Search NASA⌕ Search

Engineering topics

Weisgraber, Todd H.

Publications and source records attributed to Weisgraber, Todd H..

At least 19 records

Novel Fast Cure Silicone Inks for Single-Step, Support-Free 3D Printing of Tall, Overhanging, and High Aspect Ratio Structures

Silicone elastomers have a broad variety of applications, such as soft robotics, biomedical devices, and structural metamaterials. The extrusion-based method known as direct ink write (DIW) has enabled the production of additively manufactured silicone structures. However, this method is limited to manufacturing mostly planar or pseudo-3D structures. Due to the low self-supporting capabilities of extruded strands for traditional silicone-based “inks,” obtaining tall or overhanging structures, or structures comprised by thin walls is not feasible. Here, in this study, a novel Fast Cure silicone-based ink is demonstrated that enables manufacturing of complex 3D structures. The Fast Cure ink is a two-part mixture and silicone structures are produced by inline mixing and coextrusion of a part containing a catalyst (part A) and a part containing a crosslinker (part B). By the virtue of crosslinking, the extruded strands rapidly rigidize, increasing their self-supportive capacity. Hence, structures can be obtained with superior shape retention and previously unobtainable parts are realized that are tall, with aspect ratios higher than 3, and have overhanging features, achieving inclination angles smaller than 35° with respect to the printing plane. These minimal sag parts are achieved without requiring extra curing or mechanisms, support structures, or suspension baths.

36 MATERIALS SCIENCE↗

Modeling of Sagging for 3D Printed Layers During the Curing Process

Here, a printed layer of silica-enforced poly(dimethylsiloxane)-co-(diphenylsiloxane) is modeled as a two-phase system consisting of air and polymer with an interface set up during the printing process. The structural geometry changes mostly due to the action of surface tension, while all material properties are strongly temperature dependent. Polymer flow is described using equations of the extended Herschel–Bulkley model, with parameters strongly dependent on temperature and degree of curing. Parameters of the model are determined using flow sweep measurements and separate experiments with vertical structure sagging at different temperatures. The curing process is modeled using dependencies between the curing rate, degree of curing, and temperature obtained in studies by differential scanning calorimetry. The developed model is used for simulations of printed structure deformations with different initial and boundary conditions.

36 MATERIALS SCIENCE↗

Controlled In Situ Foaming for Mechanical Responsiveness of Architected Foams

Addition of chemical blowing agents to polysiloxane resins produces foams with closed–cell morphology. Combining this chemistry with the 3D–printing technique direct ink writing (DIW) permits the creation of architected foams with controllable, hierarchical tiers of porosity. Here, using a two–component foaming ink, the extent of foaming can be controlled by incorporating an active mixing printhead as part of the fabrication process. Changes in the mixing speed allows for in situ control of the foaming reaction where the mixing speed is directly correlated with the resulting foaming that occurs upon extrusion. These architected foams display tunable mechanical responses, porosities, and open–to–closed cell ratios. While chemically blown polysiloxane foam is a well–established material, utilizing DIW as fabrication technique presents a novel approach for creating tailored, architected foams that require minimal post–processing.

36 MATERIALS SCIENCE↗

Virtual Volumetric Additive Manufacturing (VirtualVAM)

Abstract Tomographic volumetric additive manufacturing (VAM) produces arbitrary 3D geometries by exposure of a rotating volume of photopolymer resin to tomographically‐patterned illumination. This enables high speed, layer‐less printing of parts from a wide range of photopolymers not amenable to layer‐by‐layer processes. Since the entire geometry is produced at once over the course of a few seconds to minutes, molecular diffusion length scales become significant to the printing process. Understanding these molecular reaction and diffusion processes is imperative for advancing VAM to a usable technology. These processes are experimentally very difficult to monitor and measure. Herein, VirtualVAM ‐ a simulation framework for modeling the tomographic VAM process, is developed and experimentally validated. VirtualVAM simulates reaction, diffusion, and heat generation processes over the course of a print with single‐voxel resolution. From a few experimentally‐determined input parameters and a set of images for projection, VirtualVAM is able to generate a large spatio‐temporal data set for any given tomographic VAM print. Using VirtualVAM, a number of experimentally‐unattainable aspects of the VAM process are investigated such as single‐voxel conversion profiles, effect of molecular oxygen, and stopping time determination. VirtualVAM also enables the optimization of exposure patterns to further improve contrast between in‐part and out‐of‐part delivered dose.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Isolating Chemical Reaction Mechanism as a Variable with Reactive Coarse-Grained Molecular Dynamics: Step-Growth versus Chain-Growth Polymerization

Here we present a general approach to isolate chemical reaction mechanism as an independently controllable variable across chemically distinct systems. Modern approaches to reduce the computational expense of molecular dynamics simulations often group multiple atoms into a single “coarse-grained” interaction site, which leads to a loss of chemical resolution. In this work we convert this shortcoming into a feature and use identical coarse-grained models to represent molecules that share nonreactive characteristics but react by different mechanisms. As a proof of concept, we use this approach to simulate and investigate distinct, yet similar, trifunctional isocyanurate resin formulations that polymerize by either chain- or step-growth. Because the underlying molecular mechanics of these models are identical, all emergent differences are a function of the reaction mechanism only. We find that the microscopic morphologies resemble related all-atom simulations and that simulated mechanical testing reasonably agrees with experiment.

36 MATERIALS SCIENCE↗

On the Network Topology of Cross-Linked Acrylate Photopolymers: A Molecular Dynamics Case Study

A reactive molecular dynamics approach is used to simulate cross-linking of acrylate polymer networks. By employing the same force field and reactive scheme and studying three representative multifunctional acrylate monomers, we isolate the importance of the nonreactive moieties within these model monomers. Analyses of reactive trajectories benchmark the estimated gel points, cyclomatic character, and spatially resolved cross-linking tendencies of the acrylates as a function of conversion. The insights into the similarities and differences of the polymerization and resulting networks presented here suggest molecular mechanics as a useful tool in the rational design of photopolymerization resins.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Simulating stochastic and additively manufactured foams at large strains and high strain rates

Understanding the mechanical response of polymer foams is essential in developing system material models and in designing replacements for legacy pads and cushions. Simulations can help elucidate structure-property relationships and compare local stress distributions to understand aging behavior and improve designs. In many applications, these materials experience significant loadings and computations need the capability to reproduce those conditions.

36 MATERIALS SCIENCE↗

Simulating stochastic and additively manufactured foams at large strains and high strain rates (Progress Summary)

Understanding the mechanical response of polymer foams is essential in developing system material models and in designing replacements for legacy pads and cushions. Simulations can help elucidate structure-property relationships and compare local stress distributions to understand aging behavior and improve designs. In many applications, these materials experience significant loadings and computations need the capability to reproduce those conditions. We are applying are previously developed material point method (MPM) simulation capability to understand the aging properties of loaded direct ink write resins. Significant particle loading of a stiffer material in siloxane networks exhibit different compression set behavior than unloaded specimens. We are applying our computational mechanics capabilities to understand this difference at the continuum level. Figure 1 highlights preliminary results, depicting renderings of an unloaded DIW filament alongside one containing a 20% volume loading of spherical particles. Also, the stress distribution of a neat filament at 20% compression is shown. We are planning to study this behavior for a range of loading fractions, particle sizes, and material stiffness ratios. We will explore the sensitivity of the stress response to these variables which could inform aging models of these materials.

36 MATERIALS SCIENCE↗

Progress Summary: Simulating stochastic and additively manufactured foams at large strains and high strain rates

Motivation: Understanding the mechanical response of polymer foams is essential in developing system material models and in designing replacements for legacy pads and cushions. Simulations can help elucidate structure-property relationships and compare local stress distributions to understand aging behavior and improve designs. In many applications,these materials experience significant loadings and computations need the capability to reproduce those conditions. Significance: In designing the compressive and shear response of additively manufactured foams, we expect the curvature of the substrate to influence their mechanical behavior. Progress:We have the capability of mapping planar structures to arbitrary curved surfaces and are currently developing the software and procedures to translate the mapped pattern into a geometrical model that can be imported to either finite element or material point software to evaluate the mechanical response. Figure 1 depicts a four-layer face-centered tetragonal pattern (FCT) mapped to a hemispherical surface. Because the mapping cannot exactly preserve both distances and angles, we expect some local variation in mechanical properties and porosity. These models will help determine the sensitivity of these variations to structure and curvature, optimize the mapping procedure, and inform the design of foams for non-planar surfaces.

36 MATERIALS SCIENCE↗

A mechanical reduced order model for elastomeric 3D printed architectures

Direct ink writing of silicone elastomers enables printing with precise control of porosity and mechanical properties of ordered cellular solids, suitable for shock absorption and stress mitigation applications. With the ability to manipulate structure and feedstock stiffness, the design space becomes challenging to parse to obtain a solution producing a desired mechanical response. We derive an analytical design approach for a specific architecture. Results from finite element simulations and quasi-static mechanical tests of two different parallel strand architectures were analyzed to understand the structure-property relationships under uniaxial compression. Combining effective stiffness-density scaling with least squares optimization of the stress responses yielded general response curves parameterized by resin modulus and strand spacing. An analytical expression of these curves serves as a reduced order model, which, when optimized, provides a rapid design capability for filament-based 3D printed structures. Finally, as a demonstration, the optimal design of a face-centered tetragonal architecture is computed that satisfies prescribed minimum and maximum load constraints.

36 MATERIALS SCIENCE↗

One-step volumetric additive manufacturing of complex polymer structures

Two limitations of additive manufacturing methods that arise from layer-based fabrication are slow speed and geometric constraints (which include poor surface quality). Both limitations are overcome in the work reported here, introducing a new volumetric additive fabrication paradigm that produces photopolymer structures with complex non-periodic 3D geometries on a timescale of seconds. We implement this approach using holographic patterning of light fields, demonstrate the fabrication of a variety of structures, and study the properties of the light patterns and photosensitive resins required for this fabrication approach. The results indicate that lowabsorbing resins containing ~0.1% photoinitiator, illuminated at modest powers (~10-100 mW) may be successfully used to build full structures in ~1-10 s.

36 MATERIALS SCIENCE↗

Mesoscale Particle-Based Model of Electrophoretic Deposition

In this paper, we present and evaluate a semiempirical particle-based model of electrophoretic deposition using extensive mesoscale simulations. We analyze particle configurations in order to observe how colloids accumulate at the electrode and arrange into deposits. In agreement with existing continuum models, the thickness of the deposit increases linearly in time during deposition. Resulting colloidal deposits exhibit a transition between highly ordered and bulk disordered regions that can give rise to an appreciable density gradient under certain simulated conditions. The overall volume fraction increases and falls within a narrow range as the driving force due to the electric field increases and repulsive intercolloidal interactions decrease. We postulate ordering and stacking within the initial layer(s) dramatically impacts the microstructure of the deposits. Finally, we find a combination of parameters, i.e., electric field and suspension properties, whose interplay enhances colloidal ordering beyond the commonly known approach of only reducing the driving force.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Universal Design Curves for Elastomeric Direct Ink-Writing Architectures

Direct ink writing of silicone elastomers enables printing with precise control of porosity and mechan- ical properties of ordered cellular solids, suitable for shock absorption and stress mitigation applications. With the ability to manipulate structure and feedstock stiffness, the design space becomes challenging to parse to obtain a solution producing a desired mechanical response. Here we derive an analytical design approach for a specific architecture. Results from finite element simulations and quasi-static mechanical tests of two different parallel strand architectures were analyzed to understand the structure-property relationships under compressive strain. Combining effective stiffness-density scaling with least squares optimization of the stress responses yielded general response curves parameterized by resin modulus and strand spacing. An analytical expression of these curves serves as a reduced order model, which, when optimized, provides a rapid design capability for filament-based 3D printed structures. As a demonstration, the optimal design of a face-centered tetragonal architecture is computed that satisfies prescribed minimum and maximum load constraints.

36 MATERIALS SCIENCE↗

Organizing Cells Within Non-Periodic Microarchitectured Materials That Achieve Graded Thermal Expansions

The aim of this paper is to introduce an approach for optimally organizing a variety of different unit cell designs within a large lattice such that the bulk behavior of the lattice exhibits a desired Young’s modulus with a graded change in thermal expansion over its geometry. This lattice, called a graded microarchitectured material, can be sandwiched between two other materials with different thermal expansion coefficients to accommodate their different expansions or contractions caused by changing temperature while achieving a desired uniform stiffness. First, this paper provides the theory necessary to calculate the thermal expansion and Young’s modulus of large multi-material lattices that consist of periodic (i.e., repeating) unit cells of the same design. Then it introduces the theory for calculating the graded thermal expansions of a large multimaterial lattice that consists of non-periodic unit cells of different designs. An approach is then provided for optimally designing and organizing different unit cells within a lattice such that both of its ends achieve the same thermal expansion as the two materials between which the lattice is sandwiched. A MATLAB tool is used to generate images of the undeformed and deformed lattices to verify their behavior and various examples are provided as case studies. The theory provided is also verified and validated using finite element analysis and experimentation.

Young’s modulus↗

Mesoscale Particle-Based Model of Electrophoresis

Here, we develop and evaluate a semi-empirical particle-based model of electrophoresis using extensive mesoscale simulations. We parameterize the model using only measurable quantities from a broad set of colloidal suspensions with properties that span the experimentally relevant regime. With sufficient sampling, simulated diffusivities and electrophoretic velocities match predictions of the ubiquitous Stokes-Einstein and Henry equations, respectively. This agreement holds for non-polar and aqueous solvents or ionic liquid colloidal suspensions under a wide range of applied electric fields.

36 MATERIALS SCIENCE↗

Interpolation methods and the accuracy of lattice-Boltzmann mesh refinement

A lattice-Boltzmann model to solve the equivalent of the Navier-Stokes equations on adap- tively refined grids is presented. A method for transferring information across interfaces between different grid resolutions was developed following established techniques for finite- volume representations. This new approach relies on a space-time interpolation and solving constrained least-squares problems to ensure conservation. The effectiveness of this method at maintaining the second order accuracy of lattice-Boltzmann is demonstrated through a series of benchmark simulations and detailed mesh refinement studies. These results exhibit smaller solution errors and improved convergence when compared with similar approaches relying only on spatial interpolation. Examples highlighting the mesh adaptivity of this method are also provided.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

FY2011 Engineering Innovations, Research, and Technology Report

This report summarizes key research, development, and technology advancements in Lawrence Livermore National Laboratory’s Engineering Directorate for FY2011. These efforts exemplify Engineering’s nearly 60-year history of developing and applying the technology innovations needed for the Laboratory’s national security missions, and embody Engineering’s mission to “Enable program success today and ensure the Laboratory’s vitality tomorrow.

42 ENGINEERING↗