Search NASA⌕ Search

Engineering topics

Williams, M. L.

Publications and source records attributed to Williams, M. L..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Faired instrumentation for aerodynamic tests

Streamlined package is installed and removed without altering aerodynamic properties of structure being tested. Method uses lightweight materials so that blade balance is maintained.

Long, W. C.↗
NASA NTRS1978

A rotor-mounted digital instrumentation system for helicopter blade flight research measurements

A rotor mounted flight instrumentation system developed for helicopter rotor blade research is described. The system utilizes high speed digital techniques to acquire research data from miniature pressure transducers on advanced rotor airfoils which are flight tested on an AH-1G helicopter. The system employs microelectronic pulse code modulation (PCM) multiplexer digitizer stations located remotely on the blade and in a hub mounted metal canister. As many as 25 sensors can be remotely digitized by a 2.5 mm thick electronics package mounted on the blade near the tip to reduce blade wiring. The electronics contained in the canister digitizes up to 16 sensors, formats these data with serial PCM data from the remote stations, and transmits the data from the canister which is above the plane of the rotor. Data are transmitted over an RF link to the ground for real time monitoring and to the helicopter fuselage for tape recording. The complete system is powered by batteries located in the canister and requires no slip rings on the rotor shaft.

Knight, V. H., Jr.↗
NASA NTRS1974

Mixed mode stress field effect in adhesive fracture

Numerical or analytical analyses were performed on seven different test specimens including blister test, 90-degree peel test, torsion test, and various cone tests. These specimens are in general subjected to complex stress fields having various amounts of Mode I, Mode II, and Mode III loads. The specimens were then constructed using polymethyl methacrylate for the adherends and a transparent polyurethane elastomer (Solithane 113) for the adhesive. This combination permitted direct observation of the bondline as load was applied. Although initial debonds as well as bond end termination singularities were present in all specimens, in some cases the debond did not initiate at the singularity points as would normally have been expected. An explanation for this behavior is presented, as well as a comparison of loading mode effect on those specimens for which the debond did propagate from a bond terminus singular point.

Anderson, G. P.↗
NASA NTRS1974

The peel test in experimental adhesive fracture mechanics

Several testing methods have been proposed for obtaining critical energy release rate or adhesive fracture energy in bond systems. These tests include blister, cone, lap shear, and peel tests. Peel tests have been used for many years to compare relative strengths of different adhesives, different surface preparation techniques, etc. The present work demonstrates the potential use of the peel test for obtaining adhesive fracture energy values.

Anderson, G. P.↗
NASA NTRS1974

Adhesive fracture mechanics

In studies of fracture mechanics the adhesive fracture energy is regarded as a fundamental property of the adhesive system. It is pointed out that the value of the adhesive fracture energy depends on surface preparation, curing conditions, and absorbed monolayers. A test method reported makes use of a disk whose peripheral part is bonded to a substrate material. Pressure is injected into the unbonded central part of the disk. At a certain critical pressure value adhesive failure can be observed. A numerical stress analysis involving arbitrary geometries is conducted.

Bennett, S. J.↗
NASA NTRS1973

The effects of plasticity in adhesive fracture

An energy-balance analysis is presented for adhesive failure in end loaded cantilever beams. The analysis includes the effects of input work, stored strain energy, dissipated plastic energy, and specific adhesive surface energy. Experimental results obtained with 6061-T6 aluminum are presented as evidence for the validity of the approach.-

Chang, M. D.↗
NASA NTRS1972

A fracture mechanics analysis of adhesive failure in a single lap shear joint.

Discussion of adhesive fracture of single lap shear joints in terms of a maximum stress criterion and an energy balance. The Goland and Reissner (1944) analysis is used to determine the stress distribution in the adhesive assembly, and the results obtained are introduced into an energy balance to determine the initiation of adhesive fracture. In the stress analysis the loads at the edges of the joint are first determined. This is a problem in which the deformation of the joint sheets must be taken into account and is solved by using the finite-deflection theory of cylindrically bent plates. Then the stress in the joint due to applied loads is determined. This problem is formulated as one in plane strain consisting of two rectangular sheets of equal thickness and unit width. With the aid of this stress analysis and the stresses obtained from the conditions of equilibrium the contributions to the energy change with crack length are calculated. The analysis performed is then compared with a maximum stress criterion for a lap joint.

Devries, K. L.↗
NASA NTRS1971

EPR-atomic scale experimental stress analysis

Electron paramagnetic resonance atomic scale stress analysis of high polymer fibers and rubber, measuring chain scission and bond rupture for different loading histories

Devries, K. L.↗
NASA NTRS1971

Formation of free radicals during mechanical degradation of elastomers.

Solithane 113 (an amorphous polyurethane elastomer) was prepared by curing equal proportions of castor oil and trifunctional isocyanate for 6 hr 45 min at 170 F. The sample material was mechanically degraded by grinding below and above its glass transition point at liquid nitrogen and room temperatures. The EPR spectra of ground samples were recorded and the number of free radicals were determined by a computer double-integration of the recorded spectra and by a comparison of the values with those of a standard material. Curves of EPR spectra suggest that different molecular mechanisms may be active in degradation of this material below and above its glass transition temperature.

Devries, K. L.↗