Engineering topics

Wieseman, Carol D.

Publications and source records attributed to Wieseman, Carol D..

47 records · Page 3

NASA NTRS1993

Experimental unsteady pressures at flutter on the Supercritical Wing Benchmark Model

This paper describes selected results from the flutter testing of the Supercritical Wing (SW) model. This model is a rigid semispan wing having a rectangular planform and a supercritical airfoil shape. The model was flutter tested in the Langley Transonic Dynamics Tunnel (TDT) as part of the Benchmark Models Program, a multi-year wind tunnel activity currently being conducted by the Structural Dynamics Division of NASA Langley Research Center. The primary objective of this program is to assist in the development and evaluation of aeroelastic computational fluid dynamics codes. The SW is the second of a series of three similar models which are designed to be flutter tested in the TDT on a flexible mount known as the Pitch and Plunge Apparatus. Data sets acquired with these models, including simultaneous unsteady surface pressures and model response data, are meant to be used for correlation with analytical codes. Presented in this report are experimental flutter boundaries and corresponding steady and unsteady pressure distribution data acquired over two model chords located at the 60 and 95 percent span stations.

Dansberry, Bryan E.↗

NASA NTRS1992

Multiple-function multi-input/multi-output digital control and on-line analysis

The design and capabilities of two digital controller systems for aeroelastic wind-tunnel models are described. The first allowed control of flutter while performing roll maneuvers with wing load control as well as coordinating the acquisition, storage, and transfer of data for on-line analysis. This system, which employs several digital signal multi-processor (DSP) boards programmed in high-level software languages, is housed in a SUN Workstation environment. A second DCS provides a measure of wind-tunnel safety by functioning as a trip system during testing in the case of high model dynamic response or in case the first DCS fails. The second DCS uses National Instruments LabVIEW Software and Hardware within a Macintosh environment.

Hoadley, Sherwood T.↗

NASA NTRS1992

On-line analysis capabilities developed to support the AFW wind-tunnel tests

A variety of on-line analysis tools were developed to support two active flexible wing (AFW) wind-tunnel tests. These tools were developed to verify control law execution, to satisfy analysis requirements of the control law designers, to provide measures of system stability in a real-time environment, and to provide project managers with a quantitative measure of controller performance. Descriptions and purposes of the developed capabilities are presented along with examples. Procedures for saving and transferring data for near real-time analysis, and descriptions of the corresponding data interface programs are also presented. The on-line analysis tools worked well before, during, and after the wind tunnel test and proved to be a vital and important part of the entire test effort.

Wieseman, Carol D.↗

NASA NTRS1992

Time simulation of flutter with large stiffness changes

Time simulation of flutter, involving large local structural changes, is formulated with a state-space model that is based on a relatively small number of generalized coordinates. Free-free vibration modes are first calculated for a nominal finite-element model with relatively large fictitious masses located at the area of structural changes. A low-frequency subset of these modes is then transformed into a set of structural modal coordinates with which the entire simulation is performed. These generalized coordinates and the associated oscillatory aerodynamic force coefficient matrices are used to construct an efficient time-domain, state-space model for a basic aeroelastic case. The time simulation can then be performed by simply changing the mass, stiffness, and damping coupling terms when structural changes occur. It is shown that the size of the aeroelastic model required for time simulation with large structural changes at a few apriori known locations is similar to that required for direct analysis of a single structural case. The method is applied to the simulation of an aeroelastic wind-tunnel model. The diverging oscillations are followed by the activation of a tip-ballast decoupling mechanism that stabilizes the system but may cause significant transient overshoots.

Karpel, Mordechay↗

NASA NTRS1992

On-line analysis capabilities developed to support the AFW wind-tunnel tests

A variety of on-line analysis tools were developed to support two Active Flexible Wing wind-tunnel tests. These tools were developed to verify control law execution, to satisfy analysis requirements of the control law designers, to provide measures of system stability in a real-time environment, and to provide project managers with a quantitative measure of controller performance. Description and purposes of capabilities which were developed are presented in this paper along with examples. Procedures for saving and transferring data for near real-time analysis, and descriptions of the corresponding data interface programs are also presented. The on-line analysis tools worked well before, during, and after the wind-tunnel tests and proved to be a vital and important part of the entire test effort.

Wieseman, Carol D.↗

NASA NTRS1991

A status report on a model for Benchmark active controls testing

This 'work-in-progress' paper presents a status report on an active controls flutter model which is currently in the design and fabrication phase. This model is a part of the Benchmark Models Program (BMP). The BMP is a NASA LaRC program that includes a series of models which will be used to study different aeroelastic phenomena and to validate aeroelastic methods. The objective of Benchmark Active Controls testing is to validate active control design tools. Flutter testing will be conducted with a pressure-instrumented rigid model attached to a flexible pitch and plunge mount system. Unsteady pressure distributions and transonic flutter boundaries will be measured with and without active control system engaged.

Durham, Michael H.↗

NASA NTRS1990

Development and testing of methodology for evaluating the performance of multi-input/multi-output digital control systems

A Controller Performance Evaluation (CPE) methodology for multi-input/multi-output digital control systems was developed and tested on an aeroelastic wind-tunnel model. Modern signal processing methods were used to implement control laws and to acquire time domain data of the whole system (controller and plant) from which appropriate transfer matrices of the control system could be generated. Matrix computational procedures were used to calculate singular values of return-difference matrices at the plant input and output points to evaluate the performance of the control system. The CPE procedures effectively identified potentially destabilizing controllers and confirmed the satisfactory performance of stabilizing ones.

Pototzky, Anthony S.↗

NASA NTRS1989

Aeroelastic modeling for the FIT (Functional Integration Technology) team F/A-18 simulation

As part of Langley Research Center's commitment to developing multidisciplinary integration methods to improve aerospace systems, the Functional Integration Technology (FIT) team was established to perform dynamics integration research using an existing aircraft configuration, the F/A-18. An essential part of this effort has been the development of a comprehensive simulation modeling capability that includes structural, control, and propulsion dynamics as well as steady and unsteady aerodynamics. The structural and unsteady aerodynamics contributions come from an aeroelastic mode. Some details of the aeroelastic modeling done for the Functional Integration Technology (FIT) team research are presented. Particular attention is given to work done in the area of correction factors to unsteady aerodynamics data.

Zeiler, Thomas A.↗

NASA NTRS1989

Aeroelastic modeling for the FIT team F/A-18 simulation

Some details of the aeroelastic modeling of the F/A-18 aircraft done for the Functional Integration Technology (FIT) team's research in integrated dynamics modeling and how these are combined with the FIT team's integrated dynamics model are described. Also described are mean axis corrections to elastic modes, the addition of nonlinear inertial coupling terms into the equations of motion, and the calculation of internal loads time histories using the integrated dynamics model in a batch simulation program. A video tape made of a loads time history animation was included as a part of the oral presentation. Also discussed is work done in one of the areas of unsteady aerodynamic modeling identified as needing improvement, specifically, in correction factor methodologies for improving the accuracy of stability derivatives calculated with a doublet lattice code.

Zeiler, Thomas A.↗

NASA NTRS1988

Methodology for matching experimental and computational aerodynamic data

Correction factor methodologies have been developed which use steady experimental or analytical pressure or force data to correct steady and unsteady aerodynamic calculations. Three methods of calculating correction factors have been developed to match steady surface pressure distributions, to match airfoil section forces and moments. Data for a rectangular supercritical wing that was previously tested in the NASA Langley Research Center Transonic Dynamics Tunnel have been used to determine correction factors to match surface pressure distributions for a range of Mach numbers.

Wieseman, Carol D.↗

NASA NTRS1988

Methodology for matching experimental and analytical aerodynamic data

Correction factor methodologies have been developed which use steady experimental or analytical pressure or force data to correct steady and unsteady aerodynamic calculations. Three methods of calculating correction factors have been developed to match steady surface pressure distributions, to match airfoil section forces and moments, and to match total forces and moments. Data for a rectangular supercritical wing that was previously tested in the NASA Langley Research Center Transonic Dynamics Tunnel have been used to determine correction factors to match surface pressure distributions for a range of Mach numbers.

Wieseman, Carol D.↗