Search NASA⌕ Search

Engineering topics

Weber, C. R.

Publications and source records attributed to Weber, C. R..

At least 19 records

Observations and properties of the first laboratory fusion experiment to exceed a target gain of unity

An indirect-drive inertial fusion experiment on the National Ignition Facility was driven using 2.05 MJ of laser light at a wavelength of 351 nm and produced 3.1±0.16 MJ of total fusion yield, producing a target gain G=1.5±0.1 exceeding unity for the first time in a laboratory experiment [Phys. Rev. E 109, 025204 (2024)]. Herein we describe the experimental evidence for the increased drive on the capsule using additional laser energy and control over known degradation mechanisms, which are critical to achieving high performance. Further, improved fuel compression relative to previous megajoule-yield experiments is observed. Novel signatures of the ignition and burn propagation to high yield can now be studied in the laboratory for the first time.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reduced mixing in inertial confinement fusion with early-time interface acceleration

In inertial confinement fusion (ICF) implosions, the interface between the cryogenic DT fuel and the ablator is unstable to shock acceleration (the Richtmyer-Meshkov instability, RM) and constant acceleration (Rayleigh-Taylor instability, RT). Instability growth at this interface can reduce the final compression, limiting fusion burnup. If the constant acceleration is in the direction of the lighter material (negative Atwood number), the RT instability produces oscillatory motion that can stabilize against RM growth. Theory and simulations suggest this scenario occurred at early times in some ICF experiments on the National Ignition Facility, possibly explaining their favorable performance compared to one-dimensional simulations. In conclusion, this characteristic is being included in newer, lower adiabat designs, seeking to improve compression while minimizing ablator mixing into the fuel.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Modeling ablator grain structure impacts in ICF implosions

High-density carbon is a leading ablator material for inertial confinement fusion (ICF). This and some other ablator materials have grain structure which is believed to introduce very small-scale (~nm) density inhomogeneity. In principle, such inhomogeneity can affect key ICF metrics like fuel compression and yield, by, for example, acting as a seed for instabilities and inducing mix between ablator and fuel. However, assessments of such effects are uncertain due to the difficulty of modeling this small-scale structure in ICF simulations, typically requiring reduced-resolution modeling that scales these features. We present a grain model and show both the impact of de-resolving grains and the complex mixing dynamics such structures can induce. We find that different methods for de-resolving grains can yield both different total deposition of kinetic energy perturbations and different fuel–ablator mixing. We then show a simple-to-implement approach for approximately conserving the deposition of perturbed kinetic energy and demonstrate that, for the present grain model and test cases, this approach yields a reasonably matched time history of mix width between less and more resolved grain models. The simulations here also demonstrate the complex interaction history between grain-induced mixing and instability around the fuel–ablator interface, showing, for example, that the grain-induced perturbations typically trigger instability of conduction-driven density gradients in the DT fuel, enhancing mix penetration early in the acceleration of the shell. Furthermore simulating both microscale and nanoscale grains, we find initial evidence for larger mixing in the microscale case of the present model, despite smaller deposited kinetic energy perturbation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental achievement and signatures of ignition at the National Ignition Facility

An inertial fusion implosion on the National Ignition Facility, conducted on August 8, 2021 (N210808), recently produced more than a megajoule of fusion yield and passed Lawson's criterion for ignition [Phys. Rev. Lett. 129, 075001 (2022)]. Here we describe the experimental improvements that enabled N210808 and present the first experimental measurements from an igniting plasma in the laboratory. Ignition metrics like the product of hot-spot energy and pressure squared, in the absence of self-heating, increased by ~ 35%, leading to record values and an enhancement from previous experiments in the hot-spot energy (~ 3×), pressure (~ 2×), and mass (~ 2×). These results are consistent with self-heating dominating other power balance terms. The burn rate increases by an order of magnitude after peak compression, and the hot-spot conditions show clear evidence for burn propagation into the dense fuel surrounding the hot spot. These novel dynamics and thermodynamic properties have never been observed on prior inertial fusion experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Design of inertial fusion implosions reaching the burning plasma regime

One of the last remaining milestones in fusion research before reaching ignition is creating a burning plasma state, where alpha particles from deuterium-tritium (DT) fusion reactions redeposit their energy as the dominant source of heating in the plasma. The indirect-drive inertial confinement fusion approach at the National Ignition Facility (NIF) uses a laser-generated radiation cavity (hohlraum) to spherically implode DT fuel to high temperatures and densities in a central ”hot spot”. Here, we deliver more energy to the hot spot than ever before, while maintaining the extreme pressures required for inertial confinement, by increasing the size of the implosion compared to previous experiments. We develop more efficient hohlraums, to drive these larger implosions within NIF’s current laser energy and power capability and control symmetry by moving energy between laser beams and by changing the shape of the hohlraum. These designs resulted in record fusion powers of 1.5 petawatts, greater than the input power of the laser, and 170 kJ of fusion energy. Radiation hydrodynamics simulations show alpha particle heating as the dominant term in the hot spot energy balance, e.g. a burning plasma state. This work is expected to motivate future studies of burning plasmas and improve predictive capability by providing a benchmark for modeling used to understand the proximity to ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Design of inertial fusion implosions reaching the burning plasma regime

Abstract In a burning plasma state 1–7 , alpha particles from deuterium–tritium fusion reactions redeposit their energy and are the dominant source of heating. This state has recently been achieved at the US National Ignition Facility 8 using indirect-drive inertial-confinement fusion. Our experiments use a laser-generated radiation-filled cavity (a hohlraum) to spherically implode capsules containing deuterium and tritium fuel in a central hot spot where the fusion reactions occur. We have developed more efficient hohlraums to implode larger fusion targets compared with previous experiments 9,10 . This delivered more energy to the hot spot, whereas other parameters were optimized to maintain the high pressures required for inertial-confinement fusion. We also report improvements in implosion symmetry control by moving energy between the laser beams 11–16 and designing advanced hohlraum geometry 17 that allows for these larger implosions to be driven at the present laser energy and power capability of the National Ignition Facility. These design changes resulted in fusion powers of 1.5 petawatts, greater than the input power of the laser, and 170 kJ of fusion energy 18,19 . Radiation hydrodynamics simulations 20,21 show energy deposition by alpha particles as the dominant term in the hot-spot energy balance, indicative of a burning plasma state.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fill tube dynamics in inertial confinement fusion implosions with high density carbon ablators

Plasma jets, such as γ-ray burst jets, Herbig–Haro jets, μ-quasar jets, and active galactic nuclei jets, are found throughout the universe [S. Mendoza et al., Rev. Mex. Astron. Astrofis. 41, 453 (2005)]. Plasma jets are also present in indirect drive inertial confinement fusion experiments originating from the capsule's fill tube and occasionally from divots and voids in the capsules, particles on the exterior of the capsule, or from the tent holding the capsule in the target. This paper looks at two different gas-filled capsule implosions containing a plasma jet resulting from a capsule fill tube and fill channel, both of which utilized high density carbon ablators. Two models were developed, a drag and a snowplow model, which use the time-dependent motion of the injected mass through the hotspot to estimate the mass injected into the hotspot from the fill tube and channel, arriving at an average injected mass of ~84.5 ± 25.5 ng for the first experiment and 91 ± 20 ng for the second experiment. Furthermore, unlike previous methods to estimate fill tube injected mass, these techniques do not assume that the mixed mass is in thermal equilibrium with the hotspot or that the x-ray emission is only coming from within the hotspot itself. This paper also discusses the features seen in these experiments which include limb brightening in the shell for undoped ablators and flattening in the ablator from shadowing by the fill tube.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurements of enhanced performance in an indirect drive inertial confinement fusion experiment when reducing the contact area of the capsule support

Experimental results from indirectly driven inertial confinement fusion experiments testing the performance gained from using an alternate capsule tent support are reported. The polar tent describes an alternate geometry for the thin membrane used to support the Deuterium–Tritium (DT) filled capsule. In this work, the contact area is reduced by 23 times by locating the tent support close to the poles of the capsule. The polar tent experiments are repeats of previous 3 shock 1.63 MJ, 400 TW high foot experiments and use a 165 μm thick silicon doped carbon hydrogen plastic (CH) shell. Using the polar tent support, we report a DT neutron yield of 1.07 ×1016, 76% higher than the expected Y DT ∝V 7.7 scaling. This is, at the time of writing, the highest neutron yield to date from a CH shell implosion. Furthermore, we find that the inferred pressure when using the polar tent is significantly above the model based on analytic scaling even when accounting for tent effects. Analysis of x-ray and neutron images shows the reduction of lobes produced by nominal tent features. The reduction of these features in the polar tent experiments leads to decreased low mode (P2 and P4) asymmetry compared to the nominal tent results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Recent and planned hydrodynamic instability experiments on indirect-drive implosions on the National Ignition Facility

At National Ignition Facility (NIF), yield amplification due to alpha particle heating approached ~3 in the highest performing inertial confinement fusion (ICF) implosions, while yield amplification of ~15-30 is needed for ignition. Hydrodynamic instabilities are a major factor in degradation of implosions while understanding and mitigation of the instabilities are critical to achieving ignition. This article describes recent and planned hydrodynamic instability experiments with several focused platforms that have been developed to directly measure these instabilities in all phases of ICF implosions. Measurements of ripple-shock generation at OMEGA laser have indicated initial seeds for the instabilities in three ablators - plastic (CH), beryllium, and high-density carbon (HDC). Hydrodynamic Growth Radiography (HGR) platform was used to measure instability growth at the ablation front in the acceleration phase of implosions. This platform used pre-imposed 2-D perturbations for growth factor measurements at different perturbation wavelengths and was also used to measure growth of “native roughness” modulations, fill tubes, and capsule support membranes or “tents”. Also, in the acceleration phase several new experimental platforms have been or are being developed to measure instability growth at the ablator-ice interface. In the deceleration phase of implosions, “self-emission” and “self-backlighting” platforms were developed to measure perturbations near peak compression. This article reviews recent progress and results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hotspot conditions achieved in inertial confinement fusion experiments on the National Ignition Facility

We describe the overall performance of the major indirect-drive inertial confinement fusion campaigns executed at the National Ignition Facility. With respect to the proximity to ignition, we can describe the performance of current experiments both in terms of no-burn ignition metrics (metrics based on the hydrodynamic performance of targets in the absence of alpha-particle heating) and in terms of the thermodynamic properties of the hotspot and dense fuel at stagnation—in particular, the hotspot pressure, temperature, and areal density. We describe a simple 1D isobaric model to derive these quantities from experimental observables and examine where current experiments lie with respect to the conditions required for ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mixing in ICF implosions on the National Ignition Facility caused by the fill-tube

The micrometer-scale tube that fills capsules with thermonuclear fuel in inertial confinement fusion experiments at the National Ignition Facility is also one of the implosion's main degradation sources. It seeds a perturbation that injects the ablator material into the center, radiating away some of the hot-spot energy. This paper discusses how the perturbation arises in experiments using high-density carbon ablators and how the ablator mix interacts once it enters the hot-spot. Both modeling and experiments show an in-flight areal-density perturbation and localized x-ray emission at stagnation from the fill-tube. Simulations suggest that the fill-tube is degrading an otherwise 1D implosion by ~2×, but when other degradation sources are present, the yield reduction is closer to 20%. Characteristics of the fill-tube assembly, such as the through-hole size and the glue mass, alter the dynamics and magnitude of the degradation. Overall, these aspects point the way toward improvements in the design, some of which (smaller diameter fill-tube) have already shown improvements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Review of hydrodynamic instability experiments in inertially confined fusion implosions on National Ignition Facility

Hydrodynamic instabilities are a major factor in degradation of inertial confinement fusion (ICF) implosions. In the highest performing implosions on National Ignition Facility, yield amplification (YA) due to alpha particle heating approached ~3, while YA of ~15–30 is needed for ignition. Understanding and mitigation of the instabilities are critical to achieving ignition. This article reviews several experimental platforms that have been developed to directly measure these instabilities in all phases of ICF implosions. Measurements of ripple-shock propagation at OMEGA laser has provided results on initial seeds for the instabilities in three ablators—plastic (CH), beryllium, and high-density carbon. Additionally, at the ablation front, instability growth of pre-imposed modulations was measured in the linear regime using the hydrodynamic growth radiography platform. This platform was extended for modulation growth of 'native roughness' modulations and engineering features (fill tubes and capsule support membranes or 'tents'). Several new experimental platforms have or are being developed to measure instability growth at the ablator–ice interface. In the deceleration phase of implosions, complementary 'self-emission' and 'self-backlighting' platforms were developed to measure low-mode asymmetries and high-mode perturbations near peak compression.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Three-dimensional modeling and hydrodynamic scaling of National Ignition Facility implosions

The goal of an inertially confined, igniting plasma on the National Ignition Facility (NIF) [M. L. Spaeth, Fusion Sci. Technol. 69, 25 (2016)] remains elusive. However, there is a growing understanding of the factors that appear to be limiting current implosion performance. And with this understanding, the question naturally arises: What conditions will ultimately be required to achieve ignition, either by continuing to improve the quality of current implosions, or by hydrodynamically scaling those implosions to larger driver energies on some future facility? Given the complexity of NIF implosions, answering this question must rely heavily on sophisticated numerical simulations. In particular, those simulations must respect the three-dimensionality of real NIF implosions and also resolve the wide range of scales for the many perturbation sources that degrade them. This prospectus article reviews the current state of detailed modeling of NIF implosions, the scaling to ignition from recent experiments that that modeling implies, and areas for future improvements in modeling technique that could increase understanding and further enhance predictive capabilities. Furthermore, given the uncertainties inherent in any extrapolation, particularly for a process as nonlinear as ignition, there will be no definitive answer on the requirements for ignition until it is actually demonstrated experimentally. However, with continuing improvements in modeling technique and a growing experience base from NIF, the requirements for ignition are becoming clearer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Modeling and projecting implosion performance for the National Ignition Facility

Steady progress is being made in inertial confinement fusion experiments at the National Ignition Facility (NIF). Nonetheless, substantial further progress is still needed to reach the ultimate goal of fusion ignition. Closing the remaining gap will require either improving the quality of current implosions, increasing the implosion scale (and correspondingly the energy delivered by NIF), or some combination of the two. But how much of an improvement in implosion quality or energy scale is required to reach ignition? To reliably answer this question, an accurate understanding of current and past experiments is first required. Previous modeling efforts of NIF implosions have shown the need to resolve a wide range of scales (from microns to millimeters) as well as a faithful representation of the genuinely three-dimensional (3D) character of the stagnation process. Modeling NIF implosions is further complicated by the many perturbation sources that have been found to influence integrated implosion performance: flux asymmetries from the surrounding hohlraum, engineering features such as support tents and fill tubes, surface defects and contaminants, and more recently the radiation shadow cast by the fill tube on the capsule. A model including all of these effects, and with adequate resolution, challenges current computing capabilities but has recently become feasible on the largest computers. Here, we review the status of these multi-effect, 3D simulations of NIF implosions, their comparison to experimental data, and preliminary results on scaling these simulations to the threshold of ignition on NIF.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗