Soot Formation and Precursor Chemistry in Counterflow Flames of Aviation Fuels Surrogates
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Whitesides, R.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
In the present work, a central fuel property hypothesis (CFPH), which states that fuel properties are sufficient to provide an indication of a fuel's performance irrespective of its chemical composition, was numerically investigated In particular, the objective of the study was to determine whether Research Octane Number (RON) and Motor Octane Number (MON), as fuel properties, are sufficient to describe a fuel's knock-limited performance under boosted spark-ignition (SI) conditions within the framework of CFPH. To this end, four TPRF-bioblendstock surrogates having different compositions but matched RON (= 98) and MON (= 90), were first generated using a non-linear regression model based on artificial neural network (ANN). Three unconventional bioblendstocks were included in the analysis: Di-isobutylene (DIB), Isobutanol and Anisole. Skeletal reaction mechanisms were generated for the TPRF-DIB, TPRF-isobutanol and TPRF-anisole blends from a detailed kinetic mechanism. Thereafter, numerical simulations were performed for the fuel surrogates using the skeletal mechanisms and a virtual cooperative fuel research (CFR) engine model, under a representative boosted operating condition. In the computational fluid dynamics (CFD) model, the G-equation approach was employed to track the turbulent flame front and the well-stirred reactor model combined with multi-zone binning strategy was used to capture auto-ignition in the end-gas. In addition, laminar flame speed was tabulated for each blend as a function of pressure, temperature and equivalence ratio a priori, and the lookup tables were used to prescribe laminar flame speed as an input to the G-equation model. Parametric spark timing sweeps were performed for each fuel blend to determine the corresponding knock-limited spark advance (KLSA) and 50% burn point (CA50) at the respective KLSA timing. It was observed that despite same RON, MON and engine operating conditions, the TPRF-Anisole blend exhibited markedly different knock-limited performance from the other three blends. This deviation from the octane index (DI) expectation was shown to be caused by differences in laminar flame speed (LFS). However; it was found that relatively large fuel-specific differences in LFS (> 20%) would have to be present to cause any appreciable deviation from the 01 framework. Otherwise, RON and MON would still be robust enough to predict a fuel's knock-limited performance.
Abstract not provided
A methodology for modeling gaseous injection has been refined and applied to recent experimental data from the literature. This approach uses a discrete phase analogy to handle gaseous injection, allowing for addition of gaseous injection to a CFD grid without needing to resolve the injector nozzle. This paper focuses on model testing to provide the basis for simulation of hydrogen direct injected internal combustion engines. The model has been updated to be more applicable to full engine simulations, and shows good agreement with experiments for jet penetration and time-dependent axial mass fraction, while available radial mass fraction data is less well predicted.
New simulations of graphene growth in flame environments are presented. The simulations employ a kinetic Monte Carlo (KMC) algorithm coupled to molecular mechanics (MM) geometry optimization to track individual graphenic species as they evolve. Focus is given to incorporation of five-member rings and resulting curvature and edge defects. The model code has been re-written to be more computationally efficient enabling a larger set of simulations to be run, decreasing stochastic fluctuations in the averaged results. The model also includes updated rate coefficients for graphene edge reactions recently published in the literature. The new simulations are compared to results from the previous model as well as to hydrogen to carbon ratios recorded in experiment and calculated with alternate models.
A new diffusion Monte Carlo study is performed on the isomers of C{sub 4}H{sub 3} and C{sub 4}H{sub 5} emulating the methodology of a previous study [Int. J. Chem. Kinetics 33, 808 (2001)]. Using the same trial wave function form of the previous study, substantially different isomerization energies were found owing to the use of larger walker populations in the present work. The energy differences between the E and I isomers of C{sub 4}H{sub 3} were found to be 10.5 {+-} 0.5 kcal/mol and for C{sub 4}H{sub 5}, 9.7 {+-} 0.6 kcal/mol. These results are in reasonable accord with recent MRCI and CCSD(T) findings.
Reaction pathways are presented for hydrogen-mediated isomerization of a five and six member carbon ring complex on the zigzag edge of a graphene layer. A new reaction sequence that reverses orientation of the ring complex, or 'flips' it, was identified. Competition between the flip reaction and 'ring separation' was examined. Ring separation is the reverse of the five and six member ring complex formation reaction, previously reported as 'ring collision'. The elementary steps of the pathways were analyzed using density-functional theory (DFT). Rate coefficients were obtained by solution of the energy master equation and classical transition state theory utilizing the DFT energies, frequencies, and geometries. The results indicate that the flip reaction pathway dominates the separation reaction and should be competitive with other pathways important to the graphene zigzag edge growth in high temperature environments.