Search NASA⌕ Search

Engineering topics

Westfall, L. J.

Publications and source records attributed to Westfall, L. J..

13 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Compressive strength of a B2 matrix NiAl-Nb intermetallic at 1200 and 1300 K

The effect of a large Nb addition to a NiAl, to a final composition 43.5Ni-45.2Al-0.8Fe-10.5Nb (in at. pct), on the high-temperature compressive strength of NiAl was investigated using cylindrical samples which were compression tested in air at 1200 K and 1300 K under constant-velocity conditions. The compressive strength of the Ni-45Al-10.5Nb was compared to data from all known solid solution-strengthened and/or precipitation-strengthened NiAl-based materials. It was found that, for strain rates higher than 5 x 10 to the -6th/sec, the Ni-45Al-10.5Nb is stronger than NiAl. However, this advantage disappears at lower strain rates. A comparison of NiAl-based materials indicated that a NiAl+TiB2 composite containing 20 vol pct 1-micron-diam particles has a strength superiority over all the solid solution and precipitation-hardened aluminides at strain rates below 10 to the -7th/sec.

Whittenberger, J. Daniel↗
NASA NTRS1986

Fiber-reinforced superalloy composites provide an added performance edge

Fiber reinforcements are being explored as a means to increasing the performance of superalloys past 980 C. Fiber-reinforced superalloys (FRS), particularly tungsten FRS (TFRS) are candidate materials for rocket-engine turbopump blades for advanced Shuttle engines and in airbreathing and other rocket engines. Refractory metal wires are the reinforcement of choice due to tolerance to fiber/matrix interactions. W alloy fibers have a maximum tensile strength of 2165 MPa at 1095 C and a 100 hr creep rupture strength at stresses up to 1400 MPa. A TFRS has the potential of a service temperature 110 C over the strongest superalloy. Manufacturing processes being evaluated to realize the FRS components are summarized, together with design features which will be introduced in turbine blades to take advantage of the FRS materials and to extend their surface life.

Petrasek, D. W.↗
NASA NTRS1985

Arc spray fabrication of metal matrix composite monotape

Arc metal spraying is used to spray liquid metal onto an array of high strength fibers that were previously wound onto a large drum contained inside a controlled atmosphere chamber. This chamber is first evacuated to remove gaseous contaminants and then backfilled with a neutral gas up to atmospheric pressure. This process is used to produce a large size metal matrix composite monotape.

Westfall, L. J.↗
NASA NTRS1985

Thermal-mechanical fatigue test apparatus for metal matrix composites and joint attachments

Two thermal-mechanical fatigue (TMF) test facilities were designed and developed, one to test tungsten fiber reinforced metal matrix composite specimens at temperature up to 1430C (2600F) and another to test composite/metal attachment bond joints at temperatures up to 760C (1400 F). The TMF facility designed for testing tungsten fiber reinforced metal matrix composites permits test specimen temperature excursions from room temperature to 1430C (2600F) with controlled heating and loading rates. A strain-measuring device measures the strain in the test section of the specimen during each heating and cooling cycle with superimposed loads. Data is collected and recorded by a computer. The second facility is designed to test composite/metal attachment bond joints and to permit heating to a maximum temperature of 760C (1400F) within 10 min and cooling to 150C (300F) within 3 min. A computer controls specimen temperature and load cycling.

Westfall, L. J.↗
NASA NTRS1979

Thermal-conductivity measurements of tungsten-fiber-reinforced superalloy composites using a thermal-conductivity comparator

The thermal conductivity (TC) of tungsten-fiber-reinforced superalloys was determined for two composite systems by using a thermal conductivity standard from the National Bureau of Standards and a comparator and technique developed for that purpose. The results were compared with TC data for the nickel-base alloy MAR-M200. The technique lends itself to applications involving thin specimens, such as thin-walled turbine blades. The TC's of the composite systems were considerably higher in both the longitudinal and transverse directions than that of the monolithic superalloys used as the matrices.

Westfall, L. J.↗
NASA NTRS1979

Tungsten fiber reinforced FeCrAlY - A first generation composite turbine blade material

General and composite turbine blade material requirements are examined to identify a specific tungsten fiber reinforced superalloy (TFRS) having, in addition to strength, the desired combination of other material properties needed in turbine blades. Experimental data indicated that a thoriated tungsten fiber reinforced FeCrAlY matrix composite should have the stress-rupture, creep, tensile, fatigue, and impact strengths required for turbine blades operating from 1250 to 1370 K. Fabrication and design concepts are developed to demonstrate the feasibility of fabricating a hollow TFRS turbine blade at reasonable cost.

Petrasek, D. W.↗
NASA NTRS1979

Tungsten fiber reinforced FeCralY: A first generation composite turbine blade material

Tungsten-fiber/FeCrAlY (W/FeCrAlY) was identified as a promising aircraft engine, first generation, turbine blade composite material. Based on available data, W/FeCrAlY should have the stress-rupture, creep, tensile, fatigue, and impact strengths required for turbine blades operating from 1250 to 1370 K. It should also have adequate oxidation, hot corrosion, and thermal cycling damage resistance as well as high thermal conductivity. Concepts for potentially low cost blade fabrication were developed. These concepts were used to design a first stage JT9D convection cooled turbine blade having a calculated 50 K use-temperature advantage over the directionally solidified superalloy blade.

Petrasek, D. W.↗
NASA NTRS1978

Predicted inlet gas temperatures for tungsten fiber reinforced superalloy turbine blades

Tungsten fiber-reinforced superalloy composite (TFRS) impingement-cooled turbine blade inlet gas temperatures were calculated taking into account material spanwise strength, thermal conductivity, material oxidation resistance, fiber-matrix interaction, and coolant flow. Measured values of TFRS thermal conductivities are presented. Calculations indicate that blades made of 30 volume percent fiber content TFRS having a 12,000 N-m/kg stress-to-density ratio while operating at 40 atm and a 0.06 coolant flow ratio could permit a turbine blade inlet gas temperature of over 1900 K. This is more than 150 K greater than similar superalloy blades.

Winsa, E. A.↗
NASA NTRS1978

Predicted inlet gas temperatures for tungsten fiber reinforced superalloy turbine blades

Tungsten fiber reinforced superalloy composite (TFRS) impingement cooled turbine blade inlet gas temperatures were calculated taking into account material spanwise strength, thermal conductivity, material oxidation resistance, fiber-matrix interaction, and coolant flow. Measured values of TFRS thermal conductivities are presented. Calculations indicate that blades made of 30 volume percent fiber content TFRS having a 12,000 N-m/kg stress-to-density ratio while operating at 40 atmospheres and a 0.06 coolant flow ratio could permit a turbine blade inlet gas temperature of over 1900K. This is more than 150K greater than similar superalloy blades.

Winsa, E. A.↗
NASA NTRS1978

Predicted inlet gas temperatures for tungsten fiber reinforced superalloy turbine blades

A procedure is presented for predicting the magnitude of the turbine inlet gas temperatures potentially achievable using first generation tungsten fiber reinforced superalloys (TFRS) turbine blades. Both uncoated blades and blades with thermal barrier coatings are considered. The thermal conductivities of two representative TFRS were measured over a range of temperatures. The results show that cooled TFRS blades may allow significantly higher gas temperatures than are possible with superalloy blades. For one design, the difference is about 150-200 K.

Winsa, E. A.↗
NASA NTRS1972

Effective separation technique for small diameter whiskers.

Description of a technique for separating small-diameter whiskers from the as-grown matt by gently agitating the whisker matts in a solution of deionized or distilled water for six to eight hours. High-strength Al2O3 whiskers were effectively separated by this technique, comprising an average 48% of the original weight of the whisker matt. According to estimation, more than 90% of separated whiskers had diameters between 0.7 and 2.0 microns.

Westfall, L. J.↗