Engineering topics

Williams, J. H., Jr.

Publications and source records attributed to Williams, J. H., Jr..

At least 19 records

NASA NTRS1986

Ultrasonic determination of the elastic constants of the stiffness matrix for unidirectional fiberglass epoxy composites

The elastic constants of a fiberglass epoxy unidirectional composite are determined by measuring the phase velocities of longitudinal and shear stress waves via the through transmission ultrasonic technique. The waves introduced into the composite specimens were generated by piezoceramic transducers. Geometric lengths and the times required to travel those lengths were used to calculate the phase velocities. The model of the transversely isotropic medium was adopted to relate the velocities and elastic constants.

Marques, E. R. C.↗

NASA NTRS1986

Parameterized materials and dynamic response characterizations in unidirectional composites

The values of phase velocities of ultrasonic waves in transversely isotropic media are presented in terms of the fiber volume fraction of a unidirectional fiberglass epoxy composite with constant matrix properties and the ratio between extensional moduli in the longitudinal and transverse directions of the composite when the properties of the fibers are changed, at a constant fiber volume fraction. The model of a homogeneous transversely isotropic medium is adopted to describe the relations between elastic properties and velocities. The displacements due to an oscillatory point source in an infinite medium are used as one measure of comparison of the behavior of the unidirectional composite according to the variations of the parameters, as described above. Values of phase velocities, elastic moduli, Poisson's ratios and displacements due to a point source can be read from the parameterized plots for a known fiber volume fraction or a known ratio between extensional moduli of the composite. Alternatively fiber volume fraction and the ratio between extensional moduli can be inferred from the plots when the values of the phase velocities are known; for example from experimental measurements. Therefore, such parameterized curves may be useful in nondestructive mechanical property and material degradation characterizations.

Williams, J. H., Jr.↗

NASA NTRS1986

Modes of vibration on sqaure fiberglass epoxy composite thick plate

The frequencies and nodal patterns of a square thick plate of unidirectional fiberglass epoxy composite are measured experimentally. The constituent material is transversely isotropic. The plate is transversely excited at the center of the upper face, its resonant frequencies in the frequency range of 3 kHz to 21.73 kHz are detected and the measured nodal patterns are sketched.

Williams, J. H., Jr.↗

NASA NTRS1986

Wave propagation in anisotropic medium due to an oscillatory point source with application to unidirectional composites

The far-field displacements in an infinite transversely isotropic elastic medium subjected to an oscillatory concentrated force are derived. The concepts of velocity surface, slowness surface and wave surface are used to describe the geometry of the wave propagation process. It is shown that the decay of the wave amplitudes depends not only on the distance from the source (as in isotropic media) but also depends on the direction of the point of interest from the source. As an example, the displacement field is computed for a laboratory fabricated unidirectional fiberglass epoxy composite. The solution for the displacements is expressed as an amplitude distribution and is presented in polar diagrams. This analysis has potential usefulness in the acoustic emission (AE) and ultrasonic nondestructive evaluation of composite materials. For example, the transient localized disturbances which are generally associated with AE sources can be modeled via this analysis. In which case, knowledge of the displacement field which arrives at a receiving transducer allows inferences regarding the strength and orientation of the source, and consequently perhaps the degree of damage within the composite.

Williams, J. H., Jr.↗

NASA NTRS1986

Stress waves in transversely isotropic media: The homogeneous problem

The homogeneous problem of stress wave propagation in unbounded transversely isotropic media is analyzed. By adopting plane wave solutions, the conditions for the existence of the solution are established in terms of phase velocities and directions of particle displacements. Dispersion relations and group velocities are derived from the phase velocity expressions. The deviation angles (e.g., angles between the normals to the adopted plane waves and the actual directions of their propagation) are numerically determined for a specific fiber-glass epoxy composite. A graphical method is introduced for the construction of the wave surfaces using magnitudes of phase velocities and deviation angles. The results for the case of isotropic media are shown to be contained in the solutions for the transversely isotropic media.

Marques, E. R. C.↗

NASA NTRS1986

Stress waves in isotropic elastic plate excited by circular transducer

Steady state harmonic stress waves in an isotropic elastic plate excited on one face by a circular transducer are analyzed theoretically. The transmitting transducer transforms an electrical voltage into a uniform normal stress at the top of the plate. To solve the boundary value problem,the radiation into a half-space is considered. The receiving transducer produces an electrical voltage proportional to the average spatially integrated normal stress over its face due to an incident wave. A numerical procedure is given to evaluate the frequency response at a receiving point due to a multiply reflected wave in the near field. Its stability and convergence are discussed. Parameterization plots which determine the particular wave whose frequency response has maximum magnitude compared with other multiple reflected waves are given for a range of values of dimensionless parameters. The effects of changes in the values of the parameters are discussed.

Williams, J. H., Jr.↗

NASA NTRS1986

Pattern recognition characterizations of micromechanical and morphological materials states via analytical quantitative ultrasonics

One potential approach to the quantitative acquisition of discriminatory information that can isolate a single structural state is pattern recognition. The pattern recognition characterizations of micromechanical and morphological materials states via analytical quantiative ultrasonics are outlined. The concepts, terminology, and techniques of statistical pattern recognition are reviewed. Feature extraction and classification and states of the structure can be determined via a program of ultrasonic data generation.

Williams, J. H., Jr.↗

NASA NTRS1986

Input-output characterization of an ultrasonic testing system by digital signal analysis

Ultrasonic test system input-output characteristics were investigated by directly coupling the transmitting and receiving transducers face to face without a test specimen. Some of the fundamentals of digital signal processing were summarized. Input and output signals were digitized by using a digital oscilloscope, and the digitized data were processed in a microcomputer by using digital signal-processing techniques. The continuous-time test system was modeled as a discrete-time, linear, shift-invariant system. In estimating the unit-sample response and frequency response of the discrete-time system, it was necessary to use digital filtering to remove low-amplitude noise, which interfered with deconvolution calculations. A digital bandpass filter constructed with the assistance of a Blackman window and a rectangular time window were used. Approximations of the impulse response and the frequency response of the continuous-time test system were obtained by linearly interpolating the defining points of the unit-sample response and the frequency response of the discrete-time system. The test system behaved as a linear-phase bandpass filter in the frequency range 0.6 to 2.3 MHz. These frequencies were selected in accordance with the criterion that they were 6 dB below the maximum peak of the amplitude of the frequency response. The output of the system to various inputs was predicted and the results were compared with the corresponding measurements on the system.

Williams, J. H., Jr.↗

NASA NTRS1986

Ultrasonic testing of plates containing edge cracks

The stress wave factor (SWF) signal is utilized for the nondestructive evaluation of plates containing perpendicular edge cracks. The effects of the existence lateral location and depth of the crack on the magnitude spectra of individual reflections in the SWF signal are studied. If the reflections in the SWF signal are not overlapped the short time Fourier analysis is applied. If the reflections are overlapped the short time homomorphic analysis (cepstrum analysis) is applied. Several reflections which have average resonant frequencies approximately at 0.9, 1.3, and 1.7 MHz are analyzed. It is observed that the magnitude ratios evaluated at average resonant frequencies decrease more with increasing d/h if the crack is located between the transducers, where h is plate thickness and d is crack depth. Moreover, for the plates, crack geometries, reflections, and frequencies considered, the average decibel drop depends mainly on the dimensionless parameter d/h and it is approximately -1 dB per 0.07 d/h. Changes in the average resonant frequencies of the magnitude spectra are also observed due to changes in the location of the crack.

Williams, J. H., Jr.↗

NASA NTRS1985

Application of homomorphic signal processing to stress wave factor analysis

The stress wave factor (SWF) signal, which is the output of an ultrasonic testing system where the transmitting and receiving transducers are coupled to the same face of the test structure, is analyzed in the frequency domain. The SWF signal generated in an isotropic elastic plate is modelled as the superposition of successive reflections. The reflection which is generated by the stress waves which travel P times as a longitudinal (P) wave and s times as a shear (S) wave through the plate while reflecting back and forth between the bottom and top faces of the plate is designated as the reflection with P, s. Short-time portions of the SWF signal are considered for obtaining spectral information on individual reflections. If the significant reflections are not overlapped, the short-time Fourier analysis is used. A summary of the elevant points of homomorphic signal processing, which is also called cepstrum analysis, is given. Homomorphic signal processing is applied to short-time SWF signals to obtain estimates of the log spectra of individual reflections for cases in which the reflections are overlapped. Two typical SWF signals generated in aluminum plates (overlapping and non-overlapping reflections) are analyzed.

Williams, J. H., Jr.↗

NASA NTRS1985

Ultrasonic testing of plates containing edge cracks

Williams, J. H., Jr.↗

NASA NTRS1985

Promising quantitative nondestructive evaluation techniques for composite materials

Some recent results in the area of the ultrasonic, acoustic emission, thermographic, and acousto-ultrasonic NDE of composites are reviewed. In particular, attention is given to the progress in the use of ultrasonic attenuation, acoustic emission (parameter) delay, liquid-crystal thermography, and the stress wave factor in structural integrity monitoring of composite materials. The importance of NDE flaw significance characterizations is emphasized since such characterizations can directly indicate the appropriate NDE technique sensitivity requirements. The role of the NDE of flawed composites with and without overt defects in establishing quantitative accept/reject criteria for structural integrity assessment is discussed.

Williams, J. H., Jr.↗

NASA NTRS1985

Stress waves in an isotropic elastic plate excited by a circular transducer

Steady state harmonic stress waves in an isotropic elastic plate excited on one face by a circular transducer are analyzed theoretically. The transmitting transducer transforms an electrical voltage into a uniform normal stress at the top of the plate. To solve the boundary value problem, the radiation into a half-space is considered. The receiving transducer produces an electrical voltage proportional to the average spatially integrated normal stress over its face due to an incident wave. A numerical procedure is given to evaluate the frequency response at a receiving point due to a multiply reflected wave in the near field. Its stability and convergence are discussed. Parameterization plots which determine the particular wave whose frequency response has maximum magnitude compared with other multiple reflected waves are given for a range of values of dimensionless parameters. The effects of changes in the values of the parameters are discussed.

Karagulle, H.↗

NASA NTRS1985

Application of homomorphic signal processing to stress wave factor analysis

The stress wave factor (SWF) signal, which is the output of an ultrasonic testing system where the transmitting and receiving transducers are coupled to the same face of the test structure, is analyzed in the frequency domain. The SWF signal generated in an isotropic elastic plate is modelled as the superposition of successive reflections. The reflection which is generated by the stress waves which travel p times as a longitudinal (P) wave and s times as a shear (S) wave through the plate while reflecting back and forth between the bottom and top faces of the plate is designated as the reflection with p, s. Short-time portions of the SWF signal are considered for obtaining spectral information on individual reflections. If the significant reflections are not overlapped, the short-time Fourier analysis is used. A summary of the elevant points of homomorphic signal processing, which is also called cepstrum analysis, is given. Homomorphic signal processing is applied to short-time SWF signals to obtain estimates of the log spectra of individual reflections for cases in which the reflections are overlapped. Two typical SWF signals generated in aluminum plates (overlapping and non-overlapping reflections) are analyzed.

Karagulle, H.↗

NASA NTRS1984

Ultrasonic attenuation of a void-containing medium for very long wavelengths

Ultrasonic longitudinal through-thickness attenuation in an isotropic medium due to scattering by randomly distributed voids is considered analytically. The attenuation is evaluated on the assumption of no interaction between voids. The scattered power is assumed to be entirely lost, thus accounting for the ultrasonic attenuation. The scattered power due to the presence of a void is described in terms of the scattering cross section of the void. An exact solution exists for the scattering cross section of a spherical void. An approximate solution for the scattering cross section of an ellipsoidal void is developed based on the so-called Born approximation commonly used in quantum mechanics. This approximate solution is valid for k sub p a sub i much less than 1, where k sub p is the wave number of the incident longitudinal wave and a sub i is the largest dimension of the void. It is found that the shape of the void has negligible effect on the scattering cross section and that only the volume of the void is important. Thus, it is noted that in cases where k sub p a sub i is much less than 1, the exact scattering cross section of a spherical void having the same volume as an arbitrarily shaped void can be used for evaluating ultrasonic attenuation. Previously announced in STAR as N83-28466

Williams, J. H., Jr.↗

NASA NTRS1983

Effects of specimen resonances on acoustic-ultrasonic testing

Frequency response is studied at two different transducer locations in the 10-280 kHz range, for the case of the response of a solid 6061-T6 aluminum alloy block to the fracture of an 0.5 mm-diameter pencil lead, as well as to the impact of 0.159 and 0.318 cm-diameter stainless steel spheres. Prominent peaks in the pencil lead fracture and sphere impact spectra from the two transducer locations are found to exactly correspond to the alloy block's resonant frequencies, indicating that these have dominated the spectral content of the output signal. The spectral content is further influenced by the transducer location, relative to the resonant frequency nodal lines. The implications of these results for acoustic-ultrasonic parameters and measurements are discussed.

Williams, J. H., Jr.↗

NASA NTRS1983

Acoustic emission characterization using AE (parameter) delay

The acoustic emission (AE) parameter delay concept is defined as that particular measured value of a parameter at which a specified baseline level of cumulative AE activity is reached. The parameter can be from any of a broad range of elastic, plastic, viscoelastic, and fracture mechanics parameters, as well as their combinations. Such parameters include stress, load, strain, displacement, time, temperature, loading cycle, unloading stress, stress intensity factor, strain energy release rate, and crack tip plasticity zone size, while the AE activity may be AE event counts, ringdown counts, energy, event duration, etc., as well as their combinations. Attention is given to examples for the AE parameter delay concept, together with various correlations.

Williams, J. H., Jr.↗

NASA NTRS1983

Ultrasonic attenuation of a void-containing medium for very long wavelengths

Ultrasonic longitudinal through-thickness attenuation in an isotropic medium due to scattering by randomly distributed voids is considered analytically. The attenuation is evaluated on the assumption of no interaction between voids. The scattered power is assumed to be entirely lost, thus accounting for the ultrasonic attenuation. The scattered power due to the presence of a void is described in terms of the scattering cross section of the void. An exact solution exists for the scattering cross section of a spherical void. An approximate solution for the scattering cross section of an ellipsoidal void is developed based on the so-called Born approximation commonly used in quantum mechanics. This approximate solution is valid for k sub p a sub i 1, where k sub p is the wave number of the incident longitudinal wave and a sub i is the largest dimension of the void. It is found that the shape of the void has negligible effect on the scattering cross section and that only the volume of the void is important. Thus, it is noted that in cases where k sup p a sub i 1, the exact scattering cross section of a spherical void having the same volume as an arbitrarily shaped void can be used for evaluating ultrasonic attenuation.

Williams, J. H., Jr.↗