Dehydrogenative Coupling of Methanol for the Gas-Phase, One-Step Synthesis of Dimethoxymethane over Supported Copper Catalysts
Not Available
Engineering topics
Publications and source records attributed to Wegener, Evan C..
Not Available
In this study, we show how strong metal–support interaction (SMSI) oxides in Pt–Nb/SiO 2 and Pt–Ti/SiO 2 affect the electronic, geometric and catalytic properties for propane dehydrogenation. Transmission electron microscopy (TEM), CO chemisorption, and decrease in the catalytic rates per gram Pt confirm that the Pt nanoparticles were partially covered by the SMSI oxides. X-ray absorption near edge structure (XANES), in situ X-ray photoelectron spectroscopy (XPS), and resonant inelastic X-ray scattering (RIXS) showed little change in the energy of Pt valence orbitals upon interaction with SMSI oxides. The catalytic activity per mol of Pt for ethylene hydrogenation and propane dehydrogenation was lower due to fewer exposed Pt sites, while turnover rates were similar. The SMSI oxides, however, significantly increase the propylene selectivity for the latter reaction compared to Pt/SiO 2 . In the SMSI catalysts, the higher olefin selectivity is suggested to be due to the smaller exposed Pt ensemble sites, which result in suppression of the alkane hydrogenolysis reaction; while the exposed atoms remain active for dehydrogenation.
Layered double hydroxides (LDHs) are an ideal platform to host catalytic metal centers for water oxidation (WO) owing to the high accessibility of water to the interlayer region, which makes all centers potentially reachable and activated. In this paper, we report the syntheses of three iridium-doped zinc–aluminum LDHs (Ir-LDHs) nanomaterials (1–3, with about 80 nm of planar size and a thickness of 8 nm as derived by field emission scanning electron microscopy and powder X-ray diffraction studies, respectively), carried out in the confined aqueous environment of reverse micelles, through a very simple and versatile procedure. These materials exhibit excellent catalytic performances in WO driven by NaIO 4 at neutral pH and 25 °C, with an iridium content as low as 0.5 mol % (~0.8 wt %), leading to quantitative oxygen yields (based on utilized NaIO 4 , turnover number up to ~10,000). Nanomaterials 1–3 display the highest ever reported turnover frequency values (up to 402 min –1 ) for any heterogeneous and heterogenized catalyst, comparable only to those of the most efficient molecular iridium catalysts, tested under similar reaction conditions. The boost in activity can be traced to the increased surface area and pore volume (>5 times and 1 order of magnitude, respectively, higher than those of micrometric materials of size 0.3–1 μm) estimated for the nanosized particles, which guarantee higher noble metal accessibility. X-ray absorption spectroscopy (XAS) studies suggest that 1–3 nanomaterials, as-prepared and after catalysis, contain a mixture of isolated, single octahedral Ir(III) sites, with no evidence of Ir–Ir scattering from second-nearest neighbors, excluding the presence of IrO 2 nanoparticles. The combination of the results obtained from XAS, elemental analysis, and ionic chromatography strongly suggests that iridium is embedded in the brucite-like structure of LDHs, having four hydroxyls and two chlorides as first neighbors. These results demonstrate that nanometric LDHs can be successfully exploited to engineer efficient WOCs, minimizing the amount of iridium used, consistent with the principle of the noble-metal atom economy.
Alloying is well-known to improve the dehydrogenation selectivity of pure metals, but there remains considerable debate about the structural and electronic features of alloy surfaces that give rise to this behavior. To provide molecular-level insights into these effects, a series of Pd intermetallic alloy catalysts with Zn, Ga, In, Fe and Mn promoter elements was synthesized, and the structures were determined using in situ X-ray absorption spectroscopy (XAS) and synchrotron X-ray diffraction (XRD). The alloys all showed propane dehydrogenation turnover rates 5–8 times higher than monometallic Pd and selectivity to propylene of over 90%. Moreover, among the synthesized alloys, Pd 3 M alloy structures were less olefin selective than PdM alloys which were, in turn, almost 100% selective to propylene. This selectivity improvement was interpreted by changes in the DFT-calculated binding energies and activation energies for C–C and C–H bond activation, which are ultimately influenced by perturbation of the most stable adsorption site and changes to the d-band density of states. Furthermore, transition state analysis showed that the C–C bond breaking reactions require 4-fold ensemble sites, which are suggested to be required for non-selective, alkane hydrogenolysis reactions. These sites, which are not present on alloys with PdM structures, could be formed in the Pd 3 M alloy through substitution of one M atom with Pd, and this effect is suggested to be partially responsible for their slightly lower selectivity.
Organometallic iridium catalysts can be used in conjunction with bispinacolatodiboron (B 2 Pin 2 ) to effect the borylation of a variety of substrates such as arenes, alkanes, heteroarenes, and oxygenates. Recently, efforts have also focused on integrating these catalysts into porous supports, such as metal–organic frameworks (MOFs). While the mechanism of homogeneous borylation systems has been thoroughly investigated experimentally and computationally, analogous studies in MOF-supported iridium catalysts have not been conducted. In this paper, we report the mechanistic investigation of a phenanthroline-iridium catalyst immobilized in the organic linker of Universitetet i Oslo (UiO)-67 (Zr 6 O 4 (OH) 4 (BPDC) 4 (PhenDC) 2 , BPDC = biphenyl-4,4'-dicarboxylate, PhenDC = 1,10-phenanthroline-4,4'-dicarboxylate). By using benzene as a model substrate, variable time normalization analysis (VTNA) of the kinetic data suggested a rate law consistent with zero-order in B 2 Pin 2 , and first-order in arene. A primary kinetic isotope effect (KIE) in the time course of benzene-d 6 borylation also provided complementary information about the role of the arene in the rate-determining step of the reaction. Characterization by techniques such as X-ray absorption spectroscopy (XAS) confirmed the presence of Ir(III), while pair distribution function (PDF) analysis suggested structures containing an Ir–Cl bond, further substantiated by X-ray photoelectron spectroscopy (XPS). Analysis of postcatalysis materials by inductively coupled plasma–optical emission spectroscopy (ICP-OES) revealed low boron accumulation, which may indicate an absence of boron in the resting state of the catalyst. Finally, in comparing borylation of benzene and toluene, a slight selectivity for benzene is observed, which is similar to the analogous homogeneous reaction, indicating the influence of substrate sterics on reactivity.
Olefin metathesis is a broadly employed reaction with applications that range from fine chemicals to materials and petrochemicals. The design and investigation of olefin metathesis catalysts have been ongoing for over half a century, with advancements made in terms of activity, stability, and selectivity. Immobilization of organometallic complexes onto solid supports such as silica or alumina is a promising strategy for catalyst heterogenization, often resulting in increased activity and stability. Consequently, a broad range of early transition metal catalysts bearing alkyl, oxide/alkoxide, and amide ligands have been grafted onto silica and their reactivities investigated. In this paper, we report a series of silica-supported tungsten and molybdenum dimers (X 3 M≡MX 3, where M = W and Mo; X = neopentyl, tert-butoxide, and dimethyl amide) and their reactivities toward catalytic olefin metathesis. Dynamic nuclear polarization (DNP)-enhanced solid-state nuclear magnetic resonance (SSNMR), diffuse reflectance infrared Fourier transform (DRIFT), UV resonance Raman, and X-ray absorption (XAS) spectroscopies suggest that upon heterogenization the dimers bind to the surface in a monopodal fashion, with the M≡M triple bond remaining intact. These structural assignments were further corroborated by density functional theory (DFT) calculations. While the homogeneous dimer counterparts are inert, the supported low-valent alkyl W and Mo dimers become active for the disproportionative self-metathesis of propylene to ethylene and butenes and 4-nonene to 4-octene and 5-decene under mild conditions. The lack of activity observed for the free and supported tert-butoxide and dimethyl amide dimers likely suggests that the neopentyl groups are necessary for the formation of a putative alkylidene active species. The difference in reactivity between the free and supported dimers could be explained either by the lowering of the activation barrier of the complex through the electronic effects of the surface or by site isolation of catalytically relevant reactive intermediates.
An integrated experimental and computational study to understand the catalytic upgrading of biomass vapors into high yield of alkenes.
Understanding the mechanisms of action for base metal catalysis of transformations typically associated with precious metals is essential for the design of technologies for a sustainable energy economy. Isolated transition-metal and post-transition-metal catalysts on oxides such as silica are generally proposed to effect hydrogenation and dehydrogenation by a mechanism featuring either σ-bond metathesis or heterolytic bond cleavage as the key bond activation step. In this work, an organovanadium(III) complex on silica, which is a precatalyst for both olefin hydrogenation and alkane dehydrogenation, is interrogated by a series of reaction kinetics and isotopic labeling studies in order to shed light on the operant mechanism for hydrogenation. The kinetic dependencies of the reaction components are potentially consistent with both the σ-bond metathesis and the heterolytic bond activation mechanisms; however, a key deuterium incorporation experiment definitively excludes the simple σ-bond metathesis mechanism. Alternatively, a two-electron redox cycle, rarely invoked for homologous catalyst systems, is also consistent with experimental observations. Evidence supporting the formation of a persistent vanadium(III) hydride upon hydrogen treatment of the as-prepared material is also presented.
Inverse bimetallic catalysts (IBCs), synthesized by sequential deposition of noble and oxophilic metals, offer potential reactivity enhancements to various reactions, including the reduction of carboxylic acids for renewable fuels and chemicals. Here, we demonstrate that an IBC comprising RuSn exhibits high selectivity for propionic acid reduction to 1-propanol, while Ru alone results in cracking. On RuSn, X-ray absorption spectroscopy identified Ru o nanoparticles with a near-surface bimetallic Ru o Sn o alloy and small SnO x domains. Corresponding model surfaces were examined with density functional theory to elucidate the observed selectivity difference. Only selective hydrogenation is predicted to be favorable on SnO x /Ru, with the SnO x clusters facilitating C-OH scission and Ru enabling hydrogen activation. Intrinsic barriers along nonselective pathways suggest that the RuSn alloy and SnO x resist cracking. SnO x /Ru hydrogenation activity was supported experimentally by inhibiting hydrogenation with phenylphosphonic acid, differentiating the system from fully alloyed RuSn metallic nanoparticles. Altogether, this work demonstrates a plausible mechanism for selective reduction of carboxylic acids and proposes a roadmap for rational design of IBCs.
Single-site supported organometallic catalysts bring together the favorable aspects of homogeneous and heterogeneous catalysis while offering opportunities to investigate the impact of metal-support interactions on reactivity. We report a ( dm Phebox)Ir(III) ( dm Phebox = 2,6-bis(4,4-dimethyloxazolinyl)-3,5-dimethylphenyl) complex chemisorbed on sulfated zirconia, the molecular precursor for which was previously applied to hydrocarbon functionalization. Spectroscopic methods such as diffuse reflectance infrared Fourier transformation spectroscopy (DRIFTS), dynamic nuclear polarization (DNP)-enhanced solid-state nuclear magnetic resonance (SSNMR) spectroscopy, and X-ray absorption spectroscopy (XAS) were used to characterize the supported species. Tetrabutylammonium acetate was found to remove the organometallic species from the surface, enabling solution-phase analytical techniques in conjunction with traditional surface methods. Cationic character was imparted to the iridium center by its grafting onto sulfated zirconia, imbuing high levels of activity in electrophilic C–H bond functionalization reactions such as the stoichiometric dehydrogenation of alkanes, with density functional theory (DFT) calculations showing a lower barrier for β–H elimination. Catalytic hydrogenation of olefins was also facilitated by the sulfated zirconia-supported ( dm Phebox)Ir(III) complex, while the homologous complex on silica was inactive under comparable conditions.
Development of platinum group metal (PGM)-free catalysts for oxygen reduction reaction (ORR) is essential for affordable proton exchange membrane fuel cells. Herein, a new type of atomically dispersed Co doped carbon catalyst with a core–shell structure has been developed via a surfactant-assisted metal–organic framework approach. The cohesive interactions between the selected surfactant and the Co-doped zeolitic imidazolate framework (ZIF-8) nanocrystals lead to a unique confinement effect. During the thermal activation, this confinement effect suppressed the agglomeration of Co atomic sites and mitigated the collapse of internal microporous structures of ZIF-8. Among the studied surfactants, Pluronic F127 block copolymer led to the greatest performance gains with a doubling of the active site density relative to that of the surfactant-free catalyst. According to density functional theory calculations, unlike other Co catalysts, this new atomically dispersed Co–N–C@F127 catalyst is believed to contain substantial CoN 2+2 sites, which are active and thermodynamically favorable for the four-electron ORR pathway. The Co–N–C@F127 catalyst exhibits an unprecedented ORR activity with a half-wave potential (E 1/2 ) of 0.84 V (vs. RHE) as well as enhanced stability in the corrosive acidic media. It also demonstrated high initial performance with a power density of 0.87 W cm–2 along with encouraging durability in H 2 –O 2 fuel cells. The atomically dispersed Co site catalyst approaches that of the Fe–N–C catalyst and represents the highest reported PGM-free and Fe-free catalyst performance.
Abstract not provided
Not Available
Developing methods to create hybrid materials to maximize their transformative capabilities has been the subject of significant interest. In particular, several key methods have been developed to manipulate earth abundant metal oxides such as TiO 2 to produce hybrid materials with improved or new properties relevant to a broad spectrum of applications. Here, we introduce a new approach we refer to as “molecular doping”, whereby a hybrid molecular boron oxide material is formed from polyhedral boron cluster precursors of the type [B 12 (OH) 12 ] 2- . This new approach is enabled by the inherent robustness of the boron cluster molecular building block, which is compatible with harsh thermal and oxidizing conditions that are necessary for the synthesis of many metal oxides. In this work, we show how this material can be successfully interfaced with TiO 2 , resulting in boron-rich hybrid materials with unprecedented photophysical and electrochemical properties.
Oxygen evolution reaction (OER) is a pivotal process in many energy conversion and storage techniques, such as water splitting, regenerative fuel cells, and rechargeable metal-air batteries. The synthesis of stable, efficient, non-noble metal-based electrocatalysts for OER has been a long-standing challenge. In this work, a facile and scalable method to synthesize hollow and conductive iron–cobalt phosphide (Fe–Co–P) alloy nanostructures using an Fe–Co metal organic complex as a precursor is described. The Fe–Co–P alloy exhibits excellent OER activity with a specific current density of 10 mA/cm 2 being achieved at an overpotential as low as 252 mV. The current density at 1.5 V (vs reversible hydrogen electrode) of the Fe–Co–P catalyst is 30.7 mA/cm 2 , which is more than 3 orders of magnitude greater than that obtained with state-of-the-art Fe–Co oxide catalysts. Our mechanistic experiments and theoretical analysis suggest that the electrochemical-induced high-valent iron stabilizes the cobalt in a low-valent state, leading to the simultaneous enhancement of activity and stability of the OER catalyst.
Thiol-amine mixtures are an attractive medium for the solution processing of semiconducting thin films because of their remarkable ability to dissolve a variety of metals, metal chalcogenides, metal salts, and chalcogens. However, very little is known about their dissolution chemistry. Electrospray ionization high-resolution tandem mass spectrometry and X-ray absorption spectroscopy were employed in this study to identify the species formed upon dissolution of CuCl and CuCl 2 in 1-propanethiol and n -butylamine. Copper was found to be present exclusively in the 1+ oxidation state for both solutions. The copper complexes detected include copper chlorides, copper thiolates, and copper thiolate chlorides. No complexes of copper with amines were observed. Additionally, alkylammonium ions and alkylammonium chloride adducts were observed. These findings suggest that the dissolution is initiated by proton transfer from the thiol to the amine, followed by coordination of the thiolate anions with copper cations. Interestingly, the mass and X-ray absorption spectra of the solutions of CuCl and CuCl 2 in thiol-amine were essentially identical. However, dialkyl disulfides were identified by Raman spectroscopy as an oxidation product only for the copper(II) solution, wherein copper(II) had been reduced to copper(I). Analysis of several thiol-amine pairs suggested that the dissolution mechanism is quite general. Finally, analysis of thin films prepared from these solutions revealed persistent chlorine impurities, in agreement with previous studies. These impurities are explained by the mass spectrometric finding that chloride ligands are not completely displaced by thiolates upon dissolution. These results suggest that precursors other than chlorides will likely be preferred for the generation of high-efficiency copper chalcogenide films, despite the reasonable efficiencies that have been obtained for films generated from chloride precursors in the past.
The structure of silica supported Pt and Pt-In bimetallic catalysts with nominal In: Pt atomic ratios of 0.7 and 1.4 were here determined by in situ synchrotron XAS and XRD. It was seen that the addition of In led to the formation of two different intermetallic alloy phases. At an In: Pt ratio of 0.7 the Pt 3 In phase with a Cu 3 Au structure was formed. When the ratio was increased to 1.4 a shell of PtIn 2 having a CaF 2 structure formed around a core of Pt 3 In. The catalysts were tested for ethane dehydrogenation at 600° to determine the effect of alloying on ethylene selectivity and turnover rate (TOR). The monometallic Pt catalysts was 73% selective for ethylene and had an initial TOR of 0.7 s -1 . Both alloy catalysts were approximate to 100% selective for dehydrogenation and had higher initial TOR, 2.8 s -1 and 1.6 s -1 for In: Pt ratio of 0.7 and 1.4, respectively. The increase in selectivity is attributed to the elimination of large Pt ensembles resulting from geometric changes to the catalyst surface upon alloying. Electronic changes due to the formation of Pt-In bonds are thought to be responsible for the increases in TOR in the alloy catalysts.
A single-site molybdenum dioxo catalyst, (O c ) 2 Mo(=O)2@C, was prepared via direct grafting of MoO 2 Cl 2 (dme) (dme = 1,2-dimethoxyethane) on high-surface-area activated carbon. The physicochemical and chemical properties of this catalyst were fully characterized by N 2 physisorption, ICP-AES/OES, PXRD, STEM, XPS, XAS, temperature-programmed reduction with H 2 (TPR-H 2 ), and temperature-programmed NH 3 desorption (TPD-NH 3 ). The single-site nature of the Mo species is corroborated by XPS and TPR-H2 data, and it exhibits the lowest reported MoO x T max of reduction reported to date, suggesting a highly reactive Mo VI center. (O c ) 2 Mo(=O) 2 @C catalyzes the transesterification of a variety of esters and triglycerides with ethanol, exhibiting high activity at moderate temperatures (60–90 °C) and with negligible deactivation. (O c ) 2 Mo(=O) 2 @C is resistant to water and can be recycled at least three times with no loss of activity. The transesterification reaction is determined experimentally to be first order in [ethanol] and first order in [Mo] with ΔH ‡ = 10.5(8) kcal mol –1 and ΔS ‡ = –32(2) eu. Here, the low energy of activation is consistent with the moderate conditions needed to achieve rapid turnover. This highly active carbon-supported single-site molybdenum dioxo species is thus an efficient, robust, and low-cost catalyst with significant potential for transesterification processes.