Search NASA⌕ Search

Engineering topics

Williford, Ralph E

Publications and source records attributed to Williford, Ralph E.

Ambient Operation of Li/Air Batteries

In this work, Li/air batteries based on nonaqueous electrolytes were investigated in ambient conditions (with an oxygen partial pressure of 0.21 atm and relative humidity of ~20%). A heat-sealable polymer membrane was used as both an oxygen-diffusion membrane and as a moisture barrier for Li/air batteries. The membrane also can minimize the evaporation of the electrolyte from the batteries. Li/air batteries with this membrane can operate in ambient conditions for more than one month with a specific energy of 362 Wh kg-1, based on the total weight of the battery including its packaging. Among various carbon sources used in this work, Li/air batteries using Ketjenblack (KB) carbon-based air electrodes exhibited the highest specific energy. However, KB-based air electrodes expanded significantly and absorbed much more electrolyte than electrodes made from other carbon sources. The weight distribution of a typical Li/air battery using the KB-based air electrode was dominated by the electrolyte (~70%). Lithium-metal anodes and KB-carbon anodes account for only 5.12% and 5.78% of the battery weight, respectively. We also found that only ~ 20% of the mesopore volume of the air electrode was occupied by reaction products after discharge. To further improve the specific energy of the Li/air batteries, the microstructure of the carbon electrode needs to be further improved to absorb much less electrolyte while still holding significant amounts of reaction products

energy storage↗

Effect of entropy of lithium intercalation in cathodes and anodes on Li-ion battery thermal management

The entropy changes (ΔS) in various cathode and anode materials, as well as complete Li-ion batteries, were measured using an electrochemical thermodynamic measurement system (ETMS). LiCoO 2 has a much larger entropy change than electrodes based on LiNi x Co y Mn z O 2 and LiFePO 4 , while lithium titanate based anode has lower entropy change compared to graphite anodes. Reversible heat generation rate was found to be a significant portion of the total heat generation rate. The appropriate combinations of cathode and anode were investigated to minimize reversible heat.

25 ENERGY STORAGE↗

Optimization of Air Electrode for Li/Air Batteries

The effects of carbon microstructure and carbon loading on the performance of Li/air batteries were investigated. The active carbons from various sources were compared, and a dry rolling method was optimized to prepare air electrodes with high mesopore volume. It is found that the capacities of air electrodes improve significantly when the mesopore volume of the carbon source is high. However, for carbons with low mesopore volumes, other factors such as surface activity also play an important role in determining the electrochemical performances of the Li/air batteries. A practical criterion, area-specific capacity, was used to optimize the carbon loading for air electrode. The best area-specific capacity of 13.1 mAh/cm2 was obtained at a carbon loading of 15.1 mg/cm2. Further increasing or decreasing the carbon loading led to a reduced area- specific capacity. Finally, at fixed carbon loading and discharge rates, electrolyte amount was another key factor governing cell performance. A spring mechanism is proposed to explain the formation of the tri-phase regions in air electrodes. After optimizing the parameters listed above, a high capacity of 1,756 mAh/g carbon corresponding to a specific energy of 4,614 Wh/kg carbon was obtained for Li/air batteries operated in a dry air environment.

25 ENERGY STORAGE↗

An Integrated Approach to Coal Gasifier Testing, Modeling, and Process Optimization

Gasification is an important method of converting coal into clean burning fuels and high-value industrial chemicals. However, gasifier reliability can be severely limited by rapid degradation of the refractory lining in hot-wall gasifiers. The Pacific Northwest National Laboratory (PNNL) is performing multidisciplinary research to provide the experimental data and the engineering models needed to control gasifier operation for extended refractory life. Our experimental program includes prediction of slag viscosity using empirical viscosity models encompassing US coals, characterization of selected slag-refractory interaction including transport of slag/refractory components at the slag-refractory interface, and measurement of slag penetration into refractories as a function of time and temperature. The experimental data is used in slag flow, slag penetration, and refractory damage models to predict the operating temperature limits for increased refractory life. A simplified entrained flow gasifier model is also being developed to simulate one-dimensional axial flow with average axial velocity, coal devolatilization, and combustion kinetics. Combining the slag flow, refractory degradation, and gasifier models will provide a powerful tool to predict the coal and oxidant feed rates and control the gasifier operation to balance coal conversion efficiency with increased refractory life. A research scale gasifier has also been constructed at PNNL to provide syngas for coal conversion and carbon sequestration research, and also valuable datasets on operating conditions for validating the modeling results.

01 COAL, LIGNITE, AND PEAT↗

Air Electrode Design for Sustained High Power Operation of Li/air Batteries

The rapid development of portable electronic devices increasingly requires much more energy to support advanced functions. However, currently available batteries do not meet the high energy requirement of these devices. Metal/air batteries, especially Li/air batteries, have a much higher specific energy than most other available batteries, but their power rate is limited by the accumulation of reaction products in the air electrode. Several approaches to improve the power rate of Li/air batteries have been analyzed in this work, including adjustment of air electrode porosity and catalyst reactivity distributions to minimize diffusion limitations and maximize air electrode material utilization. An interconnected dual pore system (one catalyzed and one noncatalyzed) is proposed to improve oxygen transport into the inner regions of the air electrode, but this approach alone cannot supply high power for long term applications. A time-release multiple catalyst approach is analyzed to provide temporal release of reactivity in the air electrode. When coupled with the dual pore configuration and catalysts with high reactivities, the time-release catalyst concept can extend the duration of higher powers to longer times, and result in maximum utilization of air electrode materials.

Williford, Ralph E↗

Low-Temperature Densification of Lanthanum Strontium Manganite (La1-xSrxMnO3+δ), x=0.0-0.20

Intermediate-stage sintering of lanthanum strontium manganite (LSM, where Sr=0.00, 0.05, 0.10, 0.15, and 0.20) was shown in dilatometry studies to be accelerated when subjected to alternating flows of air and nitrogen. The extent of rate enhancement decreased with increased Sr content, and decreases with increased temperature, which coincides with diminished oxygen non-stoichiometry. Shrinkage rates were shown further to be sensitive to the difference in oxygen content in the alternating gas flows. Baseline air sintering rates were measured using stepwise isothermal dilatometry, from which kinetic parameters were calculated using the Makipirtti-Meng model. Activation energies for sintering in air were determined to be 255±26, 258±28, 308±32, 373±37, and 417±41 kJ/mol for Sr=0.0, 0.05, 0.10, 0.15, and 0.20, respectively. A diffusion-based model is proposed that is consistent with trends in accelerated shrinkage versus temperature. Transient cation vacancy gradients, which lead to higher cation mobility, were calculated from established oxygen diffusivities and oxygen non-stoichiometry as a function of temperature and time. A potential application of this approach is processing of LSM-based cathode-side contact pastes in solid oxide fuel cells.

30 DIRECT ENERGY CONVERSION↗

Fatigue Testing of Abrasive Water Jet Cut Titanium

Battelle Memorial Institute as part of its U.S. Department of Energy (USDOE) Contract No. DE-AC05-76RL01830 to operate the Pacific Northwest National Laboratory (PNNL) provides technology assistance to qualifying small businesses in association with a Technology Assistance Program (TAP). Qualifying companies are eligible to receive a set quantity of labor associated with specific technical assistance. Having applied for a TAP agreement to assist with fatigue characterization of Abrasive Water Jet (AWJ) cut titanium specimens, the OMAX Corporation was awarded TAP agreement 09-02. This program was specified to cover dynamic testing and analysis of fatigue specimens cut from titanium alloy Ti-6%Al-4%V via AWJ technologies. In association with the TAP agreement, a best effort agreement was made to characterize fatigue specimens based on test conditions supplied by OMAX.

36 MATERIALS SCIENCE↗