Engineering topics

Willis, C. M.

Publications and source records attributed to Willis, C. M..

At least 19 records

NASA NTRS1987

Propeller aircraft interior noise model. II - Scale-model and flight-test comparisons

A program for predicting the sound levels inside propeller driven aircraft arising from sidewall transmission of airborne exterior noise is validated through comparisons of predictions with both scale-model test results and measurements obtained in flight tests on a turboprop aircraft. The program produced unbiased predictions for the case of the scale-model tests, with a standard deviation of errors of about 4 dB. For the case of the flight tests, the predictions revealed a bias of 2.62-4.28 dB (depending upon whether or not the data for the fourth harmonic were included) and the standard deviation of the errors ranged between 2.43 and 4.12 dB. The analytical model is shown to be capable of taking changes in the flight environment into account.

Willis, C. M.↗

NASA NTRS1985

Effects of propeller rotation direction on airplane interior noise levels

Interior noise measurements for upsweeping and downsweeping movement of the propeller blade tips past the fuselage were made on a twin-engine airplane and on two simplified fuselage models. Changes in interior noise levels of as much as 8 dB reversal of propeller rotation direction were measured for some configurations and test conditions.

Willis, C. M.↗

NASA NTRS1984

Noise-reduction measurements of stiffened and unstiffened cylindrical models of an airplane fuselage

Noise-reduction measurements are presented for a stiffened and an unstiffened model of an airplane fuselage. The cylindrical models were tested in a reverberant-field noise environment over a frequency range from 20 Hz to 6 kHz. An unstiffened metal fuselage provided more noise reduction than a fuselage having the same sidewall weight divided between skin and stiffening stringers and ring frames. The addition of acoustic insulation to the models tended to smooth out the interior-noise spectrum by reducing or masking the noise associated with the structural response at some of the resonant frequencies.

Willis, C. M.↗

NASA NTRS1983

Aircraft interior noise models - Sidewall trim, stiffened structures, and cabin acoustics with floor partition

As part of the continuing development of an aircraft interior noise prediction model, in which a discrete modal representation and power flow analysis are used, theoretical results are considered for inclusion of sidewall trim, stiffened structures, and cabin acoustics with floor partition. For validation purposes, predictions of the noise reductions for three test articles (a bare ring-stringer stiffened cylinder, an unstiffened cylinder with floor and insulation, and a ring-stringer stiffened cylinder with floor and sidewall trim) are compared with measurements.

Pope, L. D.↗

NASA NTRS1982

Development and validation of preliminary analytical models for aircraft interior noise prediction

Predictions are made of the transmission of sound into an unpressurized and unstiffened cylinder under random and harmonic excitations, in order to validate the preliminary version of an airplane interior noise prediction model which is based on an analysis of the power flow type. The predictions are compared to experimental results, and statistically significant differences between predictions and measurements are found to be primarily due to input data deficiencies. Because the model requires only the value of a simple integral for determining interior spatial coupling, and resonance frequencies to determine frequency coupling, the known dynamics of the fuselage can be utilized without difficulty.

Pope, L. D.↗

NASA NTRS1981

Experimental study of noise reduction for an unstiffened cylindrical model of an airplane fuselage

Noise reduction measurements were made for a simplified model of an airplane fuselage consisting of an unstiffened aluminum cylinder 0.5 m in diameter by 1.2 m long with a 1.6-mm-thick wall. Noise reduction was first measured with a reverberant field pink-noise load on the cylinder exterior. Next, noise reduction was measured by using a propeller to provide a more realistic noise load on the cylinder. Structural resonance frequencies and acoustic reverberation times for the cylinder interior volume were also measured. Comparison of data from the relatively simple test using reverberant-field noise with data from the more complex propeller-noise tests indicates some similarity in both the overall noise reduction and the spectral distribution. However, all of the test parameters investigated (propeller speed, blade pitch, and tip clearance) had some effect on the noise-reduction spectra. Thus, the amount of noise reduction achieved appears to be somewhat dependent upon the spectral and spatial characteristics of the flight conditions. Information is also presented on cyclinder resonance frequencies, damping, and characteristics of propeller-noise loads.

Willis, C. M.↗

NASA NTRS1979

Experimental study of acoustic loads on an upper-surface-blown STOL airplane configuration

Fluctuating pressure levels were measured on the flap and fuselage of an upper-surface-blown jet-flap airplane configuration in a wind tunnel. The model tested had turbofan engines with a bypass ratio of 3 and a thrust rating of 10 kN. Rectangular nozzles were mounted flush with the upper surface at 35 percent of the wing chord. Test parameters were flap deflection angle, jet impingement angle, angle of attack, free-stream velocity, spanwise location of the engine, and jet dynamic pressure. Load levels were high throughout the jet impingement region, with the highest levels (about 159 dB) occurring on the fuselage and near the knee of the flap. The magnitude of the forward-velocity effect appeared to depend upon the ratio of free-stream and jet velocities. Good agreement was obtained between fluctuating pressure spectra measured at jet dynamic pressures of 7 and 22 kPa when the spectra were scaled by nondimensional functions of dynamic pressure, velocity, and the empirical relationship between dynamic pressure and overall fluctuating pressure level.

Willis, C. M.↗

NASA NTRS1979

Fluctuating loads measured on an over-the-wing supersonic jet model

Fluctuating pressure loads on the wing and flap of an over-the-wing supersonic jet model were measured. The model was tested statically and at a Mach number of 0.1 in a small free jet to simulate forward speed. Test parameters were impingement angle, nozzle height, and flap deflection. Load levels as high as 170 db were measured at the center of the impingement region during static tests. Forward speed reduced the loading about 1 db. Load level increased with increasing impingement angle and decreasing nozzle height above the wing. The effect of flap deflection was small. When scaled to full-size aircraft conditions, the maximum amplitude of the one-third-octave fluctuating pressure spectra was about 154 db at about 160 Hz. Maximum load level occurred near the intersection of the nozzle center line with the impinged surface. Downstream of the maximum the fluctuating pressure is inversely proportional to the distance downstream of the nozzle.

Willis, C. M.↗

NASA NTRS1977

Acoustic loads on upper-surface-blown powered-lift systems

Powered-lift concepts are utilized in aircraft currently under development for STOL application. One of the concepts, upper surface blowing, places the jet exit just above the upper surface of the wing to produce powered lift from the jet exhaust blowing over the deflected flap. New data are presented to show the effects of airspeed, angle of attack, and angle of jet impingement. Scaling relationships are investigated concerning their applicability for extrapolating data to a different model size. The effects of a number of test parameters are examined and full-scale spectra are predicted from model data. It is concluded that scale models are an effective means for obtaining fluctuating pressure spectra for use in aircraft design. The prediction of full-scale loads from model data will require geometrically accurate models and closely spaced measurement locations.

Willis, C. M.↗

NASA NTRS1976

Effects of aircraft noise on flight and ground structures

Acoustic loads measured on jet-powered STOL configurations are presented for externally blown and upper surface blown flap models ranging in size from a small laboratory model up to a full-scale aircraft model. The implications of the measured loads for potential acoustic fatigue and cabin noise are discussed. Noise transmission characteristics of light aircraft structures are presented. The relative importance of noise transmission paths, such as fuselage sidewall and primary structure, is estimated. Acceleration responses of a historic building and a residential home are presented for flyover noise from subsonic and supersonic aircraft. Possible effects on occupant comfort are assessed. The results from these three examples show that aircraft noise can induce structural responses that are large enough to require consideration in the design or operation of the aircraft.

Mixson, J. S.↗

NASA NTRS1976

Acoustic-loads research for powered-lift configurations

Data presented from large-scale model tests with jet engines having thrusts of 9 kN (2000 lb) and 36 kN (8000 lb) include acoustic loads for an externally blown wing and flap induced by a TF34 jet engine, an upper surface blown (USB) aircraft model in a wind tunnel, and two USB models in static tests. Comparisons of these results with results from acoustic loads studies on configurations of other sizes are made and the implications of these results on interior noise and acoustic fatigue are discussed.

Schoenster, J. A.↗

NASA NTRS1975

Fluctuating pressures on aircraft wing and flap surfaces associated with powered-lift systems

The present work presents results from two research studies that provide information on the fluctuating pressures generated by the use of powered-lift systems in STOL aircraft. Data are given for several chordwise and spanwise locations on large-scale models of an externally blown flap (EBF) configuration and an upper surface blown flap (USB) configuration in which actual jet engines were used. Pressure levels were high enough to indicate that special design effort will be required to avoid acoustic fatigue failures of wing and flap sturctures. The observation that pressure levels did not decrease very much with increased distance from the engine exhaust center line suggests that a STOL aircraft fuselage, which is in relatively close proximity to the engines for aerodynamic reasons, will be subjected to unusually high external overall fluctuating pressure levels (OAFPLs) that may cause difficulty in control of the cabin noise level.

Mixson, J. S.↗

NASA NTRS1973

Parametric studies of the wing flutter behavior of a STOL transport.

A computer study was conducted to evaluate the effects of variations in the principal structural parameters on the wing flutter behavior of a four-engine STOL transport configuration having relatively low inplane wing stiffness and heavy engines. The wing structure was represented by a finite-element model which included the coupling between inplane and out-of-plane motion of the wing induced by the offset engine masses. The parameters which were varied were engine mass, pylon stiffness, and the inplane stiffness of the wing. It was found that the value of inplane stiffness for best flutter performance lies substantially below the range encountered in conventional designs. For engine weights in the medium-to-heavy range, the best inplane stiffness provided a dramatic improvement in flutter performance over that for infinite inplane stiffness, while for the lightest engines the improvement was moderate.

Kyser, A. C.↗

NASA NTRS1972

Static structural tests of a 1.5-meter diameter fabric attached inflatable decelerator

Meridional tape forces, permeability, and change in model contours were measured on the aft half of a 1.5-m-diameter attached inflatable decelerator (AID). Inflation pressures up to 103 kN per square meter and external pressures of 0.14 to 102 kN per square meter were used. The results indicated that the model stresses were near the desired isotensoid condition. Future AID designs should consider both stiffness and strength of the meridional tapes to obtain the optimum division of load between tapes and fabric. Permeability of pressurized fabric structures is a few orders of magnitude higher than that obtained in the standard low-pressure test on material specimens.

Willis, C. M.↗

NASA NTRS1970