an in-situ C02 sensor on a Cessna aircraft under the path. The increasing C02 line absorptions with altitudes were evident and comparison with in-situ measurements showed agreements to 6 ppm. This spring we improved the aircraft's nadir window. During July and August 2009 we made 9 additional 2 hour long flights and measured the atmospheric C02 absorption and line shapes using the 1572.33 nm C02 line. Measurements were made at stepped altitudes from 3-13 km over a variety of surface types in Nebraska, Illinois, the SGP ARM site, and near and over the Chesapeake Bay in North Carolina and Virginia. Strong laser signals and clear line shapes were observed at all altitudes, and some measurements were made through thin clouds. The flights over the ARM site were underflown with in-situ measurements made from the DOE Cessna. The Oklahoma and east coast t1ights were coordinated with a LaRC/ITT C02 lidar on the LaRC UC-12 aircraft, a LaRC in~situ C02 sensor, and the Oklahoma flights also included a JPL C02 lidar on a Twin Otter aircraft. Ed Browell and Gary Spiers led the LaRC and JPL teams. More details of the t1ights, measurements and analysis will be described in the presentation.

Abshire, J. B.↗

NASA NTRS2007

A Slow Retrieval Algorithm for Satellite and Surface Based Instruments

We present results of a retrieval algorithm for satellite and ground based instruments using the Arizona radiative transfer code. A state vector describing the atmospheric and surface condition is iteratively modified until the calculated radiances match the observed values. Elements of the state vector include: aerosol concentrations, radius, optical properties, mass-weighted altitudes, chlorophyll concentration and wind speed. While computationally expensive, many assumptions used in other retrieval algorithms are not invoked. We present co-located retrievals for MODIS, SEAWIFS and nearby AERONET sites. MODIS AQUA and SEA WIFS: Ten MODIS (.412 - 2.110 microns) and eight SEA WIFS (.412-.865 microns) radiances (.412-.865 microns) include channels where aerosols absorb and reflect radiation. We focus on retrieving bio-mass burning aerosols that are advected over open ocean. Since chlorophyll absorbs at frequencies where black carbon absorbs, our retrieval algorithm accounts for chlorophyll absorption by simultaneously retrieving both aerosol and chlorophyll amount. Our retrieved chlorophyll concentrations are similar to those from the Ocean Color Group. AERONET: Both Almucantar and Principle plane radiances are used to retrieve the state of the atmosphere and ocean conditions. Our retrieved aerosol size distributions and optical properties are consistent with the aerosol inversions from the AERONET group.

Weaver, C.↗

NASA NTRS2002

Mass Conservation in a Chemical Transport Model and its Effect on CO2 and SF6 Simulations

Chemical transport models (CTMs) must conserve mass to be useful for applications involving assessment of the effect of various pollutants on the troposphere and stratosphere. Furthermore, calculations of the evolution of constituents such as SF6 are used to evaluate overall model transport, and interpretation of such simulations is clouded if mass conservation is not assured. For realistic simulations or predictions, it is crucial that constituents are not produced or lost by transport or other processes in the CTMs. Analysis of CO2 and SF6 experiments using a CTM shows that problems with mass conservation can seriously degrade the simulations. Failure to conserve mass results from inconsistency of the surface pressure tendency and the divergence of horizontal mass flux when the model is forced by assimilated meteorological data. We have developed an effective method to eliminate the inconsistency by modifying the divergent part of the wind field. The changes in the wind fields are quite small but the impact on mass conservation is large. Parameterizations of physical processes such as convection or turbulent transport can also affect mass conservation. The lack of conservation is small but accumulates when integrations are lengthy such as required for SF6. This lack of conservation is found using winds from either a GCM or from an assimilation system. A simple adjustment removes much of the inaccuracy in the convective parameterization. A CO2 simulation using assimilated winds from the most recent version of the Goddard Earth Observing System Data Assimilation System will be used to illustrate the impact of these transport improvements.

Zhu, Z.↗