Reactive Air Aluminizing of Nicrofer-6025HT for Use in Advanced Coal-Based Power Plants
The present work demonstrated the feasibility of preparing RAA coatings on Nicrofer and compared the effect of aluminum powder size on the RAA process.
Engineering topics
Publications and source records attributed to Weil, K Scott.
The present work demonstrated the feasibility of preparing RAA coatings on Nicrofer and compared the effect of aluminum powder size on the RAA process.
In the present study, the properties of a series of non-platinum based nanoscale tantalum oxide/tungsten oxide-carbon composite catalysts was investigated for potential use in catalyzing the oxygen reduction reaction (ORR) on the cathode side of a PEM fuel cell membrane electrode assembly. Electrochemical performance was measured using a half-cell test set up with a rotating disc electrode and compared with a commercial platinum-on-carbon (Pt/C) catalyst. Overall, all of the oxide-based composite catalysts exhibit high ORR on-set potentials, comparable to that of the baseline Pt/C catalyst. The addition of tungsten oxide as a dopant to tantalum oxide greatly improved mass specific current density. Maximum performance was achieved with a catalyst containing 32 mol% of tungsten oxide, which exhibited a mass specific current density ~8% that of the Pt/C catalyst at 0.6 V vs. the normal hydrogen electrode (NHE) and ~35% that of the Pt/C catalyst at 0.2 V vs. NHE. Results from X-ray photoelectron spectroscopy analysis indicated that the tungsten cations in the composite catalysts exist in the +6 oxidation state, while the tantalum displays an average valence of +5, suggesting that the addition of tungsten likely creates an oxygen excess in the tantalum oxide structure that influences its oxygen absorption kinetics. When the 32mol% tungsten doped catalyst loading on the working electrode was increased to five times that of the original loading (which was equivalent to that of the baseline Pt/C catalyst), the area specific current density improved four fold, achieving an area specific current density ~35% that of the Pt/C catalyst at 0.6 V vs. NHE.
Precious-metal catalysts (predominantly Pt or Pt-based alloys supported on carbon) have traditionally been used to catalyze the electrode reactions in polymer electrolyte membrane (PEM) fuel cells. However as PEM fuel systems begin to approach commercial reality, there is an impending need to replace Pt with a lower cost alternative. The present study investigates the performance of a carbon-supported tantalum oxide material as a potential oxygen reduction reaction (ORR) catalyst for use on the cathode side of the PEM fuel cell membrane electrode assembly. Although bulk tantalum oxide tends to exhibit poor electrochemical performance due to limited electrical conductivity, it displays a high oxygen reduction potential; one that is comparable to Pt. Analysis of the Pourbaix electrochemical equilibrium database also indicates that tantalum oxide (Ta2O5) is chemically stable under the pH and applied potential conditions to which the cathode catalyst is typically exposed during stack operation. Nanoscale tantalum oxide catalysts were fabricated using two approaches, by reactive oxidation sputtering and by direct chemical synthesis, each carried out on a carbon support material. Nanoscale tantalum oxide particles measuring approximately 6nm in size that were sputtered onto carbon paper exhibited a mass-specific current density as high as one-third that of Pt when measured at 0.6V vs. NHE. However because of the two-dimensional nature of this particle-on-paper structure, which limits the overall length of the triple phase boundary junctions where the oxide, carbon paper, and aqueous electrolyte meet, the corresponding area-specific current density was quite low. The second synthesis approach yielded a more extended, three-dimensional structure via chemical deposition of nanoscale tantalum oxide particles on carbon powder. These catalysts exhibited a high ORR onset potential, comparable to that of Pt, and displayed a significant improvement in the area-specific current density. Overall, the highest mass-specific current density of the carbon-powder supported catalyst was ~ 9% of that of Pt.
Low-cost, chromia-forming steels find widespread use in SOFCs at operating temperatures below 800°C, because of their low thermal expansion mismatch and low cost. However, volatile Cr-containing species originating from this scale poison the cathode material in the cells and subsequently cause power degradation in the devices. To prevent this, a conductive manganese cobaltite coating has been developed. However, this coating is not compatible with forming hermetic seals between the interconnect or window frame component and ceramic cell. This coating reacts with sealing materials. Thus, a new aluminizing process has been developed for the sealing regions in these parts, as well as for other metallic stack and balance-of-plant components. From this development, the sealing performance and SOFC stack performance became very stable.
A joint for use in electrochemical devices, such as solid oxide fuel cells (SOFCs), oxygen separators, and hydrogen separators, that will maintain a hermetic seal at operating temperatures of greater than 600.degree. C., despite repeated thermal cycling excess of 600.degree. C. in a hostile operating environment where one side of the joint is continuously exposed to an oxidizing atmosphere and the other side is continuously exposed to a wet reducing gas. The joint is formed of a metal part, a ceramic part, and a flexible gasket. The flexible gasket is metal, but is thinner and more flexible than the metal part. As the joint is heated and cooled, the flexible gasket is configured to flex in response to changes in the relative size of the metal part and the ceramic part brought about by differences in the coefficient of thermal expansion of the metal part and the ceramic part, such that substantially all of the tension created by the differences in the expansion and contraction of the ceramic and metal parts is absorbed and dissipated by flexing the flexible gasket.
The Ag-CuOx system is being investigated as potential filler metals for use in air brazing high-temperature electrochemical devices such as solid oxide fuel cells and gas concentrators. The current study examines the effects of palladium addition on the high temperature joint strength of specimens prepared from yttria stabilized zirconia (YSZ) bars brazed with the binary Ag-CuOx, and 15Pd-Ag-CuO. It was found that while the binary Ag-CuOx system exhibits stronger room temperature strength than the 15Pd system the strength is reduced to values equivalent of the 15Pd system at 800°C. The 15Pd system exhibits a lower ambient temperature strength that is retained at 800°C. In both systems the failure mechanism at high temperature appears to be peeling of the noble metal component from the oxide phases and tearing through the noble metal phase whereas sufficient adhesion is retained at lower temperatures to cause fracture of the YSZ substrate.
Niobium (Nb)-clad 304L stainless steel (SS) manufactured by cold rolling is currently under consideration for use as a bipolar plate material in polymer electrolyte membrane fuel cell (PEMFC) stacks. To make the fabrication of bipolar plates using the Nb-clad SS feasible, annealing may be necessary for the Nb-clad SS to reduce the springback induced by cold rolling. However, the annealing can develop an interfacial layer between the Nb cladding and the SS core and the interfacial layer plays a key role in the failure of the Nb-clad SS as reported earlier [JPS our work]. In this investigation, the Nb-clad SS specimens in as-rolled condition were annealed at different combinations of temperature and time. Based on the results of scanning electron microscope (SEM) analysis, an annealing process map for the Nb-clad SS was obtained. The results of SEM analysis and Transmission Electron Microscope (TEM) analysis also suggest that different interfacial layers occurred based on the given annealing conditions.
A reliable, cost-effective high-temperature sealing technology for the joining of ceramic components to metallic structures is critical to the successful development of solid oxide fuel cells (SOFCs). In this paper, our latest development of a novel reactive air brazing (RAB) technology will be presented. This RAB technology uses Ag-CuO as the base braze composition with a variety of additional elements. With a proper processing control, the resultant sealing technology is capable of providing a high-temperature sealing with sufficient chemical inertness, thermal reliability, and bonding strength. We will present in this paper our latest studies on the composition design/synthesis of braze filler materials, and the characterizations including wettability, microstructure, and mechanical properties, as well as a preliminary numerical simulation addressing the residual stress generated during the processing.
A simple strategy for covalently attaching Ta2O5 particles onto functionalized graphitic carbon supports has been developed to fabricate hybrid nanocomposites. In this process, tantalum ethoxide was directly reacted with functional groups on the carbon surface to form covalent bonding, which caused the carbonyl stretches of the carbon supports to be blue-shifted to 50-70 cm-1 after Ta2O5 particle deposition. Homogeneously distributed Ta2O5 particles with smaller than 100 nm have been homogeneously deposited on the carbon supports. X-ray diffraction (XRD), FT-IR spectroscopy, and scanning electron microscopy (SEM) have been used to study the formation of Ta2O5/C hybrid structure.