Search NASA⌕ Search

Engineering topics

Williams, Kent

Publications and source records attributed to Williams, Kent.

C Modules Enrichment

Module C1 discusses the step in the nuclear fuel cycle where the UF6 solid in cylinders from the conversion plant is processed to enrich the percentage of U-235 from 0.711% to the 3–5% typical of the enrichment used for light-water reactor nuclear fuel fabrication. It involves receipt of UF6 feed stock in 12.5 ton cylinders, enrichment operations, formation of enriched UF6 solid, and shipment of 2.3 ton cylinders to fuel fabricators. In this module, “SWU” is taken as shorthand for kg-SWU, the formal units for enrichment work, assuming that heavy metal mass flows will be gauged in kg.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Economic Impact of Closing the Nuclear Fuel Cycle

This report estimates the economic impact of closing the United States nuclear fuel cycle. Several different fuel cycle scenarios are analyzed. These scenarios include a baseline analysis of the existing fuel cycle conditions, a hypothetical scenario where all fuel cycle operations are preformed domestically, a scenario where all reactors are replaced with sodium fast reactors, and finally a scenario that uses a mix of fast reactors and light water reactors operating on mixed oxide fuel. Each scenario modeled is assumed to be operating at equilibrium and producing electricity at a 100 GWe-yr capacity. Impacts are calculated for normal operations and do not include construction or infrastructure expansion impacts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Advanced Fuel Cycle Cost Basis Report: Supporting Document 7 Presentation: Du and RU Disposal Costs [Slides]

Worldwide DU and RU in various chemical forms are some of the largest legacy products of the nuclear industry (defense & power) in both mass and volume. Chemical forms include U metal or alloy, UF6, UO2, UO3, U3O8, and UF4. Most of this material is now in above ground storage. Due to chemical stability and low water solubility oxides are the preferred form for safe storage and ultimate disposal. Long term U disposal in large amounts presents more of a potential radioactivity problem than its conversion and temporary storage. Now a near term problem with freshly-mined uranium ore, radon emanation will eventually be a long-term problem for both DU and RU dispositioned in large quantities at a specific location.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Advanced Fuel Cycle Cost Basis Report: Module D1-4 and Module D1-5 Ceramic Pelletized Sodium-Cooled Fast Reactor (SFR) Fuel Fabrication Ceramic Vibrocompacted Fuel Fabrication

This is a cost module that is part of the Advanced Fuel Cycle -- Cost Basis Report. Module D1-4: Nature of this module update (Rev 1) from previous advanced fuel cycle cost basis reports (AFCCBRs): new life cycle cost data on U,Pu SFR mixed oxide (MOX) fuels is derived from the Nonproliferation Assessment Systems Analysis Program (NASAP) conducted in the late 1970s. Highassay low-enriched uranium (HALEU) ceramic fuel is also discussed in more detail compared to earlier AFC-CBRs, since some advanced SFR concepts currently under development will require this HALEU fuel type for startup. Module D1-5: Nature of this FY-21 module update from previous AFC-CBRs: this module includes a few new references and a somewhat expanded discussion of vibrocompaction fuel fabrication technology. The WIT values for VIPAC are pegged directly to those for conventional LWR and SFR pelletized U,Pu MOX (note that this module now includes VIPAC MOX fuel for LWRs in addition to SFRs). Based on information from Russia, where VIPAC has been studied extensively, the unit costs are expressed as a percentage of those in the new updated Module D1-2 (pelletized U,Pu MOX) and new updated Module D1-4 (pelletized U,Pu MOX) for large NOAK fabrication facilities of the same production capacity. Since both ceramic pelletized MOX Modules D1-2 and D1-4 benefitted from analysis of 1970s NASAP data, by extension this Module D1-5 also benefits.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Advanced Fuel Cycle Cost Basis Report: Module D1-1: Uranium-based Ceramic LWR Fuel Fabrication (Rev.2)

Cost module on LWR fuel fabrication to accompany the Advanced Fuel Cycle Cost Basis Report. In this update, we are adding detailed life cycle cost data and a calculated, levelized fabrication cost derived from a non-proprietary bottom-up estimate prepared in 1978 by Oak Ridge National Laboratory (ORNL) (Judkins and Olsen 1978a). In 2018, the 1978 ORNL estimate was escalated by SA&I authors to 2017 USD using factors that represent inflation, escalation above inflation typical of nuclear projects, and the effects of more stringent safety and environmental regulations. In this FY-21 document, the $/kgU results in 2017 USD from the unpublished 2018 interim study (Williams and Ganda 2018) can be escalated to 2020 USD using a factor of 1.052. The literature-based unit cost (or price) data from previous (2004–2017) AFC-CBRs are escalated to 2020 USD using factors from Chapter 8 of the main FY-21 AFC-CBR document. This data, in addition to the results of the updated bottom-up estimate, are used to define the “what-it-takes” (WIT) range for the unit fabrication costs for conventional ceramic UOX light-water reactor (LWR) fuel. This FY-23 document also includes calculated unit costs for accident-tolerant LWR fuels (ATFs) of three different types. Some of these fuels constitute a ceramic pelletized form with fuel meat uranium compounds other than UO2 (a.k.a.,. UOX), thus the change in the title of this module in which the word “UO2” is changed to “Uranium-based Ceramic.”

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Module D-PR Fuel Fabrication Preface to the D-Modules

Generic Technical Factors Affecting Fuel Fabrication. Many in-reactor physical, chemical, metallurgical, mechanical, thermodynamic, and nucleonic factors influence the design and functionality of nuclear fuel. Detailed discussion of these technical factors is beyond the scope of this cost-oriented preface document; however, the following three references are suggested for a more comprehensive discussion of fuel design requirements for both commercial and special use (military and remote location) reactors: IAEA-TECDOC-1686 (IAEA 2012), the World Nuclear Association webpage “Nuclear Fuel and its Fabrication (WNA 2020a), and INL/EXT-20-54641 (Mariani 2020). To aid the reader’s understanding of how design affects life cycle costs, a few technical factors are also briefly discussed in the sections below.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗