Engineering topics
Wercinski, Paul
Publications and source records attributed to Wercinski, Paul.
Sustaining Mature Entry System Technologies Crucial for Future In-Situ Venus Missions
Severe entry environments at Venus are a key challenge for all missions employing probes, landers, areal platforms, aerocapture and atmospheric skimming. Three specific mature technologies, PICA, HEEET, and ADEPT, are enablers for Venus in-situ missions but are at risk of atrophy or loss if not maintained. All three technologies were NASA-developed in partnership with US industry and rely on both organizations for intellectual property. These technologies are needed only for NASA missions and lack applicability elsewhere. NASA has experienced the loss of prior TPS technologies due to lack of use, including Apollo’s Avcoat (re-created at enormous expense for Orion) and Pioneer-Venus’ heritage carbon phenolic. Given the low flight cadence for planetary entry missions overall and the lack of non-NASA uses for these technologies, there is a real concern for the sustainment of key entry technologies.
ADEPT Sounding Rocket One (SR-1) Flight Test
A sounding rocket flight test was conducted on a mechanically-deployed entry vehicle (DEV) known as the Adaptable Deployable Entry and Placement Technology (ADEPT). This flight test was a major milestone in a technology development campaign for ADEPT: the application of ADEPT for small secondary payloads. The test was conducted above White Sands Missile Range (WSMR), New Mexico on a SpaceLoft XL rocket on September 12, 2018. The first objective of the SR-1 flight test was to demonstrate that ADEPT could transform from a compact stowed configuration, separate from the launch vehicle, and successfully deploy exo-atmospherically into the desired low ballistic coefficient entry configuration. The second objective was to characterize the aerodynamic performance of the deployed configuration in order to evaluate the faceted blunt body geometry dynamic stability characteristics as it decelerated from supersonic to subsonic speeds.The ADEPT DEV had several sensors on-board and also leveraged third-party data sources for post-flight analysis and trajectory reconstruction. Based upon data review, the launch vehicle met exo-atmospheric delivery performance requirements of spin rate, no re-contact, separation velocity, and delivery altitude. The unique ADEPT forebody geometry (blunted octagonal pyramid, 0.7 m diameter at the rib tips) and aftbody configuration has never flown before. The forebody half cone angle at the ribs is 70 deg, while the half cone angle mid gore is 68.5 deg. The aftbody, where the 3U CubeSat 'payload' resides is a rectangular prism that extends ~ ½ the minimum forebody diameter behind the nose. Understanding DEV blunt body dynamic stability performance is critical for determining how they can be employed for atmospheric entry, descent and landing.The primary data products were used to perform flight mechanics analysis and reconstruct the as-flown trajectory. On-board video recovered post-flight demonstrated that the DEV achieved and maintained the desired entry configuration. Post-flight analyses showed that the vehicle met the threshold of achieving stable flight below Mach = 0.8. The ADEPT project has focused on ballistic, axisymmetric shapes as the logical 'first step' in mission infusion applications. With the current maturation and development of the ballistic (non-lifting) 1 m class ADEPT, the next step in ADEPT maturation is the focus on configurations that are capable of generating lift in order to accomplish aerocapture and precision landing mission capabilities. ADEPT is particularly attractive for evaluating various guidance and control approaches as the deployable structure enables attachment points for various actuation methods such as control surfaces, moving mass elements, or RCS thrusters. The ADEPT sounding rocket flight test provided a low-cost means of achieving significant system level maturity for the 1 m class ADEPT configuration. A description of the technology, system components, flight test execution, and conclusions will be described.
ADEPT Sounding Rocket One Flight Test Overview
On September 12th 2018, a sounding rocket flight test was conducted on a mechanically-deployed atmospheric entry system known as the Adaptable Deployable Entry and Placement Technology (ADEPT). The purpose of the Sounding Rocket One (SR-1) test was to gather critical flight data for evaluating the vehicle's in-space deployment performance and supersonic stability. This flight test was a major milestone in a technology development campaign for ADEPT: the application of ADEPT for small secondary payloads. The test was conducted above White Sands Missile Range (WSMR), New Mexico on a SpaceLoft XL rocket manufactured by UP Aerospace. This paper describes the system components, test execution, and test conclusions.
ADEPT for Interplanetary Small Satellite Missions
There is growing interest for utilizing Small Satellites beyond low Earth orbit. A number of secondary CubeSat payload missions are planned at Mars, cis-Lunar Space, near Earth objects, and moons of the Gas Giants. Use of smaller systems may enable utilization of otherwise unused capacity of larger "host" missions. Development of re-entry systems that leverage and accommodate Small Satellite technology will substantially expand the range of mission applications by offering the capability for high speed entry or aerocapture at destinations with atmospheres. Deployable entry vehicles (DEVs) offer benefits over traditional rigid aeroshells including volume, mass and payload form factor. The Adaptive Deployable Entry and Placement Technology (ADEPT) offers such a delivery capability for Small Sat or CubeSat orbiter(s), in-situ elements, or landers. The ADEPT system can package with off the shelf CubeSat deployment systems (1U-16U) to offer a delivery capability for a single CubeSat or constellations. Furthermore, ADEPT can deliver the same science payload to a destination with a stowed diameter a factor of 3-4 times smaller than an equivalent rigid aeroshell, alleviating volumetric constraints on the secondary payload accommodation or primary carrier spacecraft bus. This paper will describe ADEPT's current development status and define various interplanetary mission concepts in order to provide guidelines for potential Small Satellite payload developers and mission implementers.
SmallSat aerocapture to enable a new paradigm of planetay missions
This paper presents a technology development initiative focused on delivering SmallSats to orbit a variety of bodies using aerocapture. Aerocapture uses the drag of a single pass through the atmosphere to capture into orbit instead of relying on large quantities of rocket fuel. Using drag modulation flight control, an aerocapture vehicle adjusts its drag area during atmospheric flight through a single-stage jettison of a drag skirt, allowing it to target a particular science orbit in the presence of atmospheric uncertainties. A team from JPL, NASA Ames, and CU Boulder has worked to address the key challenges and determine the feasibility of an aerocapture system for SmallSats less than 180kg. Key challenges include the ability to accurately target an orbit, stability through atmospheric flight and the jettison event, and aerothermal stresses due to high heat rates.
Presentation to Technology, Innovation & Engineering Committee NASA Advisory Council
No abstract available
Studies in Support of Venus Aerocapture Utilizing Drag Modulation
Aerocapture has been extensively studied and these studies have shown the benefit for planetary exploration missions. While the traditional approach to aerocapture with lifting configurations and lift-guided modulations have been assessed to be technologically feasible, aerocapture using purely drag modulation was proposed and studied by Prof. Braun and his students. These studies show that if one can assess the feasibility of aerocapture using drag modulation at Venus, and develop tall pole technologies needed at Venus, then this concept is much easier to execute at all other relevant destinations. Based on the above finding, partnered proposals were submitted by Adam Nelessen at JPL and Ethiraj Venkatapathy at Ames in collaboration with Prof. Braun at the University of Colorado, Boulder (UCB). Under this partnership, Ames Research Center (ARC) is working to address some of the key entry technology challenges associated with drag modulation aerocapture at Venus. Drag modulation aerocapture is a simple, scalable, and likely cost-effective way to enhance planetary science missions. The approach envisioned is to design a small spacecraft, that would most likely be a secondary payload, with a removable drag skirt. The vehicle would enter the atmosphere at Venus with a low ballistic coefficient, decelerate rapidly, drop the skirt resulting in a smaller vehicle with a higher ballistic coefficient which would skip out of the atmosphere and enter into a desired orbit. ARC's role in this collaboration is multifold. First of which is to perform design studies on various pre- and post-jettison geometries utilizing a 3-DOF trajectory code to determine the aerodynamics and aerothermodynamics of the vehicles and evaluate viable thermal protection material system designs. Once these design studies are complete, Ames will then perform higher fidelity CFD and TPS sizing to further design the vehicles. Second, the multi-body separation dynamics of the drag modulation event will be explored using both CFD simulations (CART3-D and US3D) as well as possible ballistic range testing. ARC's tools and expertise have been used to assess and advise on the selection of the separating configuration. In addition to the preliminary evaluation, ARC will provide tools and expertise to UCB team members to further assess aerodynamic interactions between the separating bodies and provide guidance as to the feasibility of stable transition.
ADEPT SR-1 Development and Testing
The Adaptable Deployable Entry and Placement Technology (ADEPT) Sounding Rocket One (SR-1) fight test will be the first sub-orbital flight of Nano-ADEPT. Nano-ADEPT is a deployable heatshield for secondary payload missions desiring to re-enter the Earth's atmosphere or deliver small science payloads to Mars or Venus. Two units have been built and tested in preparation of launch: one designated the "Spare" unit and one the "Flight" unit. The general development approach has been to perform all procedures on the Spare prior to performing them on Flight. This approach has served the project well, allowing for procedures to be rapidly developed and tested on spare hardware where mistakes are less consequential. Conversely, when schedule constraints have come up, the approach has allowed the project to rapidly pivot to an approach where Flight drives the critical path rather than Spare. This approach has enabled relatively rapid development of Flight where technical risk is balanced with schedule realism. This presentation will describe the various tests that have been performed on Nano-ADEPT Spare and Flight units to prepare for the sub-orbital flight. The purpose is to communicate the development approach we took for this low-cost, moderate-risk flight test and hopefully engage the EDL community in a wider discussion of risk-balanced approaches toward flight hardware development of secondary payload atmospheric entry systems.
TPS for Outer Planets
This invited talk will provide an assessment of the TPS needs for Outer Planet In-situ missions to destinations with atmosphere. The talk will outline the drivers for TPS from destination, science, mission architecture and entry environment. An assessment of the readiness of the TPS, both currently available and under development, for Saturn, Titan, Uranus and Neptune are provided. The challenges related to sustainability of the TPS for future missions are discussed.
Venus Entry Challenges and Solutions for Aerial Platform Deployment
Venus presents unique challenges for entry and deployment of aerial platforms. This invited presentation addresses the challenges and the solution including rigid and deployable systems.
The Adaptable, Deployable Entry and Placement Technology (ADEPT)
The initial system-level development of the nano-ADEPT architecture will culminate in the launch of a 0.7 meter deployed diameter ADEPT sounding rocket flight experiment named, SR-1. Launch is planned for August 2017. The test will utilize the NASA Flight Opportunities Program sounding rocket platform provided by UP Aerospace to launch SR-1 to an apogee over 100 km and achieve re-entry conditions with a peak velocity near Mach 3. The SR-1 flight experiment will demonstrate most of the primary end-to-end mission stages including: launch in a stowed configuration, separation and deployment in exo-atmospheric conditions, and passive ballistic re-entry of a 70-degree half-angle faceted cone geometry.
Looking Up: An SMD Technology Brown Bag Series - The Adaptable, Deployable Entry and Placement Technology (ADEPT)
No abstract available
ADEPT Sounding Rocket One (SR-1)Flight Experiment Overview
The SR-1 flight experiment will demonstrate most of the primary end-to-end mission stages including: launch in a stowed configuration, separation and deployment in exo-atmospheric conditions, and passive ballistic re-entry of a 70-degree half-angle faceted cone geometry.
System Level Aerothermal Testing for the Adaptive Deployable Entry and Placement Technology (ADEPT)
The Adaptive Deployable Entry and Placement Technology (ADEPT), a mechanically deployable entry vehicle technology, has been under development at NASA since 2011. As part of the technical maturation of ADEPT, designs capable of delivering small payloads (10 kg) are being considered to rapidly mature sub 1 m deployed diameter designs. The unique capability of ADEPT for small payloads comes from its ability to stow within a slender volume and deploy to achieve a mass efficient drag surface with a high heat rate capability. The low ballistic coefficient results in entry heating and mechanical loads that can be met by a revolutionary three-dimensionally woven carbon fabric supported by a deployable skeleton structure. This carbon fabric has test proven capability as both primary structure and payload thermal protection system. In order to rapidly advance ADEPTs technical maturation, the project is developing test methods that enable thermostructural design requirement verification of ADEPT designs at the system level using ground test facilities. Results from these tests are also relevant to larger class missions and help us define areas of focused component level testing in order to mature material and thermal response design codes. The ability to ground test sub 1 m diameter ADEPT configurations at or near full-scale provides significant value to the rapid maturation of this class of deployable entry vehicles. This paper will summarize arc jet test results, highlight design challenges, provide a summary of lessons learned and discuss future test approaches based upon this methodology.