Search NASA⌕ Search

Engineering topics

Williams, Hunter

Publications and source records attributed to Williams, Hunter.

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

Development of a CubeSat-Scale Green Monopropellant Propulsion System for NASA's Lunar Flashlight Mission

NASA's Lunar Flashlight is a low-cost 6U CubeSat whose mission is to search for ice and mineral deposits inside of the scattered craters at Moon's southern pole. To conduct its primary science mission, Lunar Flashlight must be placed in a stable lunar polar orbit which requires the utilization of an on-board propulsion system. However, to this date, most CubeSats have been propelled by cold-gas or electric propulsion systems that have proven to scale well but lack sufficient impulse to conduct large $\Delta V$ maneuvers such as orbit insertions. To this end, the Lunar Flashlight mission has chosen to utilize a custom-designed green monopropellant propulsion system developed by the Georgia Institute of Technology under the leadership of NASA's Marshall Space Flight Center and support from the Jet Propulsion Laboratory. The developed system is capable of providing more than the required propulsive capability for full mission success while fitting inside of a 2.5U volume and weighing less than six kilograms. The system utilizes the Advanced Space Craft Energetic Non Toxic (ASCENT) green monopropellant that provides higher specific impulse compared to traditional hydrazine while also being safer to handle. If successful, the presented propulsion system will enable Lunar Flashlight to be the first CubeSat to reach the Moon, the first to conduct an orbit insertion, and will be the first CubeSat demonstration of the ASCENT propellant.

Kowalkowski, Matthew↗
NASA NTRS2019

Assessment of MON-25/MMH Propellant System for Deep-Space Engines

Hypergolic propellant system of oxidizer MON-25 and fuel MMH has been considered in propulsion trade studies for NASA science mission concepts. A propulsion system using this bi-propellant combination will be capable of operating at a lower temperature as compared to traditional MON-3/MMH for heater power reduction. Operation robustness can also be realized since such a propellant system is utilized under a wide range of temperatures. Propulsion system designs and engine test programs for MON-25/MMH have been carried out since 2008. Several engine development programs have been conducted. The thrust classes of 22-Newton [5-lb(sub f)] and 445-Newton [100-lb(sub f)] were tested with the capability of a pulse mode operation for a wide range of duty cycles. Additional engine development tests are followed. Outcomes of the development efforts suggest that there is a balance of mission benefits and potential engine design and operation challenges, although the propellants can handle a low temperature. This paper will report an assessment of using the MON-25/MMH system for deep- space application.

Trinh, Huu P.↗
NASA NTRS2015

NASA Propulsion Concept Studies and Risk Reduction Activities for Resource Prospector Lander

The Resource Prospector mission is to investigate the Moon's polar regions in search of volatiles. The government-version lander concept for the mission is composed of a braking stage and a liquid-propulsion lander stage. A propulsion trade study concluded with a solid rocket motor for the braking stage while using the 4th-stage Peacekeeper (PK) propulsion components for the lander stage. The mechanical design of the liquid propulsion system was conducted in concert with the lander structure design. A propulsion cold-flow test article was fabricated and integrated into a lander development structure, and a series of cold flow tests were conducted to characterize the fluid transient behavior and to collect data for validating analytical models. In parallel, RS-34 PK thrusters to be used on the lander stage were hot-fire tested in vacuum conditions as part of risk reduction activities.

Trinh, Huu P.↗
NASA NTRS2015

NASA Propulsion Concept Studies and Risk Reduction Activities for Resource Prospector Lander

The trade study has led to the selection of propulsion concept with the lowest cost and net lowest risk -Government-owned, flight qualified components -Meet mission requirements although the configuration is not optimized. Risk reduction activities have provided an opportunity -Implement design improvements while development with the early-test approach. -Gain knowledge on the operation and identify operation limit -Data to anchor analytical models for future flight designs; The propulsion system cold flow tests series have provided valuable data for future design. -The pressure surge from the system priming and waterhammer within component operation limits. -Enable to optimize the ullage volume to reduce the propellant tank mass; RS-34 hot fire tests have successfully demonstrated of using the engines for the RP mission -No degradation of performance due to extended storage life of the hardware. -Enable to operate the engine for RP flight mission scenarios, outside of the qualification regime. -Provide extended data for the thermal and GNC designs. Significant progress has been made on NASA propulsion concept design and risk reductions for Resource Prospector lander.

Trinh, Huu P.↗
NASA NTRS2015

Resource Prospector Propulsion System Cold Flow Testing

Resource Prospector (RP) is a NASA mission being led by NASA Ames Research Center with current plans to deliver a scientific payload package aboard a rover to the lunar surface. As part of an early risk reduction activity, Marshall Space Flight Center (MSFC) and Johnson Space Flight Center (JSC) have jointly developed a government-version concept of a lunar lander for the mission. The spacecraft consists of two parts, the lander and the rover which carries the scientific instruments. The lander holds the rover during launch, cruise, and landing on the surface. Following terminal descent and landing the lander portion of the spacecraft become dormant after the rover embarks on the science mission. The lander will be equipped with a propulsion system for lunar descent and landing, as well as trajectory correction and attitude control maneuvers during transit to the moon. Hypergolic propellants monomethyl hydrazine and nitrogen tetroxide will be used to fuel sixteen 70-lbf descent thrusters and twelve 5-lbf attitude control thrusters. A total of four metal-diaphragm tanks, two per propellant, will be used along with a high-pressure composite-overwrapped pressure vessel for the helium pressurant gas. Many of the major propulsion system components are heritage missile hardware obtained by NASA from the Air Force. In parallel with the flight system design activities, a simulated propulsion system based on flight drawings was built for conducting a series of water flow tests to characterize the transient fluid flow of the propulsion system feed lines and to verify the critical operation modes such as system priming, waterhammer, and crucial mission duty cycles. The primary objective of the cold flow testing was to simulate the RP propulsion system fluid flow operation through water flow testing and to obtain data for anchoring analytical models. The models will be used to predict the transient and steady state flow behaviors in the actual flight operations. All design and build efforts, including the analytical modeling, have been performed. The cold flow testing of the propulsion system was set up and conducted at a NASA MSFC test facility. All testing was completed in the summer of 2014, and this paper documents the results of that testing and the associated fluid system modeling efforts.

Williams, Hunter↗
NASA NTRS2014

Resource Prospector Propulsion Cold Flow Test

For the past year, NASA Marshall Space Flight Center and Johnson Space Center have been working on a government version of a lunar lander design for the Resource Prospector Mission. A propulsion cold flow test system, representing an early flight design of the propulsion system, has been fabricated. The primary objective of the cold flow test is to simulate the Resource Prospector propulsion system operation through water flow testing and obtain data for anchoring analytical models. This effort will also provide an opportunity to develop a propulsion system mockup to examine hardware integration to a flight structure. This paper will report the work progress of the propulsion cold flow test system development and test preparation. At the time this paper is written, the initial waterhammer testing is underway. The initial assessment of the test data suggests that the results are as expected and have a similar trend with the pretest prediction. The test results will be reported in a future conference.

Williams, Hunter↗
NASA NTRS2010

NASA Ares I Launch Vehicle Upper Stage Reaction Control System (ReCS) Cold Flow Development Test Overview

NASA s Ares I launch vehicle, consisting of a five segment solid rocket booster first stage and a liquid bi-propellant J2-X engine Upper Stage, is the vehicle that s been chosen to launch the Orion Crew Module, which will return humans to the Moon, Mars, and beyond. After First Stage booster separation, the Reaction Control System (ReCS), a monopropellant hydrazine system, will provide the Upper Stage element with three degrees of freedom control as needed. This paper provides an overview of the system level development testing that has taken place on the Ares I launch vehicle Upper Stage ReCS. The ReCS System Development Test Article (SDTA) was built as a flight representative water flow test article whose primary test objective was to obtain fluid system performance data to evaluate the integrate system performance characteristics and verify analytical models. Water is the industry standard for cold flow testing of hydrazine systems, because the densities are very close and the speeds of sound are well characterized. The completion of this development level test program was considered necessary to support the ReCS Critical Design Review. This paper will address the design approach taken in building the test article, the objectives of the test program, types of testing completed, general results, the ability of the program to meet the test objectives, and lessons learned

Dervan, Melanie↗