Search NASA⌕ Search

Engineering topics

Westover, Andrew S.

Publications and source records attributed to Westover, Andrew S..

At least 19 records

Electroanalytical Exploration of Li Loss at the Solid Electrolyte-Anode Interface in Anode-Free Batteries with Polymer Electrolytes

Li loss during cycling at the solid electrolyte|anode interface strongly determines the cycle life of anode-free solid-state batteries (SSBs). Here, this loss is probed electroanalytically for polymer electrolyte (PE)-based SSBs in anode-free coin cells with practical pressures. A wide range of parameters expected to impact the measured average coulombic efficiency (CE) were explored to estimate the expected range of performance. These factors include PE type, cycling profiles, current collector type, and the presence of a thin Li seed layer. Further, low CE values in the ~50%–85% range are observed for all electrolytes and test conditions. Other than the electrolyte type, a strong dependence of the CE on the electrochemical cycling profile and the type of metallic current collector is observed. Compared to the anode-free setup, the presence of a thin (5 μ m) Li seed layer did not improve the average CE for two out of three PEs, suggesting its presence to be a weak contributor in minimizing the Li loss. This work provides baseline data on the Li losses in low-pressure anode-free configuration cells with PEs.

25 ENERGY STORAGE↗

Understanding the complexities of Li metal for solid-state Li-metal batteries

Li-metal anodes are a key enabling technology for next-generation high-energy batteries, including Li–S, Li-air, and high-voltage cathodes. While most research enabling Li metal focuses on electrolyte design, especially in the solid state, the nature of the Li metal itself has a significant impact on the performance of both solid- and liquid-based batteries. This has historically been understudied, but recent work has highlighted the importance of tailoring the Li metal to optimize high-performance batteries. This article focuses on the key aspects of Li metal that impact performance, including the method of synthesis, microstructure, surfaces, impurities, mechanics, and alloying strategies to optimize Li anode performance. Finally, the article will also briefly look at the impact of long-term cycling on the evolution of Li-metal anodes in solid-state batteries and highlight key areas of needed research.

25 ENERGY STORAGE↗

Ionically conductive powders and films, and methods of preparation

A solid ionically conductive composition (e.g., nanoparticles of less than 1 micron or a continuous film) comprising at least one element selected from alkali metal, alkaline earth metal, aluminum, zinc, copper, and silver in combination with at least two elements selected from oxygen, sulfur, silicon, phosphorus, nitrogen, boron, gallium, indium, tin, germanium, arsenic, antimony, bismuth, transition metals, and lanthanides. Also described is a battery comprising an anode, a cathode, and a solid electrolyte (corresponding to the above ionically conductive composition) in contact with or as part of the anode and/or cathode. Further described is a thermal (e.g., plasma-based) method of producing the ionically conductive composition. Further described is a method for using an additive manufacturing (AM) process to produce an object constructed of the ionically conductive composition by use of particles of the ionically conductive composition as a feed material in the AM process.

Kercher, Andrew K.↗

Solid-state batteries: The critical role of mechanics

Solid-state batteries with lithium metal anodes have the potential for higher energy density, longer lifetime, wider operating temperature, and increased safety. Although the bulk of the research has focused on improving transport kinetics and electrochemical stability of the materials and interfaces, there are also critical challenges that require investigation of the mechanics of materials. In batteries with solid-solid interfaces, mechanical contacts, and the development of stresses during operation of the solid-state batteries, become as critical as the electrochemical stability to keep steady charge transfer at these interfaces. In conclusion, this review will focus on stress and strain that result from normal and extended battery cycling and the associated mechanisms for stress relief, some of which lead to failure of these batteries.

25 ENERGY STORAGE↗

Structure-mechanical properties correlation in bulk LiPON glass produced by nitridation of metaphosphate melts

The glassy solid electrolyte Lithium phosphorous oxynitride (LiPON) has been widely researched in thin film solid state battery format due to its outstanding stability when cycled against lithium. In addition, recent reports show thin film LiPON having interesting mechanical behaviors, especially its ability to resist micro-scale cracking via densification and shear flow. Here, in the present study, we have produced bulk LiPON glasses with varying nitrogen contents by ammonolysis of LiPO 3 melts. The resulting compositions were determined to be LiPO 3-3z/2 N z , where 0 ≤ z ≤ 0.75, and the z value of 0.75 is among the highest ever reported for this series of LiPON glasses. The short-range order structures of the different resulting compositions were characterized by infrared, Raman, 31 P magic angle spinning nuclear magnetic resonance, and X-ray photoelectron spectroscopies. Instrumented nano-indentation was used to measure mechanical properties. It was observed that similar to previous studies, both trigonally coordinated (N t ) and doubly bonded (N d ) N co-exist in the glasses in about the same amounts for z ≤ 0.36, the limit of N content in most previous studies. For glasses with z > 0.36, it was found that the fraction of the N t increased significantly while the fraction of N d correspondingly decreased. The incorporation of nitrogen increased both the elastic modulus and hardness of the glass by approximately a factor of 1.5 when N/P ratio reaches 0.75. At the same time, an apparent embrittlement of the glass was observed due to nitridation, which was revealed by nanoindentation with an extra sharp nanoindenter tip.

25 ENERGY STORAGE↗

In Situ Measurement of Buried Electrolyte–Electrode Interfaces for Solid State Batteries with Nanometer Level Precision

Many technologies including high-energy solid-state batteries rely on high quality solid–solid interfaces. Solid–solid interfaces are particularly difficult to study as their nature requires the interface to be buried. Here, in this work, we demonstrate the use of a combination of neutron reflectometry and in situ electrochemistry to measure the interface between Li metal and the solid electrolyte LiPON across an 8 cm 2 area. Neutron reflectometry measurements confirm the interphase to be less than 7 nm thick. The neutron reflectometry data further emphasize that the interphase that forms is a chemical gradient consisting of a Li-rich layer that gradually decreases in Li content until it blends into pure LiPON. Experimental confirmation that we can make ideal solid–solid interphases less than 10 nm thick will help facilitate the adoption of high efficiency next generation solid state batteries. Further this combination of complementary techniques provides a more general methodology for studying buried solid–solid interfaces across applications.

25 ENERGY STORAGE↗

Medium-Range Ordering in the Ionic Glass Electrolytes LiPON and LiSiPON

In this work, we provide an in-depth structural characterization of the amorphous ionic glasses LiPON and LiSiPON with high Li content. Based on ab initio molecular dynamics simulations, the structure of these materials is an inverted structure with either isolated polyanion tetrahedra or polyanion dimers in a Li+ matrix. Based on neutron scattering data, this type of inverted structure leads to a significant amount of medium-range ordering in the structure, as demonstrated by two sharp diffraction peaks and a periodic structural oscillation in the density function G(r). While this medium-range ordering is commonly observed in liquids and metallic glasses, it has not previously been observed in oxides. On a local scale, adding N and Si increases the number of anion bridges and polyanion dimer structures, leading to higher ionic conductivity. In the medium-range ordering, the addition of Si leads to more disorder in the polyanion substructure but a significant increase in the ordering of the O substructure. Finally, we demonstrate that this inverted structure with medium-range ordering results in a glassy material that is both mechanically stiff and ductile on the nanoscale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Li Morphology Evolution during Initial Cycles in a Gel Composite Polymer Electrolyte

Understanding and controlling lithium morphology evolution and lithium dendrite formation and growth during cycling is one of the key challenges for high-energy lithium metal batteries. This challenge applies to liquid electrolyte batteries as well as solid-state and semi-solid-state batteries. Our current knowledge about the evolution of the Li morphology is mostly obtained from liquid electrolyte-based studies in a Li–Li symmetrical cell configuration. The knowledge obtained in such conditions may not readily transfer into solid-state or semi-solid-state batteries. In this work, Li morphology evolution during initial cycling in a full cell configuration with the LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NMC 622) cathode and a semi-solid-state gel composite electrolyte is monitored via post-mortem photographs and scanning electron microscopy at multiple length scales. The gel composite electrolyte contains a cross-linked poly(ethylene oxide)-based polymer electrolyte, ceramic fillers, and a liquid plasticizer. The results show that severe surface pitting occurs as early as the second stripping cycle. Pit formation and continuous dissolution during the stripping process are the main cause of the Li surface roughening and dendrite growth mechanism in the model gel composite electrolyte. Comparing Li dendrite growth mechanisms in liquid, polymer, and ceramic solid electrolytes, the dendrite growth mechanism observed in this model electrolyte resembles that of the liquid electrolyte the most. This study suggests that strategies to control Li morphology and prevent dendrite growth in a gel composite electrolyte should be similar to strategies applicable to liquid electrolytes.

25 ENERGY STORAGE↗

Comparing the Purity of Rolled versus Evaporated Lithium Metal Films Using X-ray Microtomography

Here, we present a comparison of lithium metal films produced via rolling and thermal evaporation using synchrotron hard X-ray microtomography. In past studies of rolled lithium metal foils, a large number of C, O, and N impurities were found and identified as the key cause for failure in lithium metal cells. In this comparison, the X-ray tomography data show that the evaporated lithium metal films have an average impurity concentration of 19 particles/mm3 in comparison to 1350 particles/mm3 in the rolled lithium metal. An analysis of the inner substrate/lithium interface and outer lithium surface of the thermally evaporated film shows a much greater concentration of impurities at these interfaces, further emphasizing the importance of interface engineering in producing high-quality lithium metal batteries. Furthermore, we show that, if surface contamination can be avoided, it is possible to obtain lithium films with no impurities detectable by synchrotron hard X-ray tomography.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Challenges for and Pathways toward Li-Metal-Based All-Solid-State Batteries

Solid-state batteries utilizing Li metal anodes have the potential to enable improved performance (specific energy >500 Wh/kg, energy density >1500 Wh/L), safety, recyclability, and potentially lower cost (<$100/kWh) compared to advanced Li-ion systems.1,2 These improvements are critical for the widespread adoption of electric vehicles (EVs) and trucks and could create a short-haul electric aviation industry.1-3 Expectations for solid-state batteries are high, but there are significant materials and processing challenges to overcome.

25 ENERGY STORAGE↗

Challenges for and Pathways Toward Solid-State Batteries

Solid-state batteries utilizing lithium metal anodes have the potential to enable batteries with a specific energy of >500 Wh/kg and an energy density of >1,500 Wh/L for thousands of cycles. When optimized they will improve the energy efficiency, operating temperature range, sustainability, and safety at a lower cost compared to projections for advanced Li-ion batteries. This improved performance is critical for the widespread adoption of electric vehicles and may enable future applications such as electric aviation. Expectations for solid-state batteries are high, there are significant materials and processing challenges that need to be overcome. Some of these challenges are well known; others are more subtle and are just becoming known. The challenges and their solutions must be clearly identified to realize high-energy solid-state Li metal batteries. In the United States, the U.S. Department of Energy (DOE) funds the majority of energy storage research and development, including solid state battery research. Web of Science publication analysis shows that worldwide DOE is second largest funder. Work on solid state batteries is distributed across different arms of DOE and is coordinated at headquarters to ensure a broad national portfolio for advanced batteries, including lithium batteries and solid-state battery devices. We note that university and national laboratory researchers in the US with a long-standing interest in solid state batteries is a small, integrated community with recognized impact for publications, patents and startup companies. The opportunity for this group to engage for research with international colleagues is growing, fostered by periodic bilateral meetings supported by DOE and by the recent joint US German research program for lithium battery interface studies. These are valuable opportunities to speed solid-state battery development. The ORNL led virtual workshop, overviewed here, confirms the community’s shared vision of the exciting advances, opportunities, and challenges. Further, we are seeing that this workshop has spawned several new informal collaborations and draft proposals. This encourages us to propose future discussion. On May 11, 2020, Oak Ridge National Laboratory (ORNL) hosted a 6-hour, on-line national workshop to discuss recent advances and most the prominent obstacles to realizing solid-state Li metal batteries. The workshop included more than 30+ experts from national laboratories, universities, and companies, all of whom have worked on solid-state batteries for multiple years. The participants shared recent advances, many not yet in print, illustrating that the community has gained significant new insights for solid-state Li battery materials over the last 5 years. In this report, the major outcomes of the workshop are organized to identify the gaps in our scientific knowledge for four core materials science areas: (1) Li metal anodes, (2) the solid electrolyte in contact with Li metal, (3) active cathode materials and solid-state composite cathodes, and (4) solid electrolytes. Illustrative examples and discussions are reported with the more comprehensive issues in the report. Discussion of additional challenges related to processing of solid-state battery materials and to the designs and architectures for mechanically robust, long-lived batteries received less attention due to time constraints. These are good themes for deeper discussion at a follow-on workshop, where a complete list of critical research topics can be identified.

25 ENERGY STORAGE↗

Electroanalytical Measurement of Interphase Formation at a Li Metal–Solid Electrolyte Interface

The interphase between Li metal and solid electrolytes dictates performance in Li metal batteries. For the solid electrolyte Lipon, in this study we electroanalytically measure a capacity loss of 1.03 ± 0.16 μAh/cm 2 when Lipon first contacts Li metal. Assuming this capacity is all lost to interphase formation, this corresponds to a maximum Li consumption of 5.0 ± 0.8 nm to form an interphase ~4.7 nm thick. From dynamic electrochemical impedance spectroscopy (dEIS) during Li plating, we determine that nonlinear chaotic spectra demark this interphase formation and that this occurs immediately upon initiation of Li plating. dEIS also reveals interfacial resistance during both plating and stripping that decreases as the amount of plated Li increases.

25 ENERGY STORAGE↗

Challenges in Lithium Metal Anodes for Solid-State Batteries

In this Perspective, we highlight recent progress and challenges related to the integration of lithium metal anodes in solid-state batteries. While prior reports have suggested that solid electrolytes may be impermeable to lithium metal, this hypothesis has been disproven under a variety of electrolyte compositions and cycling conditions. Herein, we describe the mechanistic origins and importance of lithium filament growth and interphase formation in inorganic and organic solid electrolytes. Multimodal techniques that combine real and reciprocal space imaging and modeling will be necessary to fully understand nonequilibrium dynamics at these buried interfaces. Currently, most studies on lithium electrode kinetics at solid electrolyte interfaces are completed in symmetric Li–Li configurations. To fully understand the challenges and opportunities afforded by Li-metal anodes, full-cell experiments are necessary. Lastly, the impacts of operating conditions on solid-state batteries are largely unknown with respect to pressure, geometry, and break-in protocols. Given the rapid growth of this community and the diverse portfolio of solid electrolytes, we highlight the need for detailed reporting of experimental conditions and standardization of protocols across the community.

25 ENERGY STORAGE↗

Plasma Synthesis of Spherical Crystalline and Amorphous Electrolyte Nanopowders for Solid-State Batteries

Here, we demonstrate the theory-guided plasma synthesis of high purity nanocrystalline Li 3.5 Si 0.5 P 0.5 O 4 and fully amorphous Li 2.7 Si 0.7 P 0.3 O 3.17 N 0.22 . The synthesis involves the injection of single or mixed phase precursors directly into a plasma torch. As the material exits the plasma torch, it is quenched into spherical nanocrystalline or amorphous nanopowders. This process has virtually zero Li loss and allows for the inclusion of N, which is not accessible with traditional synthesis methods. Finally, we further demonstrate the ability to sinter the crystalline nanopowder into a dense electrolyte membrane at 800 °C, well below the traditional 1000 °C required for a conventional Li 3.5 Si 0.5 P 0.5 O 4 powder.

25 ENERGY STORAGE↗

Structural Degradation of High Voltage Lithium Nickel Manganese Cobalt Oxide (NMC) Cathodes in Solid-State Batteries and Implications for Next Generation Energy Storage

In this study, we report the stability of the layered high voltage cathode NMC622 with respect to a standard liquid electrolyte and in an all solid-state configuration. NMC622 cathodes with a (104) orientation were found to suffer from degradation at high voltage (4.5 V vs Li/Li + ) due to electrolyte-promoted degradation of the layered structure in a carbonate electrolyte. The lithium phosphorus oxynitride (LiPON) electrolyte was able to suppress the extent of this decomposition in solid-state cells but not totally prevent it from occurring. In the solid-state cells the capacity decreased from 203 to 93 mAh/g in the first cycle and from 93 to 79 mAh/g over the subsequent 99 cycles, whereas, after 20 cycles, the liquid cell charge capacity was dominated by the irreversible electrolyte degradation. Furthermore, the interfacial resistances of the solid-state cells were stable with cycling, suggesting minimal degradation of the NMC622/LiPON interface and incumbent losses due to structural evolution associated with cathode orientation. This data indicates that accessing stable high voltage capacity in NMCs will not be enabled by simply stabilizing the cathode–electrolyte interface. Optimizing cathode crystallographic orientation may be the key to accessing this high voltage regime.

25 ENERGY STORAGE↗

A three-dimensional interconnected polymer/ceramic composite as a thin film solid electrolyte

In this work we introduce an approach to fabricate a solid composite electrolyte film that is thin, ionically conductive, and mechanically robust with good potential for manufacturability, in the application of lithium metal batteries. First a doped-lithium aluminum titanium phosphate ceramic thin film with thickness of ~25 μm is formed by aqueous spray coating, a scalable process. The film is partially sintered to form a three-dimensionally interconnected structure with a dense backbone. It is then backfilled with a crosslinkable poly(ethylene oxide) (PEO)-based polymer electrolyte. We report the composite has very high ceramic loading of 77 wt% (61 vol%) and an ionic conductivity of 3.5 × 10 -5 S/cm at 20 °C with an activation energy of 0.43 eV. The main ion transport pathway is through the ceramic network, predicted by modelling and verified by experiments. Owing to the interconnected structure of the ceramic, the composite electrolyte exhibits much improved mechanical strength.

25 ENERGY STORAGE↗

Synthesis of Ni-Rich Thin-Film Cathode as Model System for Lithium Ion Batteries

We demonstrate a process to prepare model electrodes of the Ni-rich layered compound LiNi 0.6 Mn 0.2 Co 0.2 O 2 . These thin-film cathodes are compared with the composite materials to demonstrate the system is a viable platform for isolating interfacial phenomena between the electrolyte and active material without the influence of binders and conductive additives. The appropriate choice of heterolayers was found to influence the preferential orientation of the (101) and (104) planes relative to the (003) plane of the layered R-3m crystal structure, enhancing Li + diffusion and improving electrochemical performance. The addition of a Co interlayer between the Pt current collecting layer and alumina substrate increased the (101) and (104) texturing of the 500 nm Ni-rich film and allowed cells to deliver greater than 50% of their theoretical capacity. This work provides an architecture for isolating complex mechanisms of active materials that suffer from surface reconstruction and degradation in electrochemical cells.

25 ENERGY STORAGE↗