Engineering topics

Widnall, S. E.

Publications and source records attributed to Widnall, S. E..

At least 19 records

NASA NTRS1986

Calculations of axisymmetric vortex sheet roll-up using a panel and a filament model

A method for calculating the self-induced motion of a vortex sheet using discrete vortex elements is presented. Vortex panels and vortex filaments are used to simulate two-dimensional and axisymmetric vortex sheet roll-up. A straight forward application using vortex elements to simulate the motion of a disk of vorticity with an elliptic circulation distribution yields unsatisfactroy results where the vortex elements move in a chaotic manner. The difficulty is assumed to be due to the inability of a finite number of discrete vortex elements to model the singularity at the sheet edge and due to large velocity calculation errors which result from uneven sheet stretching. A model of the inner portion of the spiral is introduced to eliminate the difficulty with the sheet edge singularity. The model replaces the outermost portion of the sheet with a single vortex of equivalent circulation and a number of higher order terms which account for the asymmetry of the spiral. The resulting discrete vortex model is applied to both two-dimensional and axisymmetric sheets. The two-dimensional roll-up is compared to the solution for a semi-infinite sheet with good results.

Kantelis, J. P.↗

NASA NTRS1986

Energetics and optimum motion of oscillating lifting surfaces of finite span

In certain modes of animal propulsion in nature, such as bird flight and fish swimming, the efficiency compared to man-made vehicles is very high. In such cases, wing and tail motions are typically associated with relatively high Reynolds numbers, where viscous effects are confined to a thin boundary layer at the surface and a thin trailing wake. The propulsive forces, which are generated primarily by the inertial forces, can be calculated from potential-flow theory using linearized unsteady-wing theory (for small-amplitude oscillations). In the present study, a recently developed linearized, low-frequency, unsteady lifting-line theory is employed to calculate the (sectional and total) energetic quantities and optimum motion of an oscillating wing of finite span.

Ahmadi, A. R.↗

NASA NTRS1985

A panel method study of vortex sheets with special emphasis on sheets of axisymmetric geometry

The self induced evolution of a vortex sheet was simulated by modeling the sheet using an integration of discrete elements of vorticity. Replacing small sections of a vortex sheet by flat panels of constant vorticity is found to reproduce more accurately the initial conditions for the Lagrangian simulation technique than replacement by point vortices. The flat panel method for the vortex sheet was then extended to model axisymmetric vortex sheets. The local and far field velocities induced by the axisymmetric panels were obtained using matched asymptotic analysis, and some of the uncertainties involved in other models of the axisymmetric vortex sheet have been eliminated. One important result of this analysis is the determination of the proper choice of core size for a circular vortex filament which may replace a section of an axisymmetric vortex sheet. Roll-up of both two dimensional and axisymmetric vortex sheets was computed using the panel methods developed in the report.

Sugioka, I.↗

NASA NTRS1985

Unsteady lifting-line theory as a singular-perturbation problem

Unsteady lifting-line theory is developed for a wing of large aspect ratio oscillating at low frequency in inviscid incompressible flow. The wing is assumed to have a rigid chord but a flexible span. Use of the method of matched asymptotic expansions reduces the problem from a singular integral equation to quadrature. The pressure field and airloads, for a prescribed wing shape and motion, are obtained in closed form as expansions in inverse aspect ratio. A rigorous definition of unsteady induced downwash is also obtained. Numerical calculations are presented for an elliptic wing in pitch and heave; compared with numerical lifting-surface theory, computation time is reduced significantly. The present work also identifies and resolves errors in the unsteady lifting line theory of James (1975), and points out a limitation in that of Van Holten (1975, 1976, 1977).

Ahmadi, A.↗

NASA NTRS1983

An aeroacoustic model for high-speed, unsteady blade-vortex interaction

A three-dimensional aeroacoustic model is developed to predict the sound pulse radiated by the passage of a helicopter blade over a potential vortex. The linearized analysis assumes that either the blade-vortex separation is small or that the blade-tip Mach number is close to 1, or both, so that an acoustically noncompact situation exists. The three-dimensional blade loading due to blade-vortex interaction is constructed through a spanwise superposition of two-dimensional solutions with strength linearly increasing from hub to tip. Such a loading overestimates somewhat the strength of tip region dipoles in the acoustic calculation that follows. The final expression for the predicted far-field signature is obtained in closed form, and thus permits a relatively inexpensive calculation of the directivity of peak acoustic pressures in three dimensions.

Martinez, R.↗

NASA NTRS1983

Energetics and optimum motion of oscillating lifting surfaces

Low-frequency, unsteady, lifting-line theory is used to characterize the energetics and optimum motion of an unswept rigid wing oscillating harmonically in an inviscid, incompressible flow. The energetics calculations account for the leading edge suction force, the power absorbed in the wing oscillations, and the energy loss rate produced by vortex shedding. Optimization is achieved by minimizing the average energy loss rate in relation to a given thrust, and a unique solution is found in the three dimensional case for low, reduced frequencies. The two-dimensional solution is nonunique, a condition which is examined in terms of the normal modes of the energy loss rate matrix. An invisible mode with a hydrodynamic efficiency of 100 pct is obtained in the two-dimensional case, causing the nonuniqueness of the solution by yielding no fixed positive thrust through perfect unsteady feathering.

Ahmadi, A. R.↗

NASA NTRS1983

Aerodynamic theory for wing with side edge passing subsonically through a gust

An approximate solution for the unsteady loading near the square-shape tip of a wing passing through an oblique gust is obtained in closed form. The aerodynamic theory developed can be used to predict airloads felt by a helicopter blade experiencing a blade/vortex interaction for high blade tip speed and/or for small vertical blade/vortex separation. Under these conditions one can show that the blade's trailing edge has little influence on the character of the chordwise loading at all spanwise sections; thus, the chord may be allowed to extend to infinity in the downstream direction. Therefore, the model considered here is that of a quarter-infinite flat plate wing with side edge passing subsonically through an oblique gust.

Martinez, R.↗

NASA NTRS1982

Unsteady lifting-line theory with applications

Unsteady lifting-line theory is developed for a flexible unswept wing of large aspect ratio oscillating at low frequency in inviscid incompressible flow. The theory is formulated in terms of the acceleration potential and treated by the method of matched asymptotic expansions. The wing displacements are prescribed and the pressure field, airloads, and unsteady induced downwash are obtained in closed form. Sample numerical calculations are presented. The present work identifies and resolves errors in the unsteady lifting-line theory of James and points out a limitation in that of Van Holten. Comparison of the results of Reissner's approximate unsteady lifting-surface theory with those of the present work shows favorable agreement. The present work thus provides some formal justification for Reissner's ad hoc theory. For engineering purposes, the region of applicability of the theory in the reduced frequency-aspect ratio domain is identified approximately and found to cover most cases of practical interest.

Ahmadi, A. R.↗

NASA NTRS1981

Aeroacoustic theory for noncompact wing-gust interaction

Three aeroacoustic models for noncompact wing-gust interaction were developed for subsonic flow. The first is that for a two dimensional (infinite span) wing passing through an oblique gust. The unsteady pressure field was obtained by the Wiener-Hopf technique; the airfoil loading and the associated acoustic field were calculated, respectively, by allowing the field point down on the airfoil surface, or by letting it go to infinity. The second model is a simple spanwise superposition of two dimensional solutions to account for three dimensional acoustic effects of wing rotation (for a helicopter blade, or some other rotating planform) and of finiteness of wing span. A three dimensional theory for a single gust was applied to calculate the acoustic signature in closed form due to blade vortex interaction in helicopters. The third model is that of a quarter infinite plate with side edge through a gust at high subsonic speed. An approximate solution for the three dimensional loading and the associated three dimensional acoustic field in closed form was obtained. The results reflected the acoustic effect of satisfying the correct loading condition at the side edge.

Martinez, R.↗

NASA NTRS1981

Prediction of low frequency and impulsive sound radiation from horizontal axis wind turbines

Theoretical models to predict the radiation of low frequency and impulsive sound from horizontal axis wind turbines due to three sources: (1) steady blade loads; (2) unsteady blade loads due to operation in a ground shear; (3) unsteady loads felt by the blades as they cross the tower wake. These models are then used to predict the acoustic output of MOD-1, the large wind turbine operated near Boone, N.C. Predicted acoustic time signals are compared to those actually measured near MOD-1 and good agreement is obtained.

Martinez, R.↗

NASA NTRS1980

Effect of tip vortex structure on helicopter noise due to blade-vortex interaction

A potential cause of helicopter impulsive noise, commonly called blade slap, is the unsteady lift fluctuation on a rotor blade due to interaction with the vortex trailed from another blade. The relationship between vortex structure and the intensity of the acoustic signal is investigated. Unsteady lift on the blades due to blade-vortex interaction is calculated using linear unsteady aerodynamic theory, and expressions are derived for the directivity, frequency spectrum, and transient signal of the radiated noise. The inviscid rollup model of Betz is used to calculate the velocity profile in the trailing vortex from the spanwise distribution of blade tip loading. A few cases of tip loading are investigated, and numerical results are presented for the unsteady lift and acoustic signal due to blade-vortex interaction. The intensity of the acoustic signal is shown to be quite sensitive to changes in tip vortex structures.

Widnall, S. E.↗

NASA NTRS1980

Unified aerodynamic-acoustic theory for a thin rectangular wing encountering a gust

A linear aerodynamic-acoustic theory is developed for the prediction of the surface pressure distribution and three-dimensional acoustic far-field for a flat plate rectangular wing encountering a stationary short-wavelength oblique gust. It is suggested that for an infinite-span wing, leading- and trailing-edge responses to a short-wavelength gust are essentially independent. This idea is used to solve for the two-dimensional pressure field due to the passage of an infinite-span wing through an oblique gust. By allowing the field point to come down to the wing's surface, one finds an expression for the surface pressure distribution which agrees with that given in the two-dimensional aerodynamic theories of Amiet and Adamczyk. Spanwise Fourier superposition of two-dimensional solutions to the infinite-span wing problem is used to approximate the three-dimensional acoustic field due to the interaction of a stationary oblique gust with a flat-plate rectangular wing traveling at a subsonic speed.

Martinez, R.↗

NASA NTRS1980

Examination of group-velocity criterion for breakdown of vortex flow in a divergent duct

A group-velocity criterion for vortex breakdown implied by wave trapping theory is applied to vortex flows in a slightly divergent duct that exhibits breakdown. The group velocities for both symmetric (n = 0) and nonsymmetric (n = plus or - 1) modes of wave propagation are calculated for the experimental data. It is found that the flow ahead of the breakdown region is always supercritical and stable to these modes of disturbances. However, the flow field behind the breakdown region may be either supercritical or subcritical to the modes n = 0 and n = 1, and always supercritical to mode n = -1. The flow field behind this breakdown region is unstable to the asymmetric mode disturbance (n = 1) for a finite range of wavenumbers. The calculated frequencies of the unstable disturbances are in good agreement with the frequencies obtained from the experimental measurements.

Tsai, C.-Y.↗

NASA NTRS1979

A group-velocity criterion for breakdown of vortex flow: An application to measured inlet profiles

Vortex flows exhibiting breakdown in a slightly divergent duct were measured. The slowly varying vortex flow field downstream of the entrance and upstream of the breakdown region is obtained numerically by using the inviscid quasi-cylindrical approximation. In these calculations, the Faler and Lebovich's experimental data were used as the starting conditions at the entrance of the duct. The group velocity of wave propagation for the axisymmetric mode (n = 0) and the asymmetric modes (n = + or - 1 and n = + or - 2) are calculated for the entrance conditions. For the theoretically predicted slowly varying flow field downstream of the entrance, the wave characteristics of the n = 0 and n = + or - 1 modes are presented. It was concluded that the flows which subsequently undergo vortex breakdown are all predicted to be supercritical and stable to infinitesimal inviscid disturbances, including the axially symmetric as well as the nonsymmetric perturbations.

Tsai, C. Y.↗

NASA NTRS1979

An examination of a group-velocity criterion for the breakdown of an idealized vortex flow

The phenomenon of vortex breakdown is believed to be associated with a finite amplitude wave that has become trapped at the critical or breakdown location. The conditions at which the propagating waves become trapped at a certain axial location were examined by use of a group-velocity criterion implied by Landahl's general theory of wave trapping. An ideal vortex having constant vorticity and uniform axial velocity at the inlet of a slowly diverging duct was studied. The linear wave propagation analysis is applied to the base flow at several axial stations for several values of the ratio of swirl velocity to axial velocity at the inlet of the divergent duct, assuming a locally parallel flow. The dipsersion relations and hence the group velocities of both the symmetric (n = 0) and asymmetric modes (n = + or - 1) were investigated. The existence of a critical state in the flow (at which the group velocity vanishes), and its relationship to the stagnation point on the axis of the duct and to the occurrence of an irregular singularity in the equations governing wave propagation in the flow field are discussed.

Tsai, C. Y.↗

NASA NTRS1978

The effect of tip vortex structure on helicopter noise due to blade/vortex interaction

A potential cause of helicopter impulsive noise, commonly called blade slap, is the unsteady lift fluctuation on a rotor blade due to interaction with the vortex trailed from another blade. The relationship between vortex structure and the intensity of the acoustic signal is investigated. The analysis is based on a theoretical model for blade/vortex interaction. Unsteady lift on the blades due to blade/vortex interaction is calculated using linear unsteady aerodynamic theory, and expressions are derived for the directivity, frequency spectrum, and transient signal of the radiated noise. An inviscid rollup model is used to calculate the velocity profile in the trailing vortex from the spanwise distribution of blade tip loading. A few cases of tip loading are investigated, and numerical results are presented for the unsteady lift and acoustic signal due to blade/vortex interaction. The intensity of the acoustic signal is shown to be quite sensitive to changes in tip vortex structure.

Wolf, T. L.↗

NASA NTRS1977

The instability of the thin vortex ring of constant vorticity

A theoretical study indicating that vortex rings at moderate Reynolds numbers are unstable to azimuthal bending waves is presented. Only the case of a thin vortex ring with a core of constant vorticity in an inviscid flow is examined. The disturbance flow and the mean flow of the vortex ring are derived as asymptotic solutions near the core; the stability analysis is developed completely for a certain class of bending waves that are unstable on a line filament in the presence of strain. The vortex ring is found to be always unstable for at least two wavenumbers for which waves on a line filament of the same vorticity distribution would not rotate. Published experimental results are cited to support these conclusions.

Widnall, S. E.↗

NASA NTRS1976

An experimental study of helicopter rotor rotational noise in a wind tunnel

The rotational noise of model helicopter rotors in forward flight was studied in an anechoic wind tunnel. The parameters under study were the rotor thrust (blade loading), blade number and advance ratio. The separate effects of each parameter were identified with the other parameters being held constant. The directivity of the noise was also measured. Twelve sets of data for rotational noise as a function of frequency were compared with the theory of Lowson and Ollerhead. In general, the agreement is reasonably good, except for the cases of (1) low and high disk loadings, (2) the four bladed rotor, and (3) low advance ratios. The theory always under-estimates the rotational noise at high harmonics.

Lee, A.↗