Search NASA⌕ Search

Engineering topics

Williams, M. C.

Publications and source records attributed to Williams, M. C..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Transfer of perceptual-motor training and the space adaptation syndrome

Perceptual cue conflict may be the basis for the symptoms which are experienced by space travelers in microgravity conditions. Recovery has been suggested to take place after perceptual modification or reinterpretation. To elucidate this process, 10 subjects who repeatedly experienced a visual/vestibular conflict over trials and days, were tested in a similar but not identical perceptual situation (pseudo-Coriolis) to determine whether any savings in perceptual adaptation had occurred as compared to an unpracticed control group (N = 40). The practiced subjects experienced lessening dizziness and ataxia within and over sessions.

Kennedy, R. S.↗
NASA NTRS1982

Rotor redesign for a highly loaded 1800 ft/sec tip speed fan. 3: Laser Doppler velocimeter report

Laser Doppler velocimeter (LDV) techniques were employed for testing a highly loaded, 550 m/sec (1800 ft/sec) tip speed, test fan stage, the objective to provide detailed mapping of the upstream, intrablade, and downstream flowfields of the rotor. Intrablade LDV measurements of velocity and flow angle were obtained along four streamlines passing through the leading edge at 45%, 69%, 85%, and 95% span measured from hub to tip, at 100% of design speed, peak efficiency; 100% speed, near surge; and 95% speed, peak efficiency. At the design point, most passages appeared to have a strong leading edge shock, which moved forward with increasing strength near surge and at part speeds. The flow behind the shock was of a complex mixed subsonic and supersonic form. The intrablade flowfields were found to be significantly nonperiodic at 100% design speed, peak efficiency.

Harvey, W. B.↗
NASA NTRS1982

Anti-misting additives for jet fuels

The ignition characteristics of sprays, created by wind shear action, of Jet-A fuel containing polyisobutylene additives wee examined over ranges of air velocities from 45 to 90 m/s and of fuel/air mass ratios of 0.20 to 8.0. Ignition was by calibrated sparks of energies up to about 0.5 J and by a butane/oxygen flame at 165 J/s. The polymeric additives studied included the grades L80, L160, and L200 from Exxon Chemical and B200 and B230 from BASF. The ignition suppression ability of the additives, as well as their observed anti-misting (AM) behavior, ranked exactly as their molecular weights (viscosity average, M sub v) with 400-500 ppm of L80 (M sub v = 0.68 x 1,000,000) being required to suppress ignition of a spray at 51 m/s, 1.8 fuel/air mass ratio, by a 0.55 J spark while only 10 ppm of B230 (M sub v = 7.37 x 1,000,000) was required for the same conditions. The additive concentrations (L160) required for ignition suppression increased with increasing air velocity and with increasing fuel/air ratio.

Grens, E. A., II↗
NASA NTRS1982

Viscometric and misting properties of polymer-modified fuel

Solutions of polyisobutylenes L160, L200, B200, and B230 in Jet-A were prepared at concentrations up to 3000 ppm. These polymers have molecular weights in the range 5 to 9 x 1,00,000 and have previously been shown to induce anti-misting properties in Jet-A. In connection with the pumpability of such solutions, especially at low temperatures, the shear viscosity, eta, of these solutions was measured at temperatures 25 C, 0 C, and -25 C. Concentration-dependence of eta was very similar for all four polymer solutes, the increase of eta(c) at 3000 ppm being roughly four-fold (relative to Jet-A) for the L-series and five-fold for the B-series. This behavior prevailed at all temperatures, and there was no evidence of phase separation or other chemical instability at -25 C at any concentration. In the more practical c-range for anti-misting applications, say within 1000 ppm, the increase of eta(c) was only twofold.

Grens, E. A., II↗
NASA NTRS1974

The application of holography to the visualization of shock patterns in a transonic compressor

This paper describes an experiment in the application of holographic interferometry to the visualization of flow in a transonic compressor. The principal objective of the study was to visualize the shock waves created by the rotor blades and to determine their relative orientation in three dimensions. The technique employed double-pulse, double-exposure holography to record the flow field through a plastic window built into the outer case over the rotor blades. Illumination was by diffuse reflection from the interior surfaces of the compressor. No other optical components in or on the compressor were used. The resulting holograms successfully showed the upstream bow shocks and, at high speed, the outer-most portion of the leading edge passage shock. Techniques were devised for locating these shocks in three dimensions and the results were compared with theoretical predictions. In all cases, the shock angles were somewhat larger than predicted by theory, and a distinct increase in angle near the outer wall was observed, which may be attributed to end wall boundary layer effects.

Hantman, R. G.↗
NASA NTRS1973

Application of holography to the determination of flow conditions within the rotating blade row of a compressor

The double-pulse, double-exposure holography technique was applied to visualize the flow field within a transonic compressor rotor with a tip speed of 1800 ft/sec. The principal objective was to visualize the shock waves created in the flow field which was supersonic relative to the rotating blade row. The upstream rotor blade bow shocks and, at high speed, the outermost portion of the leading edge passage shock were successfully observed in the holograms. Techniques were devised for locating these shocks in three dimensions, and the results were compared with theoretical predictions. Density changes between the two pulses due to motion of the shocks were large and, therefore, it was not possible to resolve the fringe systems in detail for the 100% speed conditions. However, gross features of the shocks were easily observed, and the upstream shocks were well displayed. In all cases the shock angles were somewhat larger than predicted by theory, and a distinct increase in angle near the outer wall was observed, which may be attributed to endwall boundary layer effects. The location and orientation of the observed leading edge passage shocks were in good agreement with static pressure contours obtained from measurements in the outer casing over the rotor tip.

Hantman, R. G.↗