Engineering topics

Wells, William L.

Publications and source records attributed to Wells, William L..

8 records

NASA NTRS1993

Hypersonic lateral and directional stability characteristics of aeroassist flight experiment configuration in air and CF4

Hypersonic lateral and directional stability characteristics measured on a 60 deg half-angle elliptical cone, which was raked at an angle of 73 deg from the cone centerline and with an ellipsoid nose (ellipticity equal to 2.0 in the symmetry plane), are presented for angles of attack from -10 to 10 deg. The high normal-shock density ratio of a real gas was simulated by tests at a Mach number of 6 in air and CF4 (density ratio equal to 5.25 and 12.0, respectively). Tests were conducted in air at Mach 6 and 10 and in CF4 at Mach 6 to examine the effects of Mach number, Reynolds number, and normal-shock density ratio. Changes in Mach number from 6 to 10 in air or in Reynolds number by a factor of 4 at Mach 6 had a negligible effect on lateral and directional stability characteristics. Variations in normal-shock density ratio had a measurable effect on lateral and directional aerodynamic coefficients, but no significant effect on lateral and directional stability characteristics. Tests in air and CF4 indicated that the configuration was laterally and directionally stable through the test range of angle of attack.

Micol, John R.↗

NASA NTRS1990

Surface flow and heating distributions on a cylinder in near wake of Aeroassist Flight Experiment (AFE) configuration at incidence in Mach 10 Air

Experimental heat transfer distributions and surface streamline directions are presented for a cylinder in the near wake of the Aeroassist Flight Experiment forebody configuration. Tests were conducted in air at a nominal free stream Mach number of 10, with post shock Reynolds numbers based on model base height of 6,450 to 50,770, and angles of attack of 5, 0, -5, and -10 degrees. Heat transfer data were obtained with thin film resistance gage and surface streamline directions by the oil flow technique. Comparisons between measured values and predicted values were made by using a Navier-Stokes computer code.

Wells, William L.↗

NASA NTRS1989

Advantages of a round-body shuttle

A cylindrical fuselage cross-section SSTOV representing the design generation beyond the current NASA Space Shuttle has been projected capable of reducing the cost of payload delivery to orbit while increasing mission scope. Due to its intrinsically greater wetted-area and structural weight efficiencies, this cylindrical vehicle would carry 40 percent greater payload than the Space Shuttle system despite a 20-percent lower gross liftoff weight. A LOX/hydrocarbon fuel combination would be employed during the early portion of flight, thereupon shifting to LOX/hydrogen. The cylindrical SSTOV would have eight times the volume of the Space Shuttle Orbiter.

Arrington, James P.↗

NASA NTRS1989

Measured and predicted aerodynamic heating on a cylinder in wake of AFE configuration at incidence

Thin-film resistance gages were used to measure cylinder surface heat-transfer rates in the near wake of the Aeroassist Flight Experiment vehicle configuration, while surface-streamline directions were ascertained by the oil-flow techniques under the same configuration and test conditions. Both heat transfer distributions and flow over the entire cylinder surface were influenced by impingement of that portion of the free shear layer originating at the forebody shoulder in the upper symmetry plane. Heating rate distributions predicted with a Navier-Stokes solver computer code were in general agreement with measurements.

Wells, William L.↗

NASA NTRS1989

Measured and predicted aerodynamic coefficients and shock shapes for Aeroassist Flight Experiment (AFE) configuration

Two scaled models of the Aeroassist Flight Experiment (AFE) vehicle were tested in two air wind tunnels and one CF4 tunnel. The tests were to determine the static longitudinal aerodynamic characteristics, and shock shapes for the configuration in hypersonic continuum flow. The tests were conducted with a range of angle of attack to evaluate the effects of Mach number, Reynolds numbers, and normal shock density ratio.

Wells, William L.↗

NASA NTRS1988

Measured and predicted shock shapes for AFE configuration at Mach 6 in air and in CF4

Shock shapes and stand-off distances were obtained for the Aeroassist Flight Experiment configuration from Mach 6 tests in air and in CF4. Results were plotted for an angle-of attack range from -10 to 10 degrees and comparisons were made at selected angles with inviscid-flow predictions. Tests were performed in the Langley Research Center (LaRC) 20 inch Mach 6 Tunnel (air) at unit free-stream Reynolds numbers (N sub Re, infinity) of 2 million/ft and 0.6 million/ft and in the LaRC Hypersonic CF4 Tunnel at N sub Re, infinity = 0.5 million/ft and 0.3 million/ft. Within the range of these tests, N sub Re, infinity did not affect the shock shape or stand off distance, and the predictions were in good agreement with the measurements. The shock stand-off distance in CF4 was approximately half of that in air. This effect resulted from the differences in density ratio across the normal shock, which was approximately 12 in CF4 and 5 in air. In both test gases, the shock lay progressively closer to the body as angle of attack decreased.

Wells, William L.↗

NASA NTRS1987

Wind-tunnel preflight test program for aeroassist flight experiment

A proposed Aeroassist Flight Experiment (AFE) will simulate return from geosynchronous orbit to low-earth orbit to provide fundamental information about the hypersonic flow conditions surrounding aeroassisted orbital transfer vehicles (AOTV's). Future AOTV design must rely heavily on computational fluid dynamic (CFD) computer codes now under development, since the entry conditions are beyond the simulation capabilities of ground-based test facilities. However, existing codes and best available ground-based test facilities must provide for design of the AFE. The AFE ground-based test program provides data for calibration of existing and developing pertinent CFD codes. Confidence in code prediction capability increases with ability to predict forces and moments, pressure and heat-transfer distributions, shock shapes, and surface streamline directions. The ground-based test program provides these data over a wide range of hypersonic test parameters. This paper describes the test program, models, facilities, and some representative results.

Wells, William L.↗

NASA NTRS1985

Heating Rate Distributions at Mach 10 on a Circular Body Earth-to-Orbit Transport Vehicle

Among the concepts being considered for future Earth-to-orbit transport vehicles are fully reusable single-stage systems which take off vertically and land horizontally. Because these vehicles carry their own propellant internally, they are much larger than the present Space Shuttle Orbiter. One such single-stage vehicle under study is the circular body configuration which has the advantages of simple structural design and large volume-to-weight ratio. As part of an overall evaluation of this configuration, a series of heat transfer and surface flow tests were conducted. The phase-change paint and oil-flow tests were performed in the Langley 31-Inch Mach-10 Tunnel at angles of attack from 20 through 40 degrees in 5-degree increments. Heat-transfer coefficient data are presented for all angles of attack and detailed oil-flow photographs are shown for windward and leeward surfaces at 25 and 40 degrees angle of attack. In many ways, heating was similar to that previously determined for the Shuttle Orbiter so that, in a cursory sense, existing thermal protection systems would appear to be adequate for the proposed circular-body configurations.

Wells, William L.↗