Engineering topics

Wiker, Steven F.

Publications and source records attributed to Wiker, Steven F..

6 records

NASA NTRS1992

Grasp force control in telemanipulation

This paper presents two experiments which focus upon the issue of grasp force control in telemanipulation. The first experiment examines the ability to control and stabilize master-controller grasp force during a 30-s compensatory tracking task under different levels of master controller digit mass, friction, and backlash. The second experiment explores the potential for substituting tactile feedback in lieu of direct force-feedback to gage and control remote grasp force. Results show that subjects were better able to control force when mass and friction levels were increased. Even when perceptual gains between tactile and direct force feedback displays were matched, force reflection produced better grasp control. The lack of backlash effects and improvements in performance with direct force reflection in comparison to tactile feedback are attributable to reflexive short-loop adjustment of grasp tension afforded by the muscle's length-tension control system. The criterion of acceptable operator performance, dependent upon both the quality of the transmission of control commands and feedback, and the response of the remote device, is discussed.

Wiker, Steven F.↗

NASA NTRS1992

Importance of numerosity and distribution of articulations within the digits, wrists, and arms of telemanipulators confronted with dextrous assembly tasks

This study was conducted to evaluate the impact of successive exclusion of degrees-of-freedom within digits (thumb and index finger) and wrist when performing tasks demanding varying degrees of end effector kinematic complexity. The analysis was performed by successive constraining articulations in the fingers (thumb and index) and wrists or human subjects via splints, and then timing performance of part movement, positioning, and assembly operations requiring different levels of kinematic freedom. Analysis of performance times showed that transferring degrees-of-freedom, or articulations, from the digits to the wrist and arm had little or no material affect upon manipulation performance times if wrist and arm kinematics were unrestricted. If wrist and arm kinematics are not constrained and are of high-quality, our findings show that transferring kinematic freedom from the digits to the wrist and arms or remote end effectors offers limited or no consequence in terms of remote assembly operations. The importance of such findings, in terms of development and implementation of commercially attractive telemanipulators, is discussed.

Wiker, Steven F.↗

NASA NTRS1991

Impact of inertia, friction, and backlash upon force control in telemanipulation

The mechanical behavior of master controllers of telemanipulators has been a concern of both designers and implementors of telerobotic systems. In general, the literature recommends that telemanipulator systems be constructed that minimize inertia, friction, and backlash in an effort to improve telemanipulative performance. For the most part, these recommendations are founded upon theoretical analysis or simply intuition. Although these recommendations are not challenged on their merit, the material results are measured of building and fielding telemanipulators that possess less than ideal mechanical behaviors. Experiments are described in which forces in a mechanical system with human input are evaluated as a function of mechanical characteristics such as inertia, friction, and backlash. Results indicate that the ability of the human to maintain gripping forces was relatively unaffected by dynamic characteristics in the range studied, suggesting that telemanipulator design in this range should be based on task level force control requirements rather than human factors.

Duffie, Neil A.↗

NASA NTRS1991

Comparison of force and tactile feedback for grasp force control in telemanipulation

The comparative efficacy of using direct force feedback or a simple vibrotactile display to convey changes in the intensity of remote grasp force relayed from a robotic end effector is examined. The findings show that a simple vibrotactile cue, in the absence of direct force feedback, is effective in signaling abrupt changes in remote grasp force regardless of magnitude, and when changes in force are not too slow or protracted in nature (i.e., ramp time less than 2 s). In cases where the operator must dynamically tract and respond to slow but large variations in grasp force, the comparatively crude vibrotactile display would prove helpful; but would not be as effective as that of a direct contact force display. Immediate applications and utility of current generation and near-term prototype tactile displays are discussed.

Wiker, Steven F.↗

NASA NTRS1990

Test bed experiments for various telerobotic system characteristics and configurations

Dexterous manipulation and grasping in telerobotic systems depends on the integration of high-performance sensors, displays, actuators and controls into systems in which careful consideration has been given to human perception and tolerance. Research underway at the Wisconsin Center for Space Automation and Robotics (WCSAR) has the objective of enhancing the performance of these systems and their components, and quantifying the effects of the many electrical, mechanical, control, and human factors that affect their performance. This will lead to a fundamental understanding of performance issues which will in turn allow designers to evaluate sensor, actuator, display, and control technologies with respect to generic measures of dexterous performance. As part of this effort, an experimental test bed was developed which has telerobotic components with exceptionally high fidelity in master/slave operation. A Telerobotic Performance Analysis System has also been developed which allows performance to be determined for various system configurations and electro-mechanical characteristics. Both this performance analysis system and test bed experiments are described.

Duffie, Neil A.↗

NASA NTRS1989

Teleoperator comfort and psychometric stability: Criteria for limiting master-controller forces of operation and feedback during telemanipulation

The following question is addressed: How much force should operators exert, or experience, when operating a telemanipulator master-controller for sustained periods without encountering significant fatigue and discomfort, and without loss of stability in psychometric perception of force. The need to minimize exertion demands to avoid fatigue is diametrically opposed by the need to present a wide range of force stimuli to enhance perception of applied or reflected forces. For 104 minutes subjects repetitiously performed a series of 15 s isometric pinch grasps; controlled at 5, 15, and 25 percent of their maximum voluntary strength. Cyclic pinch grasps were separated by rest intervals of 7.5 and 15 s. Upon completion of every 10 minute period, subjects interrupted grasping activities to gage the intensity of fatigue and discomfort in the hand and forearm using a cross-modal matching technique. A series of psychometric tests were then conducted to determine accuracy and stability in the subject's perception of force experienced. Results showed that onset of sensations of discomfort and fatigue were dependent upon the magnitude of grasp force, work/rest ratio, and progression of task. Declines in force magnitude estimation slopes, indicating a reduction in force perception sensitivity, occurred with increased grasp force when work/rest ratios were greater than 1.0. Specific recommendations for avoiding discomfort and shifts in force perception, by limiting pinch grasp force required for master-controller operation and range of force reflection or work/rest ratios, are provided.

Wiker, Steven F.↗