Search NASA⌕ Search

Engineering topics

Wesley, J C

Publications and source records attributed to Wesley, J C.

Control of post-disruption runaway electron beams in DIII-D

Recent experiments in the DIII-D tokamak have demonstrated real-time control and dissipation of post-disruption runaway electron (RE) beams. In the event that disruption avoidance, control, and mitigation schemes fail to avoid or suppress RE generation, active control of the RE beam may be an important line of defense to prevent the rapid, localized deposition of RE beam energy onto vulnerable vessel sections. During and immediately after the current quench, excessive radial compression of the runaway beams is avoided by a combination of techniques, improving the likelihood of the beams surviving this dynamic period without a fast termination. Once stabilized, the runaway beams are held in a steady state (out to the ohmic flux limit) with the application of active plasma current and position controls. Beam interaction with the vessel wall is minimized by avoiding distinct thresholds for enhanced wall interaction at small and large radii, corresponding to inner wall and outer limiter interaction, respectively. Staying within the 'safe zone' between those radial thresholds allows for the sustainment of long-lived, quiescent runaway beams. The total beam energy and runaway electron population are then dissipated gradually by a controlled ramp-down of the runaway current.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of Applied Toroidal Electric Field on the Growth/Decay of Plateau-Phase Runaway Electron Currents in DIII-D

Large relativistic runaway electron currents (0.1-0.5 MA) persisting for similar to 100 ms are created in the DIII-D tokamak during rapid discharge shut down caused by argon pellet injection. Slow upward and downward ramps in runaway currents were found in response to externally applied loop voltages. Comparison between the observed current growth/decay rate and the rate expected from the knock-on avalanche mechanism suggests that classical collisional dissipation of runaways alone cannot account for the measured growth/damping rates. It appears that a fairly constant anomalous dissipation rate of order 10 s(-1) exists, possibly stemming from radial transport or direct orbit losses to the vessel walls, although the possibility of an apparent loss due to current profile shrinking cannot be ruled out at present.

Hollmann, E M↗

Pellet interaction with runaway electrons

We describe results from recent experiments studying interaction of solid polystyrene pellets with a runaway electron current channel generated after cryogenic argon pellet rapid shutdown of DIII-D. Fast camera imaging shows the pellet trajectory and continuum emission from the subsequent explosion, with geometric calibration providing detailed explosion analysis and runaway energy. Electron cyclotron emission also occurs, associated with knock-on electrons broken free from the pellet by RE which then accelerate and runaway, and also with a short lived hot plasma blown off the pellet surface. In addition, we compare heating and explosion times from observations and a model of pellet heating and breakdown by runaway interaction. (C) 2011 Elsevier B.V. All rights reserved

43 PARTICLE ACCELERATORS↗

Plasma-surface interactions during tokamak disruptions and rapid shutdowns

Recent progress in understanding of disruptions and in developing methods to avoid disruption damage is presented. Nearly complete mitigation of conducted heat loads has been achieved with high-Z gas jet shutdown. The resulting local radiation heat flash melting in the main chamber might be a concern in ITER, especially with beryllium walls. During the current quench, significant vessel forces can occur due to halo currents I-halo; however, these are found to fall reliably below a boundary of (halo current fraction times halo current peaking factor) <0.7 both experimentally and numerically. Numerical simulations indicate that runaway electrons (REs) could cause serious damage to hard-to reach components in ITER, making their suppression a high priority. During the current quench, less than 20% of the density required for collisional suppression of REs appears to have been achieved. Collisional suppression of REs may have been achieved, however, in full-current RE beams with gas injection. (C) 2010 Elsevier B.V. All rights reserved.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Demonstration of rapid shutdown using large shattered deuterium pellet injection in DIII-D

A severe consequence of a disruption on large tokamaks such as ITER could be the generation of multi-megaelectronvolt electron beams that could damage the vacuum vessel and the structures of the machine if they hit the wall unmitigated. The mitigation of runaway electron beams is thus a key requirement for reliable operation of ITER. In order to achieve reliable disruption mitigation, a new fast shutdown technique has been developed: the injection of a large shattered cryogenic pellet in the plasma, which is expected to increase the electron density up to levels where the beam generation processes are mitigated by collisional losses. This technique has been implemented and tested for the first time ever on DIII-D. The first tests show evidence of an almost instantaneous deposition of more than 260 Pa m(3) of deuterium deep in the core. Record local densities during the thermal quench were observed for each injection with a very high reliability. Pellet mass and plasma energy content scans show an improvement of the assimilation of the particles for higher plasma energy and larger pellet mass.

Commaux, Nicolas JC↗

Experiments in DIII-D toward achieving rapid shutdown with runaway electron suppression

Experiments have been performed in the DIII-D tokamak [J. L. Luxon, Nucl. Fusion 42, 614 (2002)] toward understanding runaway electron formation and amplification during rapid discharge shutdown, as well as toward achieving complete collisional suppression of these runaway electrons via massive delivery of impurities. Runaway acceleration and amplification appear to be well explained using the zero-dimensional (0D) current quench toroidal electric field. 0D or even one-dimensional modeling using a Dreicer seed term, however, appears to be too small to explain the initial runaway seed formation. Up to 15% of the line-average electron density required for complete runaway suppression has been achieved in the middle of the current quench using optimized massive gas injection with multiple small gas valves firing simultaneously. The novel rapid shutdown techniques of massive shattered pellet injection and shell pellet injection have been demonstrated for the first time. Experiments using external magnetic perturbations to deconfine runaways have shown promising preliminary results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗