Engineering topics
Publications and source records attributed to Weber, Adam Z..
A multiphysics model is presented to study potential losses in Cu-MEAs and how various physical phenomena impact the product distribution of CO 2 reduction.
Direct conversion of methane to methanol has been a long-sought objective. Partial oxidation by thermal catalysis is possible but suffers from a rapid loss in methanol selectivity with increasing methane conversion. More recently, the electrochemical oxidation of methane, using water, rather than oxygen, as the oxidizing agent has been considered in both aqueous electrolyte systems and membrane-electrode assemblies (MEAs). While promising results have been demonstrated using MEAs, the absence of key metrics of system performance make it hard to compare and contrast the results of different investigators. Overall, this Perspective examines why MEAs are well-suited for the electrochemical oxidation of methane, defines the metrics for assessing MEA performance, and reviews the progress in the field. An analysis of the challenges to finding suitable electrocatalysts is included with the aim of guiding the search for electrocatalysts that would be both active and selective for the conversion of methane to methanol.
Exploring the origins of local transport resistance and characterizing the oxygen transport resistances in the catalyst layer (RCL) are critical for cost reduction. In this paper, a comprehensive mesoscopic model for simulating coupled transport processes of oxygen and water vapor for different structural parameters under different operating conditions in reconstructed microstructures is proposed. The local transport resistance is calculated after achieving the limiting current density and the effective diffusivity of oxygen. The results demonstrate that RCL increases greatly with decreasing platinum loading (LPt) and the transport resistances in other components of the cell dominate for high-loadings. Both the reduced oxygen permeation coefficient in the ionomer thin-film and the adsorption resistance account for the origins of local transport resistance. The local transport resistance increases with the bare carbon ratio for a constant LPt and Pt/C ratio due to the decreased effective ionomer surface, and increases with the I/C ratio due to the increased ionomer thickness and decreased Knudsen diffusivity. Due to the presence of liquid water, a slight decrease followed by an increase of the local transport resistance versus relative humidity is obtained. The contribution of ionomer thin-films to RCL is more sensitive to liquid saturation compared with that of pores. This journal is
Perfluorosulfonic acids (PFSAs) are commonly used as solid polymer electrolyte membranes (PEMs) in electrochemical energy devices, where they are vulnerable to attack by radical species during operation. A popular strategy to combat this problem is to introduce radical scavengers like cerium (Ce) ions that neutralize these species before they attack the PFSA. Such cation doping creates a multi-ion system, in which understanding the mechanisms of cation solvation and transport becomes important for the effective design and utilization of PFSA–cation systems. Ce ions also provide a representative model system for multication-exchanged ionomers in electrochemical systems. In this study, hydration and conductivity measurements, along with X-ray fluorescence and scattering, are employed to elucidate how Ce ion exchange alters PFSA’s ionic solvation, as well as nano- and mesoscale morphologies, which ultimately control its ion transport properties. A molecular transport model is used to deconvolute the impact of Ce ions on the local solvation structure of water in the membrane from mesoscale changes of the transport pathways. The combined experimental and theoretical analysis reveals a nonlinear decrease in conductivity driven by cation solvation at the molecular level and morphological changes at longer length scales. Migration–diffusion coupling, its nonlinear dependence on ion exchange and hydration, and its overall implications for ionomer performance are also discussed. Finally, these findings have the potential to be translated into other mixed cation–ionomer systems for a wide range of energy and environmental devices.
Not Available
Increasing the utilization of Pt and Pt alloy catalysts in polymer electrolyte fuel cell cathodes is critical to improving the high power density operation, particularly at low Pt loadings. State of the art electrodes are fabricated in an ink deposition process that leads to uncontrolled electrode architecture with random aggregates of functional domains (catalyst, ionomer, and pore volume) (1). The randomness in the domains induces high tortuosity transport pathways for ions and fluids, which cause severe transport resistance during high current density operation. Thin ionomer films cause additional transport resistance and poisoning of the Pt catalyst, which becomes more significant at low Pt loadings. Reducing the amount of ionomer in the catalyst domain without affecting the ionic transport resistance is key to improving the utilization of the Pt and reducing the transport resistance at low Pt loading. Rational design of the electrode structure with controlled low tortuous ionic transport pathways could improve performance. The introduction of the ionomer pathways could also enable reduction of the ionomer volume in the catalyst domain, reducing the transport resistance. Middelmen et al. proposed electrode structures consisting of aligned components in a low tortuosity configuration to improve performance (2). In this work, we present an alternative electrode structure based on a vertically aligned array of Nafion pillars in the cathode catalyst layer, as shown in Figure 1a. Figure 1b shows the SEM image of the Nafion pillars. Furthermore, Pt supported on carbon catalyst was deposited on the Nafion pillars to fabricate a meso-structured electrode. Nafion pillars provide high conductive and low tortuous pathways for protons, reducing the effective transport distance, and enabling reduction of the ionomer binder in the catalyst domain.
The open-circuit voltage (OCV) is the measured potential when no current is drawn from a cell. Additionally, theoretically this potential is given by the equilibrium potential, which is determined from thermodynamics based on the operating conditions. In practice, the actual potential at zero current is measured to be approximately 300 mV lower than the theoretical value.
The electrochemical reduction of CO 2 (CO 2 R) to value-added products is an attractive technology for tackling the rising atmospheric CO 2 levels and storing intermittent renewable energy into chemical bonds. Fundamental understanding of CO 2 R has progressed significantly in recent years and is critical in the development of CO 2 R to liquid-fuel electrolyzers, where gas-diffusion electrodes (GDEs) have been shown to be key enabling architectures. Various designs have been proposed and studied in the literature to enhance overall selectivity, rates, and maximize the conversion of CO 2 , the latter of which is only now being recognized as a critical issue. In this respect, there is a need to explore the governing phenomena inherent in these architectures to enable optimization. Mathematical modeling is ideally suited to tackle and explore these multiphysics interactions and provide virtual design analysis. In this talk, we discuss modeling methodologies and physics inherent in these devices and present our recent modeling of GDEs for CO 2 reduction. We specifically examine the impacts of multiphase flow and related phenomena on overall cell performance. We then explore the performance and limitations of various cell designs guided by simulation results and examine potential methods for improving water management and tuning catalyst selectivity including the use of different anion-exchange and bipolar membranes. Finally, we discuss the disparities in local environments between aqueous and GDE devices and propose strategies to reduce the gap in knowledge between the two systems.
To commercialize successfully polymer-electrolyte electrolyzers and optimize their performance, one requires a detailed understanding of the underlying physics and phenomena. Mathematical modeling is ideally suited to explore such intricacies. In this Tutorial, the modeling equations and approaches towards both proton- and hydroxide-conducting polymer electrolyzers will be detailed. This includes the introduction of the applied voltage breakdown that separates the overall polarization curve into its constitutive parts such that the limiting mechanisms can be ascertained. Throughout, different case studies will be explored including impacts of bubble generation, liquid versus vapor feed, and pH changes due to carbonate and hydroxide solution feeds. A key focus of the Tutorial will be in exploring and describing the various transport and competing phenomena within the electrolyzer cell.
Here, a particle finite element method-based model is proposed to analyze droplet dynamics problems, particularly droplet spreading on solid substrates (wetting). The model uses an updated Lagrangian framework to formulate the governing equations of the liquid. The curvature of the liquid surface is tracked accurately using a deforming boundary mesh. In order to predict the spreading rate of the droplet on the solid substrate and track the corresponding contact angle evolution, dissipative forces at the contact line are included in the formulation in addition to the Navier-slip boundary conditions at the solid–liquid interface. The inclusion of these boundary conditions makes it possible to account for the induced Young’s stress at the contact line and for the viscous dissipation along the solid–liquid interfacial region. These are found to be essential to obtain a mesh-independent physical solution. The temporal evolution of the contact angle and the contact line velocity of the proposed model are compared with spreading droplets and micro-sessile droplet injection experiments and are shown to be in good agreement.
Glassy polymers are often used for gas separations because of their high selectivity. Although the dual-mode permeation model correctly fits their sorption and permeation isotherms, its physical interpretation is disputed, and it does not describe permeation far from steady state, a condition expected when separations involve intermittent renewable energy sources. To develop a more comprehensive permeation model, we combine experiment, molecular dynamics, and multiscale reaction–diffusion modeling to characterize the time-dependent permeation of N 2 and CO 2 through a glassy poly(dimethyl phenylene oxide) membrane, a model system. Simulations of experimental time-dependent permeation data for both gases in the presteady-state and steady-state regimes show that both single- and dual-mode reaction–diffusion models reproduce the experimental observations, and that sorbed gas concentrations lag the external pressure rise. The results point to environment-sensitive diffusion coefficients as a vital characteristic of transport in glassy polymers.
Cost and durability remain the two major barriers to the widespread commercialization of polymer electrolyte membrane fuel cell (PEMFC)-based power systems, especially for the most impactful but challenging fuel cell electric vehicle (FCEV) application. Commercial FCEVs are now on the road; however, their PEMFC systems do not meet the cost targets established by the U.S. Department of Energy, primarily due to the high platinum loading needed on the cathode to achieve the requisite performance and lifetime. Furthermore, while the activities of a number of commercial Pt-based alloy cathode catalysts exceed the beginning-of-life (BOL) targets, these activities, and the overall cathode performance, degrade via a variety of mechanisms described herein. Degradation is mitigated in current FCEVs by utilizing a cathode catalyst with a lower BOL activity (e.g., much lower transition metal alloy content and larger BOL nanoparticle size), necessitating higher catalyst loadings, and through the utilization of system controls that avoid conditions known to exacerbate degradation processes, such as limiting the fuel cell stack voltage range. The design and development of active and robust materials and eliminating the need for vehicle mitigation strategies would greatly simplify the operating system, allowing for greater transient operation, avoiding large hybridization, and curtailing of fuel cell power. Although system mitigation strategies have provided the near-term pathway for FCEV commercialization, material-specific solutions are required to further reduce costs and improve operability and efficiency. Future material developments should focus on stabilization of the electrode structure and minimization of the catalyst particle susceptibility to dissolution caused by oxide formation and reduction over PEMFC cathode-relevant operating potentials plus minimization of support corrosion. Ex situ accelerated stress tests have provided insight into the processes responsible for material and performance degradation and will continue to provide useful information on the relative stability of materials and benchmarks for robust and stable materials-based solutions not requiring system mitigation strategies to achieve adequate lifetime.
Unitized regenerative fuel cells (URFC) convert electrical energy to and from chemical bonds in hydrogen. URFCs have the potential to provide economical means for efficient long-term, seasonal, energy storage and on-demand conversion back to electrical energy. We first optimize the catalyst layer for discrete electrolyzer and fuel cell and then configure the URFC. The goal is to identify a cost competitive configuration for URFCs, and demonstrate it in terms of upper limit of round trip efficiencies (RTEs). Two possible configurations of URFCs are compared via experiments and techno-economic analysis (TEA), which emphasize the advantages of the unconventional constant-electrode (CE) URFC over the traditional constant-gas (CG) configuration. We also study the stability via accelerated stress tests (ASTs) and demonstrate steady state operation in a daily cycle for day to night energy shifting. From the investigations, the optimum composition of the URFC anode catalyst layer is 90 at% Ir-black balanced by Pt-black for both CE and CG configurations. At 80 °C and 1 A cm -2 , the optimized CE URFC achieves 57% and 60% RTE with air and O 2 as the reductant gases, respectively. We then evaluated the differences in durability using an AST over 10k charge–discharge cycles; the results reveal that the wider potential window at the anode in CE (0.05–1.55 V) has minimal effect on catalyst layer stability compared to CG (0.55–1.55 V). Furthermore, there was no degradation up to the range of 2k–5k cycles; beyond that the fuel cell (discharge) performance degraded while the electrolyzer (charge) performance was still stable. Finally, the observations here indicate substantial potential to employ URFCs as efficient and cost-effective bidirectional energy-conversion devices within energy storage and utilization systems after appropriate technological and operational optimizations.
Not Available
This review of design and operating conditions of electrochemical CO 2 reduction covers electrolytes, electrodes, reactors, temperature, pressure, and pH effects.
Not Available