Engineering topics

Weller, W. H.

Publications and source records attributed to Weller, W. H..

10 records

NASA NTRS1984

Measured and calculated inplane stability characteristics for an advanced bearingless main rotor

A program of experimental and analytical research has been performed to demonstrate the effects of rotor and fuselage design parameters on rotor in-plane stability, including aeromechanical stability. The experimental data were obtained from hover and wind-tunnel tests of a scaled advanced bearingless main rotor model. Both isolated-rotor and free-hub conditions were tested. Test parameters included blade built-in cone and sweep angles; rotor inplane structural stiffness and damping; pitch link stiffness and location; and fuselage natural frequency, damping, and inertia. The results show that rotor blade structural damping is one of the most influential design parameters in obtaining acceptable aeromechanical stability margins. Other parameters, such as blade cone angle, pitch link location (rotor delta 3) and anisotropic hub damper configurations, may be used to improve stability margins, but their individual effects are subtle.

Weller, W. H.↗

NASA NTRS1983

Correlation and evaluation of inplane stability characteristics for an advanced bearingless main rotor

A program of experimental and analytical research was performed to demonstrate the degree of correlation achieved between measured and computed rotor inplane stability characteristics. The experimental data were obtained from hover and wind tunnel tests of a scaled bearingless main rotor model. Both isolated rotor and free-hub conditions were tested. Test parameters included blade built-in cone and sweep angles; rotor inplane structural stiffness and damping; pitch link stiffness and location; and fuselage damping, inertia, and natural frequency. Analytical results for many test conditions were obtained. In addition, the analytical and experimental results were examined to ascertain the effects of the test parameters on rotor ground and air resonance stability. The results from this program are presented herein in tabular and graphical form.

Weller, W. H.↗

NASA NTRS1983

Measured inplane stability characteristics in hover for an advanced bearingless rotor

A study was made of the inplane stability characteristics of a model of an advanced bearingless main rotor. The four-bladed rotor system was tested for aeroelastic stability in hover for both isolated and body-free conditions. Variations in several hub design parameters were tested, including blade coning and sweep angles, blade inplane structural damping, pitch-link location (delta-free effect), and fuselage structural damping. An analysis of the experimental results shows that parametric stability trends observed from isolated-rotor studies may yield incorrect conclusions regarding coupled rotor-body characteristics. For body-free conditions, the baseline rotor configuration resulted in the best stability margins at 1-g thrust as well as at the nominal design rotor speed. Blade built-in coning had little effect on the body-free damping levels at the inplane/body resonance points. Introducing blade sweep destabilized the rotor at the inplane/body pitch resonance.

Weller, W. H.↗

NASA NTRS1982

Correlating measured and predicted inplane stability characteristics for an advanced bearingless rotor

The experimental data were obtained from hover tests for a scaled model of an advanced bearingless main rotor. Both isolated rotor and ground resonance conditions were tested. Test parameters included blade built-in cone and sweep angles, rotor inplane structural damping, pitch link location and fuselage structural damping. Analytical results for the conditions tested were obtained using current Bell Helicopter analyses. In addition, variations in the analytical models were made to assess their impact on the correlation between computed and measured results. Results are presented in tabular and graphical form.

Weller, W. H.↗

NASA NTRS1980

Natural modes of helicopter rotor blades

Computer program based on Holzer-Myklestad approach calculates coupled vertical, horizontal, and torsional characteristics of wide variety of hub and blade configurations of practical interest. Program is written in FORTRAN IV.

Mineck, R. E.↗

NASA NTRS1979

Experimental investigation of effects of blade tip geometry on loads and performance for an articulated rotor system

Wind-tunnel tests of an aeroelastically designed helicopter rotor model were carried out to determine the effects on dynamic response and aerodynamic performance of varying the design of the outboard 8 percent of the blade lengths. Four different blade tip geometries or shapes having different amounts of planform sweep, thickness and chordwise taper, and anhedral angle were studied. Each configuration was tested at several shaft angles of attack for advance ratios of 0.20, 0.30, 0.35, and 0.40. For each combination of shaft angle and advance ratio, rotor lift was varied over a wide range to include high lift conditions.

Weller, W. H.↗

NASA NTRS1978

An improved computational procedure for determining helicopter rotor blade natural modes

An existing computer program, used for predicting the natural frequencies and mode shapes of helicopter rotor blades, was refined to improve program accuracy and versatility. The program is based on the Holzer-Myklestad approach adapted for rotating beams. Coupled vertical (out-of-plane), horizontal (in-plane), and torsional mode characteristics were determined for a variety of hub and blade configurations. The resulting program is documented by presenting the recursion equations and techniques for determining natural frequencies and mode shapes, input data requirements, and descriptions of various program outputs. The accuracy of the program is demonstrated by comparing computed results with exact solutions to classical problems and experimental data.

Weller, W. H.↗

NASA NTRS1978

Comparison of aerodynamic data measured in air and Freon-12 wind-tunnel test mediums

An experimental investigation was carried out to measure two dimensional static aerodynamic characteristics of a 65 sub l-213 airfoil in air and Freon-12 (dichlorodifluoromethane) test mediums at corresponding test conditions. The purpose of the tests was to compare measurements in the two test mediums and to evaluate reported methods of converting Freon-12 data to equivalent air values. The test article was a two dimensional wing instrumented to measure chordwise surface pressure distributions. The parameters considered were Mach numbers from 0.6 to 1.0, angles of attack of zero deg and 1 deg, and Reynolds numbers based on model chord from 2,000,000 to 21,000,000. The agreement between data measured in the two test mediums is further improved by application of the transonic or area ratio similarity laws. Where flow conditions are characterized by surface shocks or stall, the effects of flow separation may not be identically reflected in the Freon-12 data, even when converted in accordance with existing similarity laws.

Weller, W. H.↗

NASA NTRS1977

Wind-tunnel tests of wide-chord teetering rotors with and without outboard flapping hinges

Wind tunnel tests of aeroelastically designed helicopter rotor models were conducted to obtain rotor aerodynamic performance and dynamic response data pertaining to two-bladed teetering rotors with a wider chord and lower hover tip speed than currently employed on production helicopters. The effects of a flapping hinge at 62 percent radius were also studied. Finally, the effects of changing tip mass on operating characteristics of the rotor with the outboard flapping hinge were examined. The models were tested at several shaft angles of attack for five advance ratios, 0.15, 0.25, 0.35, 0.40, and 0.45. For each combination of shaft angle and advance ratio, the rotor lift was varied over a wide range to include simulated maneuver conditions. At each test condition, rotor aerodynamic performance and dynamic response data were obtained. From these tests, it was found that wide-chord rotors may be subject to large control forces. An outboard flapping hinge may be used to reduce beamwise bending moments over a significant part of the blade radius without significantly affecting the chordwise bending moments.

Weller, W. H.↗

NASA NTRS1977

Load and stability measurements on a soft-inplane rotor system incorporating elastomeric lead-lag dampers

An experimental investigation was conducted of the dynamic response and inplane stability associated with a new soft-inplane helicopter rotor. The unique feature of this rotor was the use of an internal elastomeric damper to restrain the blade inplane motion about the lead-lag hinge. The properties of the elastomer were selected to provide both a nominal first inplane frequency ratio of 0.65 and sufficient damping to eliminate the need for additional external damping sources to prevent ground resonance on a typical fuselage structure. For this investigation a 1/5-scale aeroelastic model was used to represent the rotor. The four-blade model had a diameter of 3.05 m (10 ft) and a solidity of 0.103. The first out-of-plane frequency ratio was 1.06. The model was tested in hover and in forward flight up to an advance ratio of 0.45. At each forward speed the rotor lift was varied up to simulated maneuver conditions. The measured rotor loads and response were within acceptable limits, and no adverse response qualities were observed. Moderate out-of-plane hub moments were measured, even for zero lift, to indicate the beneficial control power available for this design. Blade inplane stability testing indicated that the rotor system damping remained at moderate levels throughout the operating envelope.

Weller, W. H.↗