Search NASA⌕ Search

Engineering topics

William P Winfree

Publications and source records attributed to William P Winfree.

12 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Synchronized Electronic Shutter System and Method for Thermal Nondestructive Evaluation

The invention is a synchronized electronic shutter system (SESS) and method for same side and through transmission thermal analysis and inspection of a material for finding defects, corrosion, disbond defects, integrity of a weld and determination of paint thickness. The system comprises an infrared detector that acquires background images of the sample. A shutter then covers the detector and lamps rapidly heat the sample above ambient temperature. Shutters cover all lamps at the same time the shutter over the infrared detector is opened. The infrared detector acquires a series of temperature images over time radiated from the sample a s the sample cools down. After collecting a series of temperature images taken by the SESS, a processed image is developed using one of the group comprising time derivative calculation, temperature normalization data reduction routine, thermal diffusivity curve fitting and averaging the series of temperature images.

Joseph N Zalameda↗
NASA NTRS1991

Thermal QNDE detection of airframe disbonds

Thermographic characterization of aircraft bonded lap joints offers a quick noncontacting technique to acquire information for structural integrity assessment. This paper discusses recent research to optimize the technique and determine the limits of its applicability. The temperature of the outer surface of the lap joint is increased by the application of heat flux from either flash or quartz lamp heaters. The time dependence of the surface temperature of the lap joint is imaged radiometrically. Measurements are presented for a range of specimens, ranging from samples fabricated with well characterized disbonds to actual aircraft. A technique for processing these images to enhance the contrast between bonded and disbonded regions of the lap joint is presented. Numerical models of the technique simulate the procedure. These simulations provide a cost efficient method for optimizing the technique by varying parameters such as the time for application of heat. These simulations facilitate the definition of parameters difficult to determine experimentally, such as the minimum air gap required for a disbond to be detected. Good agreement between measurements and these simulations is found.

Aging Aircraft↗
NASA NTRSDate not supplied

Nondestructive Evaluation for the Space Shuttle's Wing Leading Edge

The loss of the Space Shuttle Columbia highlighted concerns about the integrity of the Shuttle's thermal protection system, which includes Reinforced Carbon-Carbon (RCC) on the leading edge. This led NASA to investigate nondestructive evaluation (NDE) methods for certifying the integrity of the Shuttle's wing leading edge. That investigation was performed simultaneously with a large study conducted to understand the impact damage caused by errant debris. Among the many advanced NDE methods investigated for applicability to the RCC material, advanced digital radiography, high resolution computed tomography, thermography, ultrasound, acoustic emission and eddy current systems have demonstrated the maturity and success for application to the Shuttle RCC panels. For the purposes of evaluating the RCC panels while they are installed on the orbiters, thermographic detection incorporating principal component analysis (PCA) and eddy current array scanning systems demonstrated the ability to measure the RCC panels from one side only and to detect several flaw types of concern. These systems were field tested at Kennedy Space Center (KSC) and at several locations where impact testing was being conducted. Another advanced method that NASA has been investigating is an automated acoustic based detection system. Such a system would be based in part on methods developed over the years for acoustic emission testing. Impact sensing has been demonstrated through numerous impact tests on both reinforced carbon-carbon (RCC) leading edge materials as well as Shuttle tile materials on representative aluminum wing structures. A variety of impact materials and conditions have been evaluated including foam, ice, and ablator materials at ascent velocities as well as simulated hypervelocity micrometeoroid and orbital debris impacts. These tests have successfully demonstrated the capability to detect and localize impact events on Shuttle's wing structures. A first generation impact sensing system has been designed for the next Shuttle flight and is undergoing final evaluation for deployment on the Shuttle's first return to flight. This system will employ wireless accelerometer sensors that were qualified for other applications on previous Shuttle flights. These sensors will be deployed on the wing's leading edge to detect impacts on the RCC leading edge panels. The application of these methods will help to insure the continued integrity of the Shuttle wing's leading edge system as the Shuttle flights resume and until their retirement.

Eric I Madaras↗
NASA NTRSDate not supplied

Parallelized Quadrupole Simulations of Thermographic Responses of Composites

Thermography has been shown to be a viable technique for inspection of composites. Model inversion of the thermography data requires a fast method for performing the forward problem. Viable numerical methods for the thermal response forward problem are finite element, finite difference and the quadrupole method. Normally both the finite element and finite difference methods solve for the thermal response in the time domain which limits one’s ability to increase the speed of the simulation by parallelization. In contrast, the quadrupole method solves for the Laplace transform of the thermal response. One of the features of the Laplace transform methodology is the solution at any discrete time is independent of the solution at all other times. Therefore, it is easy to separate into a set of independent calculations with each of the times of interest being performed in parallel. Additionally, the numeric inversion of the Laplace transform typically involves numerically solving for the Laplace transform at multiple Laplace frequencies. Each of those solutions are also independent of solutions at other frequencies and can be calculated in parallel. By parallelization of this method, it is possible to perform the simulations of three-dimensional configurations in seconds. When the input stimulus for thermal response is a delta function heat flux (a reasonable approximation for flash heating), the thermal response is smooth. For this case, it is possible to accurately estimate the thermal response at any time within a given time interval from a set of simulations separated by exponentially increasing time steps. From these simulations, it is possible to accurately interpolate to find the response at intermediate times by a spline interpolation of the logarithm of time versus logarithm of temperature. The thermal response with exponential time stepping is shown to produce values for the thermal response which are within 1% of values within the time interval. The simulations are compared to finite element simulations of the same inspection configurations. The simulations are also compared to the thermographic measurements on composites where shape and depth of the delaminations are obtained from other inspection methods.

Thermography↗
NASA NTRSDate not supplied

Delamination Depth Imaging for Quasi-Static and Fatigue Load Testing Using Passive Thermography

Passive thermography is used to monitor small increases in temperature resulting from delamination damage formation in composite hat-stiffened panels during both quasi-static and fatigue loading. It has been observed that rapid damage formation produces heating. This is composed of two heat generation components. The first component is an instantaneous response due to an irreversible thermoelastic strain release. The second component is mechanical heating, at the interface of failure, due to fracture damage. This produces a transient rise in temperature as the heat diffuses to the surface. The first component defines the thermal start time for the transient response. A one-dimensional thermal model is fitted to the data pixel by pixel, to produce imagery of the damage depth. The results are compared to ultrasonic and X-ray CT data.

Passive thermography↗
NASA NTRSDate not supplied

Quadrupole Simulations of Thermographic Responses of Composites

Thermography has been shown to be a viable technique for inspection of composites. The quadrupole method has been shown as a viable technique for rapidedly simulating the thermal repsonse of layered systems. Often, the effort has focused on a one-dimentional models, in particular for improved analysis of thermal data. For composites, the in-plane heat diffusion often significantly impacts the thermal response of defects of interest, therefore three-dimensional simulations are desirable. This paper discusses the extension of the quadrupole methodology to perform simulations of thermographic responses in three-dimensional configuration. This enables the more realistic simulations of the thermal response of delaminiations in composites. The simulations are compared to finite element simulations of the same inspection configurations. The simulations are also compared to the thermographic measurements on composites where shape and depth of the delaminations are known obtained from other sources.

Thermography↗
NASA NTRSDate not supplied

Simulation of Thermographic Responses of Delaminations in Composites with Quadrupole Method

Thermography has been shown to be a viable technique for inspection of composites. The quadrupole method is a valuable technique for rapidly simulating the thermal response of layered systems. Often, the effort has focused on a one-dimensional model, in particular for improved analysis of thermal data. For composites, the in-plane heat diffusion often significantly impacts the thermal response of defects of interest, therefore three-dimensional simulations are desirable. This paper discusses the extension of the quadrupole methodology to perform simulations of thermographic responses in three-dimensional configurations. This enables the more realistic simulations of the thermal response of delaminations in composites. The simulations are compared to finite element simulations of the same inspection configurations.

Thermography↗
NASA NTRSDate not supplied

Realistic Thermographic Simulation of Impact Damage with Quadrupole Method

Flash thermography has been shown to be an effective method for detection of delaminations in carbon fiber reinforced polymer (CFRP) composite structures. Improved understanding of the limitations of the technique can be obtained by simulating the inspection process. Time domain finite difference and finite element methods are well suited for such simulations but can be computationally intensive. An alternate method is to solve the Laplace transform of the heat equation, then invert the Laplace transform to produce a time domain response. Often this is referred to as the thermal quadrupole method and is well suited for simulating flash thermography. The quadrupole method has been used extensively for simulating one-dimensional heat flow in multilayer systems with contact resistances at the interfaces. It is also applicable for three dimensional configurations, in particular for simulation of changes in thermographic response due to delaminations in composites. This presentation discusses three-dimensional simulations with realistic shapes and contact resistances at the interfaces between layers. The results of these simulations are compared to thermography measurements on composites specimens with impact induced delaminations.

thermography↗
NASA NTRSDate not supplied

Parallelized Quadrupole Simulations of Thermographic Responses of Composites

Thermography has been shown to be a viable technique for inspection of composites. Model inversion of the thermography data requires a fast method for performing the forward problem. Viable numerical methods for the thermal response forward problem are finite element, finite difference and the quadrupole method. Normally both the finite element and finite difference methods solve for the thermal response in the time domain which limits one’s ability to increase the speed of the simulation by parallelization. In contrast, the quadrupole method solves for the Laplace transform of the thermal response. One of the features of the Laplace transform methodology is the solution at any discrete time is independent of the solution at all other times. Therefore, it is easy to separate into a set of independent calculations with each of the times of interest being performed in parallel. Additionally, the numeric inversion of the Laplace transform typically involves numerically solving for the Laplace transform at multiple Laplace frequencies. Each of those solutions are also independent of solutions at other frequencies and can be calculated in parallel. By parallelization of this method, it is possible to perform the simulations of three-dimensional configurations in seconds. When the input stimulus for thermal response is a delta function heat flux (a reasonable approximation for flash heating), the thermal response is smooth. For this case, it is possible to accurately estimate the thermal response at any time within a given time interval from a set of simulations separated by exponentially increasing time steps. From these simulations, it is possible to accurately interpolate to find the response at intermediate times by a spline interpolation of the logarithm of time versus logarithm of temperature. The thermal response with exponential time stepping is shown to produce values for the thermal response which are within 1% of values within the time interval. The simulations are compared to finite element simulations of the same inspection configurations. The simulations are also compared to the thermographic measurements on composites where shape and depth of the delaminations are obtained from other inspection methods.

Thermography↗
NASA NTRSDate not supplied

Realistic Thermographic Simulation of Impact Damage with Quadrupole Method

Flash thermography has been shown to be an effective method for detection of delaminations in carbon fiber reinforced polymer (CFRP) composite structures. Improved understanding of thelimitations of the technique can be obtained by simulating the inspection process. Time domainfinite difference and finite element methods are well suited for such simulations but can be computationally intensive. An alternate method is to solve the Laplace transform of the heat equation, then invert the Laplace transform to produce a time domain response. Often this is referred to as the thermal quadrupole method and is well suited for simulating flash thermography. The quadrupole method has been used extensively for simulating one-dimensional heat flow in multilayer systems with contact resistances at the interfaces. It is also applicable for three dimensional configurations, in particular for simulation of changes in thermographic response due to delaminations in composites. This presentation discusses three-dimensional simulations with realistic shapes and contact resistances at the interfaces between layers. The results of these simulations are compared to thermography measurements on composites specimens with impact induced delaminations.

Thermography↗