Search NASA⌕ Search

Engineering topics

Wiens, Roger C.

Publications and source records attributed to Wiens, Roger C..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Characterization of SimulCam, a standoff Raman system for scientific support of SuperCam operations on Mars

During the development activities of SuperCam Calibration Target, target intended for one of the two first Raman instruments to be deployed on another planetary body, our group developed a laboratory instrument that could simulate to some extent the Raman capabilities of one of such instruments and could provide data with similar quality. The use of this kind of laboratory instruments has demonstrated its utility in the evaluation of potential calibration targets or anticipating the science outcome that an instrument could provide. The present work describes our laboratory setup to support SuperCam, evaluating similarities between both instruments, despite of differences in the hardware. Evaluation of data gathered by SuperCam on Mars and the availability of one replica of SuperCam’s Calibration Target allowed the comparison on the same set of targets, demonstrating how similar Signal-to-Noise Ratio (SNR) could be achieved from both instruments. The higher energy per pulse on SimulCam is compensated by a greater analytical footprint and the use of smaller collection optics. The results show how spectra obtained at representative distances of SuperCam are comparable. Operational principles are also comparable in terms of time resolution, and close in terms of spectral resolution. This similarity has allowed different science support works using SimulCam data, as well as the support to Mars detections using our setup. We provide examples of this support that will be shared with the community in different papers, as well as examples of possible operations activities that could benefit from experiments performed with SimulCam. We show how this setup can complement the two laboratory replicas in Los Alamos and Toulouse in providing support data to different experiments.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Manganese-rich sandstones as an indicator of ancient oxic lake water conditions in Gale crater, Mars

Manganese has been observed on Mars by the NASA Curiosity rover in a variety of contexts and is an important indicator of redox processes in hydrologic systems on Earth. Within the Murray formation, an ancient primarily fine-grained lacustrine sedimentary deposit in Gale crater, Mars, have observed up to 45× enrichment in manganese and up to 1.5× enrichment in iron within coarser grained bedrock targets compared to the mean Murray sediment composition. This enrichment in manganese coincides with the transition between two stratigraphic units within the Murray: Sutton Island, interpreted as a lake margin environment, and Blunts Point, interpreted as a lake environment. On Earth, lacustrine environments are common locations of manganese precipitation due to highly oxidizing conditions in the lakes. Here, we explore three mechanisms for ferromanganese oxide precipitation at this location: authigenic precipitation from lake water along a lake shore, authigenic precipitation from reduced groundwater discharging through porous sands along a lake shore, and early diagenetic precipitation from groundwater through porous sands. All three scenarios require highly oxidizing conditions and we discuss oxidants that may be responsible for the oxidation and precipitation of manganese oxides. This work has important implications for the habitability of Mars to microbes that could have used Mn redox reactions, owing to its multiple redox states, as an energy source for metabolism.

58 GEOSCIENCES↗
DOE OSTI2024

Sub-Diurnal Methane Variations on Mars Driven by Barometric Pumping and Planetary Boundary Layer Evolution

In recent years, the Tunable Laser Spectrometer within the Sample Analysis at Mars (TLS-SAM) instrument on board the Mars Science Laboratory (MSL) Curiosity rover has detected methane variations in the atmosphere at Gale crater. Methane concentrations appear to fluctuate seasonally as well as sub-diurnally, which is difficult to reconcile with an as-yet-unknown transport mechanism delivering the gas from underground to the atmosphere. To potentially explain the fluctuations, we consider barometrically induced transport of methane from an underground source to the surface, modulated by temperature-dependent adsorption. The subsurface fractured-rock seepage model is coupled to a simplified 1-D atmospheric mixing model to provide insights on the pattern of atmospheric methane concentrations in response to transient surface methane emissions, as well as to predict sub-diurnal variation in methane abundance for the northern summer period, which is a candidate time frame for a MSL Curiosity sampling campaign. Our analysis suggests that there is a lower limit to the subsurface fracture density that can produce the observed methane patterns, below which the atmospheric methane variations would be out of phase with the observations. The best-performing model scenarios indicate a significant, short-lived methane pulse just prior to sunrise, the detection of which by TLS-SAM would be a potential indicator of the contribution of barometric pumping to Mars' atmospheric methane variations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

An acoustic investigation of the near-surface turbulence on Mars

The Perseverance rover is carrying out an original acoustic experiment on Mars: the SuperCam microphone records the spherical acoustic waves generated by laser sparks at distances from 2 m to more than 8 m. These N-shaped acoustic waves scatter from the multiple local heterogeneities of the turbulent atmosphere. Therefore, large and random fluctuations of sound travel time and intensity develop as the waves cross the medium. The variances of the travel times and the scintillation index (normalized variance of the sound intensity) are studied within the mathematical formalism of the propagation of spherical acoustic waves through thermal turbulence to infer statistical properties of the Mars atmospheric temperature fluctuation field. The comparison with the theory is made by simplifying assumptions that do not include wind fluctuations and diffraction effects. Two Earth years (about one Martian year) of observations acquired during the maximum convective period (10:00–14:00 Mars local time) show a good agreement between the dataset and the formalism: the travel time variance diverges from the linear Chernov solution exactly where the density of occurrence of the first caustic reaches its maximum. Moreover, on average, waves travel faster than the mean speed of sound due to a fast path effect, which is also observed on Earth. To account for the distribution of turbulent eddies, several power spectra are tested and the best match to observation is obtained with a generalized von Karman spectrum with a shallower slope than the Kolmogorov cascade, φ(k)∝(1 + k 2 L 2 ) -4/3 . It is associated with an outer scale of turbulence, L, of 11 cm at 2 m above the surface and a standard deviation of 6 K over 9 s for the temperature. These near-surface atmospheric properties are consistent with a weak to moderate wave scattering regime around noon with little saturation. Overall, this study presents an innovative and promising methodology to probe the near-surface atmospheric turbulence on Mars.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Measurements of sound propagation in Mars' lower atmosphere

Acoustics has become extraterrestrial and Mars provides a new natural laboratory for testing sound propagation models compared to those ones on Earth. Owing to the unique combination of a microphone and two sound sources, the Ingenuity helicopter and the SuperCam laser-induced sparks, the Mars 2020 Perseverance rover payload enables the in situ characterization of unique sound propagation properties of the low-pressure CO 2 -dominated Mars atmosphere. In this study, we show that atmospheric turbulence is responsible for a large variability in the sound amplitudes from laser-induced sparks. This variability follows the diurnal pattern of turbulence. In addition, acoustic measurements acquired over one Martian year reveal a variation of the sound intensity by a factor of 1.8 from a constant source due to the seasonal cycle of pressure and temperature that significantly modifies the acoustic impedance and shock-wave formation. Finally, we show that the evolution of the Ingenuity tones and laser spark amplitudes with distance is consistent with one of the existing sound absorption models, which is a key parameter for numerical simulations applied to geophysical experiments on CO 2 -rich atmospheres. Overall, these results demonstrate the potential of sound propagation to interrogate the Mars environment and will therefore help in the design of future acoustic-based experiments for Mars or other planetary atmospheres such as Venus and Titan.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Boron adsorption in clay minerals: Implications for martian groundwater chemistry and boron on Mars

Boron has been detected on Mars in calcium-sulfate veins found within clay mineral rich rocks on Mars by the Mars Science Laboratory (MSL) Curiosity rover using Laser Induced Breakdown Spectroscopy (LIBS) analysis. Borates play a vital role in stabilizing ribose on Earth and has been suggested as a key requirement for life. Borate ions readily adsorb to phyllosilicate clay minerals. The discovery of boron on Mars in proximity to phyllosilicate-bearing bedrock may have strong implications for potential past prebiotic conditions on Mars. In this study we generated a suite of clay minerals with adsorbed borate, including both typical terrestrial clay minerals (montmorillonite) and Mars-analog clay minerals (nontronite, saponite, griffithite), to understand controls on borate adsorption and to analyze with LIBS to compare with MSL data. Clay minerals were subjected to mineralogical and chemical analysis before and after adsorption. Adsorption analysis revealed that the Mars analog clay minerals adsorbed less boron than terrestrial counterparts, but within comparable amounts to those detected on Mars and in meteorites. Post-adsorption analysis by X-ray diffraction (XRD) revealed slight changes in the interlayer spacing of many of the clay minerals. Based on the adsorption analysis of the Mars-analog clay minerals, phyllosilicate-bearing bedrock in Gale crater may contain up to 90-110 ppm B. A series of borate-enriched samples were created for analysis of LIBS spectra from ChemCam on the Curiosity rover and SuperCam on the Perseverance Rover. Finally, the results of this study may provide insight into martian groundwater geochemistry processes and the mobility of a key molecule connected with life.

58 GEOSCIENCES↗
DOE OSTI2023

Depth profiling and standardization from the back side of a sample for accurate analyses: Emphasis on quantifying low‐fluence, shallow implants in diamond‐like carbon

Rationale Back‐side thinning of wafers is used to eliminate issues with transient sputtering when analyzing near‐surface element distributions. Precise and accurate calibrated implants are created by including a standard reference material during the implantation. Combining these methods allows accurate analysis of low‐fluence, shallow features even if matrix effects are a concern. Methods Implanted Na (<2.0 × 10 11 ions/cm 2 , peaking <50 nm) in diamond‐like carbon (DLC) film on silicon (solar wind returned by NASA's Genesis mission) was prepared for measurement as follows. Implanted surfaces of samples were epoxied to wafers and back‐side‐thinned using physical or chemical methods. Thinned samples were then implanted with reference ions for accurate quantification of the solar wind implant. Analyses used a CAMECA IMS 7f‐GEO SIMS in depth‐profiling mode. Results Back‐side‐implanted reference ions reduced the need to change sample mounts or stage position and could be spatially separated from the solar wind implant even when measuring monoisotopic ions. Matrix effects in DLC were mitigated and the need to find an identical piece of DLC for a reference implant was eliminated. Accuracy was only limited by the back‐side technique itself. Conclusions Combining back‐side depth profiling with back‐side‐implanted internal standards aides quantification of shallow mono‐ and polyisotopic implants. This technique helps mitigate matrix effects and keeps measurement conditions consistent. Depth profile acquisition times are longer, but if sample matrices are homogeneous, procedural changes can decrease measurement times.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

On an Extensive Late Hydrologic Event in Gale Crater as Indicated by Water‐Rich Fracture Halos

Abstract We analyze spatially pervasive, light‐toned “halos” associated with fractures in a sedimentary unit (Stimson) of Gale crater, Mars, and report a similar network of halos discovered in a separate geologic group (Bradbury). Through a dedicated active neutron measurement campaign, we provide independent confirmation of the water‐rich nature of these features. Together with mineralogical and geochemical data, these features are consistent with abundant hydrated amorphous silica (opal‐A). We suggest that the mineral and amorphous assemblages are indicative of formation under low‐temperature and predominantly low‐pH conditions (passive silica enrichment) with minor contribution of silica (active silica enrichment) from adjacent units. We show that there is significant amorphous silica in the array of sedimentary rocks in Gale crater, allowing them to play a role in an active silica enrichment phase of halo formation. We suggest that the involved alteration event was short lived and our finding of vast halo networks in a distant, older unit implies a more vast network of hydrologic subsurface conduits than previously known. This relatively recent subsurface hydrologic system was present long after the transition from a warm and wet to a cold and dry Martian environment, extending the habitability conditions on Mars to an epoch that is generally considered not favorable for life on the surface. Finally, our bulk H quantification of these features, which ranges from ∼3–6 wt% H 2 O‐equivalent‐H, suggests that the amorphous material in halos hosts ample supplies of readily released water, making them a considerable resource at the otherwise dry Martian equator.

Gabriel, Travis S. J.↗
DOE OSTI2022

Askival: An altered feldspathic cumulate sample in Gale crater

Askival is a light-toned, coarsely crystalline float rock, which was identified near the base of Vera Rubin Ridge in Gale crater. We have studied Askival, principally with the ChemCam instrument but also using APXS compositional data and MAHLI images. Askival and an earlier identified sample, Bindi, represent two rare examples of feldspathic cumulate float rocks in Gale crater with >65% relict plagioclase. Bindi appears unaltered whereas Askival shows textural and compositional signatures of silicification, along with alkali remobilization and hydration. Askival likely experienced multiple stages of alteration, occurring first through acidic hydrolysis of metal cations, followed by deposition of silica and possible phyllosilicates at low T and neutral-alkaline pH. Through laser-induced breakdown spectroscopy compositional analyses and normative calculations, we suggest that an assemblage of Fe-Mg silicates including amphibole and pyroxene, Fe phases, and possibly Mg-rich phyllosilicate are present. Thermodynamic modeling of the more pristine Bindi composition predicts that amphibole and feldspar are stable within an upper crustal setting. This is consistent with the presence of amphibole in the parent igneous rocks of Askival and suggests that the paucity of amphiboles in other known Martian samples reflects the lack of representative samples of the Martian crust rather than their absence on Mars.

58 GEOSCIENCES↗
DOE OSTI2022

Acoustics Reveals Short–Term Air Temperature Fluctuations Near Mars' Surface

Acoustics is new on Mars: it allows the characterization of turbulence at smaller scales than previously possible within the lowest part of the Planetary Boundary Layer. Sound speed measurements, by the SuperCam instrument and its microphone onboard the NASA Perseverance rover, allow the retrieval of atmospheric temperatures at 0.77 m above the ground, at 3 Hz, with a ~10 ms response time that is 20–100 times shorter than for typical thermocouple sensors used on Mars. Here we report on the first measurements of the sound speed-derived temperature and its fluctuations near the surface. Data highlight large and rapid fluctuations up to ±7 K/s, whose amplitude over such a timescale has never been reported, nor predicted by atmospheric models. These fluctuations follow the daytime pattern of the turbulence and highlight occasional high amplitude events that are likely due to the conjunction of low thermal inertia and strong winds.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

From Lake to River: Documenting an Environmental Transition Across the Jura/Knockfarril Hill Members Boundary in the Glen Torridon Region of Gale Crater (Mars)

Between January 2019 and January 2021, the Mars Science Laboratory team explored the Glen Torridon (GT) region in Gale crater (Mars), known for its orbital detection of clay minerals. Mastcam, Mars Hand Lens Imager, and ChemCam data are used in an integrated sedimentological and geochemical study to characterize the Jura member of the upper Murray formation and the Knockfarril Hill member of the overlying Carolyn Shoemaker formation in northern GT. The studied strata show a progressive transition represented by interfingering beds of fine–grained, recessive mudstones of the Jura member and coarser–grained, cross–stratified sandstones attributed to the Knockfarril Hill member. Whereas the former are interpreted as lacustrine deposits, the latter are interpreted as predominantly fluvial deposits. The geochemical composition seen by the ChemCam instrument show K 2 O–rich mudstones (~1–2 wt.%) versus MgO–rich sandstones (>6 wt.%), relative to the average composition of the underlying Murray formation. We document consistent sedimentary and geochemical data sets showing that low–energy mudstones of the Jura member are associated with the K–rich endmember, and that high–energy cross–stratified sandstones of the Knockfarril Hill member are associated with the Mg–rich endmember, regardless of stratigraphic position. The Jura to Knockfarril Hill transition therefore marks a significant paleoenvironmental change, where a long–lived and comparatively quiescent lacustrine setting progressively changes into a more energetic fluvial setting, as a consequence of shoreline regression due to either increased sediment supply or lake–level drop.

58 GEOSCIENCES↗
DOE OSTI2022

Compositionally and density stratified igneous terrain in Jezero crater, Mars

Before Perseverance, Jezero crater’s floor was variably hypothesized to have a lacustrine, lava, volcanic airfall, or aeolian origin. SuperCam observations in the first 286 Mars days on Mars revealed a volcanic and intrusive terrain with compositional and density stratification. The dominant lithology along the traverse is basaltic, with plagioclase enrichment in stratigraphically higher locations. Stratigraphically lower, layered rocks are richer in normative pyroxene. The lowest observed unit has the highest inferred density and is olivine-rich with coarse (1.5 millimeters) euhedral, relatively unweathered grains, suggesting a cumulate origin. This is the first martian cumulate and shows similarities to martian meteorites, which also express olivine disequilibrium. Alteration materials including carbonates, sulfates, perchlorates, hydrated silicates, and iron oxides are pervasive but low in abundance, suggesting relatively brief lacustrine conditions. Orbital observations link the Jezero floor lithology to the broader Nili-Syrtis region, suggesting that density-driven compositional stratification is a regional characteristic.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

The dynamic atmospheric and aeolian environment of Jezero crater, Mars

Despite the importance of sand and dust to Mars geomorphology, weather, and exploration, the processes that move sand and that raise dust to maintain Mars’ ubiquitous dust haze and to produce dust storms have not been well quantified in situ, with missions lacking either the necessary sensors or a sufficiently active aeolian environment. Perseverance rover’s novel environmental sensors and Jezero crater’s dusty environment remedy this. In Perseverance’s first 216 sols, four convective vortices raised dust locally, while, on average, four passed the rover daily, over 25% of which were significantly dusty (“dust devils”). More rarely, dust lifting by nonvortex wind gusts was produced by daytime convection cells advected over the crater by strong regional daytime upslope winds, which also control aeolian surface features. One such event covered 10 times more area than the largest dust devil, suggesting that dust devils and wind gusts could raise equal amounts of dust under nonstorm conditions.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Optical calibration of the SuperCam instrument body unit spectrometers

The SuperCam remote sensing instrument on NASA’s Perseverance rover is capable of four spectroscopic techniques, remote micro-imaging, and audio recording. These analytical techniques provide details of the chemistry and mineralogy of the rocks and soils probed in the Jezero Crater on Mars. Here we present the methods used for optical calibration of the three spectrometers covering the 243–853 nm range used by three of the four spectroscopic techniques. We derive the instrument optical response, which characterizes the instrument sensitivity to incident radiation as a function of a wavelength. The instrument optical response function derived here is an essential step in the interpretation of the spectra returned by SuperCam as it converts the observed spectra, reported by the instrument as “digital counts” from an analog to digital converter, into physical values of spectral radiance.

Legett, Carey (ORCID:0000000247412841)↗
NASA NTRS2018

Incorporating AEGIS Autonomous Science into Mars Science Laboratory Rover Mission Operations

The AEGIS (Autonomous Exploration for Gathering Increased Science) intelligent targeting software system has been in use on the Mars Science Laboratory (MSL) mission since 2016. The system allows on-board autonomous selection of targets for the ChemCam remote geochemistry instrument based on analysis of images taken by the rover. This paper describes the deployment of AEGIS to MSL and the operational use of the system since rollout to science operations in May of 2016.

Deflores, Lauren↗