Engineering topics

Westphal, R. V.

Publications and source records attributed to Westphal, R. V..

At least 19 records

NASA NTRS1992

Measurements of the flow around a lifting-wing/body junction

Detailed measurements of all three mean velocity components and five of the six Reynolds stresses have been made around a model of a lifting-wing/body junction. The body was the flat working section floor of a small blower wind tunnel. Measurements of the surface pressure distribution on the NACA 0012 wing showed that the lift coefficient at the body surface was reduced by only 16 percent from the freestream value. It is shown that the near constancy of the bound vorticity requires the formation of aixal vorticity within the body boundary layer. This vorticity was concentrated in the two legs of the necklace vortex formed near the leading edge of the wing. The magnitude of the vorticity was always greater in the leg that developed on the suction surface. By four chord lengths downstream of the trailing edge, the turbulence structure of the suction leg was qualitatively similar to that of a single vortex imbedded in a turbulent boundary layer.

Wood, D. H.↗

NASA NTRS1991

Hybrid approach to data reduction for multi-sensor hot wires

A hybrid approach to implementing the calibration equations for a multisensor hot-wire probe is discussed. The approach combines some of the speed of a look-up approach with the moderate storage requirements of direct calculation based on functional fitting. Particular attention is given to timing and storage comparisons for an X-wire probe. The method depends on the oft-employed concept of an effective cooling velocity which is a function only of the bridge output voltage.

Hooper, C. L.↗

NASA NTRS1989

Subminiature Hot-Wire Probes

Class of improved subminiature hot-wire flow-measuring probes developed. Smaller sizes yield improved resolution in measurements of practical aerodynamic flows. Probe made in one-wire, two-perpendicular-wire, and three-perpendicular-wire version for measurement of one, two, or all three components of flow. Oriented and positioned on micromanipulator stage and viewed under microscope during fabrication. Tested by taking measurements in constant-pressure turbulent boundary layer. New probes give improved measurements of turbulence quantities near surfaces and anisotropies of flows strongly influence relative errors caused by phenomena related to spatial resolution.

Westphal, R. V.↗

NASA NTRS1989

Interaction of an oscillating vortex with a turbulent boundary layer

An oscillating vortex embedded within a turbulent boundary layer was generated experimentally by forcing a periodic lateral translation of a half-delta wing vortex generator. The objective of the experiment was to investigate the possibility that a natural oscillation, or meander, might be responsible for flattened vortex cores observed in previous work, which could also have contaminated previous turbulence measurements. The effect of this forced oscillation was characterized by comparison of measurements of the mean velocities and Reynolds stresses at two streamwise stations, for cases with and without forcing. The Reynolds stresses were affected significantly by the forced oscillation, mainly through contributions from the individual production terms, provided that the vortex was not too diffuse.

Westphal, R. V.↗

NASA NTRS1989

Fabrication and testing of subminiature multi-sensor hot-wire probes

A method for the fabrication of hot-wire sensors measuring 0.6 micron in diameter and 200 microns in length is described. This method allows accurate control of sensing-element orientation, thus making it possible to produce multisensor probes. Test results obtained with a miniature sensor fabricated by this method, for the outer region of a turbulent boundary layer developing in a zero presure gradient were compared to measurements from a conventional-sized probe made in the same flow, demonstrating that, because of their improved spatial resolution, subminiature sensors can provide more accurate measurements in boundary layers than do the conventional probes.

Ligrani, P. M.↗

NASA NTRS1989

Effect of velocity ratio on plane mixing layer development

An experimental study has been conducted to investigate the effect of velocity ratio on the development of a plane mixing layer to self-similarity. Plane mixing layers with five different velocity ratios (0.5, 0.6, 0.7, 0.8 and 0.9) were generated in a newly designed mixing layer wind tunnel with both initial boundary layers tripped. For each velocity ratio, mean flow and turbulence measurements were obtained at eight streamwise locations with a single cross-wire probe. The results indicate that the splittter plate wake plays a very dominant and, in some cases, a lasting role in the development of the mixing layer. For velocity ratios between 0.5 and 0.7, self-similarity of the mixing layer was observed with the asymptotic states comparable. Mixing layers with the higher velocity ratios failed to achieve a self-similar state within the measurement domain. The development distance decreased with increasing velocity ratio up to 0.7, after which it appeared to increase. Almost all of the observed effects may be attributed to the presence and subsequent behavior of the splitter plate wake.

Mehta, R. D.↗

NASA NTRS1989

A turbulent boundary layer at low Reynolds number with adverse pressure gradient

The evolution of a low Re(theta) turbulent boundary layer in an adverse pressure gradient (APG) is studied for comparison with CFD simulations by Spalart (1988). A short region of favorable pressure gradient is applied first to establish a self-preserving layer which is a suitable initial condition for the simulations. The APG is then applied rapidly such that Beta(x) of about 2 for Re(theta) of about 1500.

Watmuff, J. H.↗

NASA NTRS1988

Measurements of the free-stream fluctuations above a turbulent boundary layer

The paper describes an investigation of the velocity fluctuations in the free stream above an incompressible turbulent boundary layer developing at constant pressure. Measurements were performed in a wind tunnel with an rms level of axial velocity fluctuations of about 0.2 percent. The possibility of assessing the contributions to the rms level of the velocity fluctuations without using the high-pass filtering technique is demonstrated.

Wood, D. H.↗

NASA NTRS1988

Measurements of the Free-Stream Fluctuations above a Turbulent Boundary Layer

In this paper an investigation of the velocity fluctuations in the free stream above an incompressible turbulent boundary layer developing at constant pressure is described. It is assumed that the fluctuations receive contributions from three statistically independent sources: (1) one-dimensional unsteadiness, (2) free-stream turbulence, and (3) the irrotational motion induced by the turbulent boundary layer. Measurements were made in a wind tunnel with a root-mean-square level of the axial velocity fluctuations of about 0.2%. All three velocity components were measured using an X-wire probe. The unsteadiness was determined from the spanwise covariance of the axial velocity fluctuations, measured using two single-wire probes. The results show that it is possible to separate the contributions to the rms level of the velocity fluctuations without resorting to the dubious technique of high-pass filtering. This separation could be extended to the spectral densities of the contributions if measurements of sufficient accuracy were available.

Wood, D. H.↗

NASA NTRS1988

Velocity spectra in the irrotational flow outside a turbulent shear layer

The relationship between the spectra of the three normal stresses near a turbulent shear layer is derived from the constraint of irrotationality. The relationship implies that the common practice of determining time scales of the turbulence from spectra in the near field is not valid. This implication is reinforced by a discussion of the scaling of irrotational spectra that follows from the formulation of Phillips (1975).

Wood, D. H.↗

NASA NTRS1987

Skin friction measurements following manipulation of a turbulent boundary layer

Results are presented from three experiments in which direct, local measurements of the skin friction reduction due to flat-plate turbulence manipulators for overall viscous drag reduction were obtained. The results suggest that only a very small overall net drag reduction will be possible for such devices at moderate momentum thickness-derived Reynolds number values, since maximum skin friction drag is neither large nor sustained.

Nguyen, V. D.↗

NASA NTRS1986

The laser interferometer skin-friction meter - A numerical and experimental study

Limits to the applicability of thin-film lubrication theory are established. The following two problems are considered: (1) the response of the oil film to a time-varying skin friction such as is encountered in turbulent boundary layers, and (2) a 'surface-wave instability' encountered at high skin-friction levels. Results corresponding to the first problem reveal that the laser interferometer skin-friction meter may, in principle, be applied to the measurement of instantaneous skin friction. In addressing the second problem, it is shown that the observed surface waves are not the result of a hydrodynamic instability.

Murphy, J. D.↗

NASA NTRS1986

Improved Skin Friction Interferometer

An improved system for measuring aerodynamic skin friction which uses a dual-laser-beam oil-film interferometer was developed. Improvements in the optical hardware provided equal signal characteristics for each beam and reduced the cost and complexity of the system by replacing polarization rotation by a mirrored prism for separation of the two signals. An automated, objective, data-reduction procedure was implemented to eliminate tedious manual manipulation of the interferometry data records. The present system was intended for use in two-dimensional, incompressible flows over a smooth, level surface without pressure gradient, but the improvements discussed are not limited to this application.

Westphal, R. V.↗

NASA NTRS1986

Skin friction and Reynolds stress measurements for a turbulent boundary layer following manipulation using flat plates

Research has been undertaken to experimentally study the alterations in turbulent boundary-layer properties due to turbulence manipulation using thin flat plates. Plate geometry and placement within the boundary layer were selected to coincide with recent studies. Direct, local measurements of skin friction and Reynolds stresses were made within the boundary layer downstream of the manipulator devices for cases with an approach momentum thickness Reynolds number of 3700. A strong tendency for recovery of the Reynolds stresses was observed, accompanied by local skin-friction reductions of up to 15 percent. The mean velocity profile in the manipulated flow displayed the same similarity shape in the logarithmic region as a natural boundary layer, but had an enhanced wake component. The results indicate that the plate wake plays an important role in the boundary layer response to this sort of manipulation.

Westphal, R. V.↗

NASA NTRS1985

Double-branched vortex generator

In order to assess the suitability of using a double branched vortex generator in parametric studies involving vortex interactions, an experimental study of the main vortex and secondary flows produced by a double branched vortex generator was conducted in a 20-by-40 cm indraft wind tunnel. Measurements of the cross flow velocities were made with a five hole pressure probe from which vorticity contours and vortex parameters were derived. The results showed that the optimum configuration consisted of chord extensions with the absence of a centerbody.

Cantwell, E. R.↗

NASA NTRS1985

An experimental study of plane mixing layer development

Mean flow and turbulence was measured in the near field of two plane mixing layers in air with a maximum velocity of 21 m/sec. The experimental rig enabled mixing layers of velocity ratios 0 and 0.46 to be generated simultaneously. Gases with both tripped and untripped initial boundary layers were studied. It was found that the two stream layer developed to the self preserving state in a distance much shorter than did the single stream layer which followed accepted criteria for the development distance. The asymptotic levels of the turbulence quantities in the two stream layer and the development of the single stream layer showed agreement with existing data. It is suggested that the two stream mixing layer should provide a better test case for the development of turbulence models and calculation methods than the single stream mixing layer.

Mehta, R. D.↗

NASA NTRS1985

Interaction between a vortex and a turbulent boundary layer in a streamwise pressure gradient

The effect of a moderate adverse pressure gradient on the interaction between a single streamwise vortex and a turbulent boundary layer is investigated experimentally. Quantitative characterization of vortex properties based on measurements of the mean cross-flow velocity components is attained. Growth of the vortex core is observed, followed by a flattening of the core shape which occurs when the core radius becomes comparable to the distance of the vortex center from the surface. The adverse pressure gradient causes an increase in the rate of core growth and, therefore, a stronger distortion of the core shape. Turbulence properties are even more strongly disturbed by an adverse pressure gradient than by constant pressure.

Westphal, R. V.↗

NASA NTRS1984

Effect of initial conditions on turbulent reattachment downstream of a backward-facing step

The reattachment of a fully turbulent, two-dimentional shear layer downstream of a backward-facing step has been studied experimentally. The work examines the effect of variations in inlet conditions on the process of reattachment. A series of experiments was conducted in a low-speed wind tunnel using specialized instrumentation suited to the highly turbulent reversing flow near reattachment. Accurate characterization of the time-mean features of the reattaching flows was possible. Assuming linear scaling normalized on distance from reattachment, distributions of normalized pressure coefficient and forward flow fraction, and time-averaged skin friction coefficient appear universal for two-dimensional reattachment, independent of initial conditions and step height, for given duct geometry (area ratio) and for high step-height Reyolds numbers with thin separating boundary layers. The results suggest universal flow structure in the reattachment zone.

Westphal, R. V.↗