Engineering topics
Publications and source records attributed to Weber, J. A..
Recommendations are made for improved aerodynamic models and numerical schemes to be considered for inclusion into the FLEXSTAB computer program system. These recommendations are based on a critical analysis of numerical technology.
The application of a higher-order subsonic potential flow panel method to the solution of three-dimensional flow about wing and wing-body combinations with leading-edge vortex separation is presented. The governing equations are the linear flow differential equation and nonlinear boundary conditions which require that the flow be parallel to the wing and body surfaces and that the free vortex sheet, springing from the leading and trailing edges, be aligned with the local flow and support no pressure jump. The vortex core is modeled as a simple line vortex which receives vorticity from the free sheet through a connecting sheet. The Kutta condition is imposed on all appropriate edges of the wing. This set of nonlinear equations is solved by an iterative procedure. The Goethert rule accounts for compressibility. The method has been programmed for the CDC 6600. Delta wings, gothic wings, arrow wings, cambered wings, and wing with body have been analyzed. Initial studies involving variations of panel density, vortex sheet sizing, Jacobian update, and initial geometry demonstrate that the present method generally exhibits good convergence characteristics.
A method of predicting forces, moments, and detailed surface pressures on thin, sharp-edged wings with leading-edge vortex separation in incompressible flow is presented. The method employs an inviscid flow model in which the wing and the rolled-up vortex sheets are represented by piecewise, continuous quadratic doublet sheet distributions. The Kutta condition is imposed on all wing edges. Computed results are compared with experimental data and with the predictions of the leading-edge suction analogy for a selected number of wing planforms over a wide range of angle of attack. These comparisons show the method to be very promising, capable of producing not only force predictions, but also accurate predictions of detailed surface pressure distributions, loads, and moments.
The application of a new, general, potential flow computational technique to the solution of the subsonic, three-dimensional flow over wings with leading-edge vortex separation is presented. The present method is capable of predicting forces, moments, and detailed surface pressures on thin, sharp-edged wings of rather arbitrary planform. The wing geometry is arbitrary in the sense that leading and trailing edges may be curved or kinked and the wing may have arbitrary camber and twist. The method employs an inviscid flow model in which the wing, the rolled-up vortex sheets, and the wake are represented by piecewise continuous quadratic doublet sheet distributions. The Kutta condition is imposed along all wing edges. Strengths of the doublet distributions as well as shape and position of the free fortex sheet spirals are computed in iterative fashion starting with an assumed initial sheet geometry. The method is verified by numerous computed results.
A numerical lifting surface formulation, including computed results for planar wing cases is presented. This formulation, referred to as the vortex spline scheme, combines the adaptability to complex shapes offered by paneling schemes with the smoothness and accuracy of loading function methods. The formulation employes a continuous distribution of singularity strength over a set of panels on a paneled wing. The basic distributions are independent, and each satisfied all the continuity conditions required of the final solution. These distributions are overlapped both spanwise and chordwise. Boundary conditions are satisfied in a least square error sense over the surface using a finite summing technique to approximate the integral. The current formulation uses the elementary horseshoe vortex as the basic singularity and is therefore restricted to linearized potential flow. As part of the study, a non planar development was considered, but the numerical evaluation of the lifting surface concept was restricted to planar configurations. Also, a second order sideslip analysis based on an asymptotic expansion was investigated using the singularity spline formulation.
A new numerical formulation with computed results, is presented. This formulation combines the adaptability to complex shapes offered by paneling schemes with the smoothness and accuracy of the loading function methods. The formulation employs a continuous distribution of singularity strength over a set of panels on a paneled wing. The basic distributions are independent, and each satisfies all of the continuity conditions required of the final solution. These distributions are overlapped both spanwise and chordwise (termed 'spline'). Boundary conditions are satisfied in a least square error sense over the surface using a finite summing technique to approximate the integral.