Search NASA⌕ Search

Engineering topics

White, B. R.

Publications and source records attributed to White, B. R..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Martian and Terrestrial Rock Abrasion from Wind Tunnel and Field Studies

Earth and Mars exhibit ventifacts, rocks that have been abraded by saltating sand. Previous theoretical and laboratory studies have determined abrasion susceptibilities of rocks as a function of sand type and impact angle and rock material strengths. For the last two years we have been engaged in wind tunnel and field studies to better understand the fundamental factors which control and influence rock abrasion and ventifact formation on Earth and Mars. In particular, we are examining: 1) What types of rocks (composition, texture, and shape) preferentially erode and what are the relative rates of one type vs. another? 2) What are the controlling factors of the aeolian sand cloud (flux, particle speed, surface roughness, etc) which favor rock abrasion?, 3) How do specific ventifact characteristics tie into their mode of formation and rock properties? We find several important factors: 1) Initial rock shape controls the rate of abrasion, with steeper faces abrading faster than shallower ones. The relationship is partly dependent on angle-dependent flux (proportional to sin[theta]) but exhibits additional non-linear effects from momentum transfer efficiency and rebound effects that vary with incidence angle. 2) Irregular targets with pits or grooves abrade at greater rates than targets with smooth surfaces, with indentations generally enlarging with time. Surfaces become rougher with time. 3) Targets also abrade via slope retreat, which is roughly dependent on the slope of the front face. The formation of basal sills is common, as observed on terrestrial and Martian ventifacts.

Bridges, N. T.↗
NASA NTRS1991

Relationships between topographic roughness and aeolian processes

The interaction between winds and desert surfaces has important implications for sediment transport on Earth, Mars, and Venus, and for understanding the relationships between radar backscatter and aerodynamic roughness as part of the NASA Shuttle Imaging radar (SIR-C) Mission. Here, researchers report results from measurements of boundary layer wind profiles and surface roughness at sites in Death Valley and discuss their implications. The sites included a flat to undulating gravel and sand reg, alluvial fans, and a playa. Estimates of average particle size composition of Death Valley sites and arithmetic mean values of aerodynamic roughness are given in tabular form.

Greeley, Ronald↗
NASA NTRS1988

Dynamic shear of granular material under variable gravity conditions

This paper describes some experiments with granular materials which recently have been conducted aboard the NASA KC-135 aircraft during variable gravity maneuvers. The main experimental apparatus consisted of a small drum containing granular material which was rotated slowly while the angle assumed by the slip surface with respect to the horizontal was observed and recorded photographically. Conventional wisdom has held that this 'dynamic angle of response' was a material constant, independent of (among other things) gravitational level. The results presented here are quite contrary, suggesting instead an angle that varies with the reciprocal of the square root of gravity. This finding may have important consequences on the understanding of many active processes in Planetary Geology involving granular materials and may provide qualitative confirmation of some of the theoretical predictions of modern models of granular shear flows.

White, B. R.↗
NASA NTRS1987

An investigation of turbulence structure in a low-Reynolds-number incompressible turbulent boundary

An existing high turbulence intensity level (5%) atmospheric boundary-layer wind tunnel has been successfully converted to a relatively low level turbulence (0.3%) wind tunnel through extensive modification, testing, and calibration. A splitter plate was designed, built, and installed into the wind-tunnel facility to create thick, mature, two-dimensional turbulent boundary layer flow at zero pressure gradient. Single and cross hot-wire measurements show turbulent boundary layer characteristics of good quality with unusually large physical size, i.e., viscous sublayer of the order of 1 mm high. These confirm the potential ability of the tunnel to be utilized for future high-quality near-wall turbulent boundary layer measurements. It compares very favorably with many low turbulence research tunnels.

White, B. R.↗
NASA NTRS1987

A low-density boundary-layer wind tunnel facility

This abstract describes a low-density wind-tunnel facility that was established at NASA Ames in order to aid interpretation and understanding of data received from the Mariner and Viking spacecraft through earth-based simulation. The wind tunnel is a boundary-layer type which is capable of operating over a range of air densities ranging from 0.01 to 1.24 kg/cu m, with the lower values being equivalent to the near-surface density of the planet Mars. Although the facility was developed for space and extraterrestrial simulation, it also can serve as a relatively large-scale, low-density aerodynamic test facility. A description of this unique test facility and some Pitot-tube and hot-wire anemometry data acquired in the facility are presented.

White, B. R.↗
NASA NTRS1986

Aeolian processes aboard a space station: Saltation and particle trajectory analysis

The Carousel wind tunnel (CWT) proposed to study aeolian processes aboard a space station consists of two concentric rotating drums. The space between the two drums comprises the wind tunnel test section. Differential rates of rotation of the two drums would provide a wind velocity with respect to either drum surface. Preliminary results of measured velocity profiles made in a CWT prototype indicate that the wall bounded boundary layer profiles are suitable to simulate flat plate turbulent boundary layer flow. The two dimensional flat plate Cartesian coordinate equations of motion of a particle moving through the air are explained. In order to assess the suitability of CWT in the analysis of the trajectories of windblown particles, a series of calculations were conducted comparing cases for gravity with those of zero gravity. Results from the calculations demonstrate that a wind tunnel of the carousel design could be fabricted to operate in a space station environment and that experiments could be conducted which would yield significant results contributing to the understanding of the physics of particle dynamics.

White, B. R.↗
NASA NTRS1984

Numerical and experimental studies of particle flow in a high-pressure boundary-layer wind tunnel

The approach was to simulate the surface environment of Venus as closely as practicable and to conduct experiments to determine threshold wind speeds, particle flux, particle velocities, and the characteristics of various aeolian bedforms. The Venus Wind Tunnel (VWT) is described and the experimental procedures that were developed to make the high-pressure wind tunnel measurements are presented. In terrestrial simulations of aeolian activity, it is possible to conduct experiments under pressures and temperatures found in natural environments. Because of the high pressures and temperatures, Venusian simulations are difficult to achieve in this regard. Consequently, extrapolation of results to Venue potentially involves unknown factors. The experimental rationale was developed in the following way: The VWT enables the density of the Venusian atmosphere to be reproduced. Density is the principal atmospheric property for governing saltation threshold, particle flux, and the ballistics of airborne particles (equivalent density maintains dynamic similarity of gas flow). When operated at or near Earth's ambient temperature, VWT achieves Venusian atmospheric density at pressures of about 30 bar, or about one third less than those on Venus, although still maintaining dynamic similarity to Venus.

White, B. R.↗
NASA NTRS1984

Abrasion by aeolian particles: Earth and Mars

Estimation of the rate of aeolian abrasion of rocks on Mars requires knowledge of: (1) particle flux, (2) susceptibilities to abrasion of various rocks, and (3) wind frequencies on Mars. Fluxes and susceptibilities for a wide range of conditions were obtained in the laboratory and combined with wind data from the Viking meteorology experiment. Assuming an abundant supply of sand-sized particles, estimated rates range up to 2.1 x 10 to the minus 2 power cm of abrasion per year in the vicinity of Viking Lander 1. This rate is orders of magnitude too great to be in agreement with the inferred age of the surface based on models of impact crater flux. The discrepancy in the estimated rate of abrasion and the presumed old age of the surface cannot be explained easily by changes in climate or exhumation of ancient surfaces. The primary reason is thought to be related to the agents of abrasion. At least some sand-sized (approx. 100 micrometers) grains appear to be present, as inferred from both lander and orbiter observations. High rates of abrasion occur for all experimental cases involving sands of quartz, basalt, or ash. However, previous studies have shown that sand is quickly comminuted to silt- and clay-sized grains in the martian aeolian regime. Experiments also show that these fine grains are electrostatically charged and bond together as sand-sized aggregates. Laboratory simulations of wind abrasion involving aggregates show that at impact velocities capable of destroying sand, aggregates from a protective veneer on the target surface and can give rise to extremely low abrasion rates.

Greeley, R.↗
NASA NTRS1982

Rate of wind abrasion on Mars

A brief description is given of the experiments performed to obtain data on windblown particles and abrasion of rocks in a simulated Martian environment. Preliminary results are presented and combined with Viking meteorological data in estimating rates of wind abrasion at the VL-1 site on Mars. Attention is also given to the implications that the results have for Martian surface history. Calculations of the present rates of abrasion by windblown particles on Mars yield values ranging from 0.021 cm/yr to nearly zero, depending on the target, the agent of abrasion, and the availability of windblown particles.

Greeley, R.↗
NASA NTRS1981

Venusian saltation

Numerical solutions are given for particle trajectory equations of motion for the surface of Venus. Particles in saltation obtain maximum heights of two or less centimeters, and have path lengths of less than a meter regardless of particle diameter. The saltation process and particle trajectories are found insensitive to surface pressure changes over the range of 70 to 100 bars, and temperature changes over the range of 600 to 900 K. Due to dense atmosphere, the net rate of surface material transport due to saltation is small for particles in diameters from 0.01 to 7 mm, as compared to earth which has 10 times more, and Mars which has 250 times more. Path length scales are also found to be very small, suggesting the presence of dunes on Venus; however, there is still a possibility that small ripples do exist, which cannot be detected by high-resolution radar images.

White, B. R.↗
NASA NTRS1979

Soil transport by winds on Mars

Results of low-pressure wind tunnel testing and theoretical considerations are used to estimate the eolian transport of surface material on Mars. Saltation on Mars, equations of particle motion, computational results, and analytical determination of surface material movement are considered. A semiempirical formula is developed for estimating the total amount of surface material moving in eolian saltation, surface traction, and suspension. Numerical solutions of the equations of motion for particle trajectories on the surface of Mars are presented. The ratio of final particle speed to the particle threshold friction speed is found to be several times that of saltation on earth

White, B. R.↗
NASA NTRS1979

Low-Reynolds-number turbulent boundary layers

A test facility operating at substantially reduced pressures is described and shown to be suitable when used with an open-circuit turbulent boundary layer wind tunnel. The facility is capable of producing flows with momentum Reynolds number in the range 200-10,000 by varying the ambient pressure. At low-Reynolds-number flows the pressure is low enough to allow the tunnel to operate with large values of freestream speed. The tunnel's reliability is verified by examining flows where momentum Reynolds number is greater than 1200. The results skin friction coefficients, wake parameters, and basic velocity profiles - consistently agreed with well-established data. For momentum Reynolds number from 600 through 1200 the resulting data indicate that the 'universal velocity profile' is accurate and correctly describes the mean flow properties. For Reynolds number from 425 through 600, the viscous sublayer in this range can no longer maintain its characteristic size.

White, B. R.↗
NASA NTRS1977

Dust storms on Mars: Considerations and simulations

Aeolian processes are important in modifying the surface of Mars at present, and appear to have been significant in the geological past. Aeolian activity includes local and global dust storms, the formation of erosional features such as yardangs and depositional features such as sand dunes, and the erosion of rock and soil. As a means of understanding aeolian processes on Mars, an investigation is in progress that includes laboratory simulations, field studies of earth analogs, and interpretation of spacecraft data. This report describes the Martian Surface Wind Tunnel, an experimental facility established at NASA-Ames Research Center, and presents some results of the general investigation. Experiments dealing with wind speeds and other conditions required for the initiation of particle movement on Mars are described and considerations are given to the resulting effectiveness of aeolian erosion.

Greeley, R.↗
NASA NTRS1976

Estimated grain saltation in a Martian atmosphere

Mariner 9 spacecraft images showing evidence of variable surface features and surface erosion resulting from atmospheric wind on Mars have caused a renewed interest in the eolian mechanics of saltating grains. To study this phenomenon, both experimental investigation in an atmospheric wind tunnel and numerical solutions of the equations of motion of a single grain under Martian surface conditions were conducted. The numerical solutions for earth were used and empirically adjusted to correlate with existing experimental data for Mars. These modified equations were then solved to estimate grain motion for Mars. These calculations show the importance of a lifting force on the grain to initiate motion in both earth and Mars calculations. Major findings include a comparison of earth and Mars grain trajectories that show Mars length scales to be longer and to fall with a higher terminal grain velocity. The grains in the Mars calculation also made a smaller collision angle with the surface on rebound.

White, B. R.↗
NASA NTRS1976

Saltation threshold on Mars - The effect of interparticle force, surface roughness, and low atmospheric density

Results are reported for wind-tunnel experiments performed to determine the threshold friction speed of particles with different densities. Experimentally determined threshold speeds are plotted as a function of particle diameter and in terms of threshold parameter vs particle friction Reynolds number. The curves are compared with those of previous experiments, and an A-B curve is plotted to show differences in threshold speed due to differences in size distributions and particle shapes. Effects of particle diameter are investigated, an expression for threshold speed is derived by considering the equilibrium forces acting on a single particle, and other approximately valid expressions are evaluated. It is shown that the assumption of universality of the A-B curve is in error at very low pressures for small particles and that only predictions which take account of both Reynolds number and effects of interparticle forces yield reasonable agreement with experimental data. Effects of nonerodible surface roughness are examined, and threshold speeds computed with allowance for this factor are compared with experimental values. Threshold friction speeds on Mars are then estimated for a surface pressure of 5 mbar, taking into account all the factors considered.

Iversen, J. D.↗