Search NASA⌕ Search

Engineering topics

Wilson, J R

Publications and source records attributed to Wilson, J R.

At least 19 records

Current ramp-up with lower hybrid current drive in EAST

More economical fusion reactors might be enabled through the cyclic operation of lower hybrid current drive. The first stage of cyclic operation would be to ramp up the plasma current with lower hybrid waves alone in low-density plasma. Such a current ramp-up was carried out successfully on the EAST tokamak. The plasma current was ramped up with a time-averaged rate of 18 kA/s with lower hybrid (LH) power. The average conversion efficiency P{sub el}/P{sub LH} was about 3%. Over a transient phase, faster ramp-up was obtained. These experiments feature a separate measurement of the L/R time at the time of current ramp up.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Effects of the Scattering by Edge Plasma Density Fluctuations on Lower Hyybrid Wave Propagation

Scattering effects induced by edge density fluctuations on lower hybrid (LH) wave propagation are investigated. The scattering model used here is based on the work of Bonoli and Ott [Phys. Fluids 25 (1982) 361]. It utilizes an electromagnetic wave kinetic equation solved by a Monte Carlo technique. This scattering model has been implemented in GENRAY , a ray tracing code which explicitly simulates wave propagation, as well as collisionless and collisional damping processes, over the entire plasma discharge, including the scrape-off layer (SOL) that extends from the separatrix to the vessel wall. A numerical analysis of the LH wave trajectories and the power deposition profile with and without scattering is presented for Alcator CMod discharges. Comparisons between the measured hard x-ray emission on Alcator C-Mod and simulations of the data obtained from the synthetic diagnostic included in the GENRAY/CQL3D package are shown, with and without the combination of scattering and collisional damping. Implications of these results on LH current drive are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Paraxial Wentzel-Kramers-Brillouin method applied to the lower hybrid wave propagation

The paraxial Wentzel-Kramers-Brillouin (pWKB) approximation, also called beam tracing method, has been employed in order to study the propagation of lower hybrid waves in a tokamak plasma. Analogous to the well-know ray tracing method, this approach reduces Maxwell's equations to a set of ordinary differential equations, while, in addition, retains the effects of the finite beam cross-section, and, thus, the effects of diffraction. A new code, LHBEAM (lower hybrid BEAM tracing), is presented, which solves the pWKB equations in tokamak geometry for arbitrary launching conditions and for analytic and experimental plasma equilibria. In addition, LHBEAM includes linear electron Landau damping for the evaluation of the absorbed power density and the reconstruction of the wave electric field in both the physical and Fourier space. Illustrative LHBEAM calculations are presented along with a comparison with the ray tracing code GENRAY and the full wave solver TORIC-LH.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Operating The Upgraded NSTX HHFW Antenna Array In An Environment With Li-coated Surfaces

The single-feed, end-grounded straps of the NSTX 12-strap HHFW antenna array have been replaced with double-feed, center-grounded straps to reduce the voltages in the vicinity of the Faraday shield (FS) for a given strap current. The strap spacings to the FS and to the back plate were increased by 3 mm to decrease the electric fields for a given voltage. The electric fields near the FS have been roughly halved for the same strap currents, permitting a direct examination of the roles that internal fields play in determining antenna power limits in plasmas. Extensive RF/plasma conditioning of the antenna was required to remove enough of the evaporated Li deposits from prior wall conditioning to permit coupling in excess of 4 MW to L- and H-mode plasmas in 2009. Most arcs were associated with expulsion of Li from the FS/antenna frame surfaces. The center-grounded straps were less susceptible to arcing during ELMing H-mode plasmas. Reliable operation above 2 MW was difficult after the installation of the Liquid Lithium Divertor (LLD) in 2010. Li-compound 'dust' was found in the antennas after this run and is believed to have contributed to the reduced power limit.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Lower Hybrid Wave Induced SOL Emissivity Variation at High Density on the Alcator C-Mod Tokamak

Lower Hybrid Current Drive (LHCD) in the Alcator C-Mod tokamak provides current profile control for the generation of Advanced Tokamak (AT) plasmas. Non-thermal electron bremsstrahlung emission decreases dramatically at n-bar{sub e}>1{center_dot}10{sup 20}[m{sup -3}] for diverted discharges, indicating low current drive efficiency. It is suggested that Scrape-Off-Layer (SOL) collisional absorption of LH waves is the cause for the absence of non-thermal electrons at high density. VUV and visible spectroscopy in the SOL provide direct information on collision excitation processes. Deuterium Balmer-, Lyman- and He-I transition emission measurements were used for initial characterization of SOL electron-neutral collisional absorption. Data from Helium and Deuterium LHCD discharges were characterized by an overall increase in the emissivity as well as an outward radial shift in the emissivity profile with increasing plasma density and applied LHCD power. High-temperature, high-field (T{sub e} = 5keV,B{sub t} = 8T) helium discharges at high density display increased non-thermal signatures as well as reduced SOL emissivity. Variations in emissivity due to LHCD were seen in SOL regions not magnetically connected to the LH Launcher, indicating global SOL effects due to LHCD.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Recent Results on Coupling Fast Waves to High Performance Plasmas on DIII-D

Fast Waves (FWs) at 60 MHz and 90 MHz are used in DIII-D for central electron heating and current drive. Coupling of FWs to high-performance discharges is limited by low antenna loading in these regimes. To extend the application of high-power FWs to such regimes, methods of increasing the antenna loading in these regimes are needed. A systematic study of loading enhancement techniques has been carried out in DIII-D, including reduction of the antenna/plasma distance, gas puffing into the far scrape-off layer (SOL), and control of other parameters that affect the particle balance in the far SOL. Quantitative understanding of the physics of the loading resistance and its dependence on edge density profiles is demonstrated. The core FW heating efficiency appeared to be {approx}100% in the Advanced Inductive regime, consistent with the high first-pass direct electron absorption of {approx}75% that is predicted by the ray-tracing code GENRAY in this high electron beta regime.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

HHFW Heating and Current Drive Studies of NSTX H-Mode Plasmas

30 MHz high-harmonic fast wave (HHFW) heating and current drive are being developed to assist fully non-inductive plasma current (I{sub p}) ramp-up in NSTX. The initial approach to achieving this goal has been to heat I{sub p} = 300 kA inductive plasmas with current drive antenna phasing in order to generate an HHFW H-mode with significant bootstrap and RF-driven current. Recent experiments, using only 1.4 MW of RF power (P{sub RF}), achieved a non-inductive current fraction, f{sub NI}{approx}0.65. Improved antenna conditioning resulted in the generation of I{sub p} = 650 kA HHFW H-mode plasmas, with f{sub NI}{approx}0.35, when P{sub RF}{>=}2.5 MW. These plasmas have little or no edge localized mode (ELM) activity during HHFW heating, a substantial increase in stored energy and a sustained central electron temperature of 5-6 keV. Another focus of NSTX HHFW research is to heat an H-mode generated by 90 keV neutral beam injection (NBI). Improved HHFW coupling to NBI-generated H-modes has resulted in a broad increase in electron temperature profile when HHFW heating is applied. Analysis of a closely matched pair of NBI and HHFW+NBI H-mode plasmas revealed that about half of the antenna power is deposited inside the last closed flux surface (LCFS). Of the power damped inside the LCFS about two-thirds is absorbed directly by electrons and one-third accelerates fast-ions that are mostly promptly lost from the plasma. At longer toroidal launch wavelengths, HHFW+NBI H-mode plasmas can have an RF power flow to the divertor outside the LCFS that significantly reduces RF power deposition to the core. ELMs can also reduce RF power deposition to the core and increase power deposition to the edge. Recent full wave modeling of NSTX HHFW+NBI H-mode plasmas, with the model extended to the vessel wall, predicts a coaxial standing mode between the LCFS and the wall that can have large amplitudes at longer launch wavelengths. These simulation results qualitatively agree with HHFW+NBI H-mode data that show decreasing core RF heating efficiency and increasing RF power flow to the lower divertor at longer launch wavelengths.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Slow Wave Excitation in the ICRF and HHFW Regimes

Theoretical considerations and high spatial resolution numerical simulations of radio frequency (rf) wave heating in tokamaks and in spherical toruses (ST) indicate that fast waves launched into tokamaks in the ion cyclotron range of frequencies (ICRF) or into spherical toruses in the high harmonic fast wave (HHFW) regime may excite a short wavelength slow mode inside of the plasma discharge due to the presence of hot electrons that satisfy the condition {omega}<k{sub ||}v{sub te}, where {omega} is the launched wave frequency, k{sub ||} is the local parallel component of the wave vector, and v{sub te} is the local electron thermal speed. This excited slow wave may be related to the electrostatic ion cyclotron wave that propagates for frequencies above the fundamental ion cyclotron frequency in warm plasmas or to a high frequency version of a kinetic Alfven wave. This slow wave, if physically real, would provide another path for rf power absorption in tokamaks and ST devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Lower hybrid current drive in a high density diverted tokamak

Experimental observations of LHCD at high density (n-bar{sub e}>10{sup 20}m{approx}{sup 3}) on the Alcator C-Mod tokamak are presented in this paper. Bremsstrahlung emission from relativistic fast electrons in the core plasma drops sharply in single null discharges well below the density limit previously observed on limited tokamaks ({omega}/{omega}{sub LH}{approx}2). Modeling and experimental evidence suggest that the absence of LH driven fast electrons at high density may be due to collisional absorption in the scrape off layer. Experiments show that the expected current drive density dependence is recovered for inner wall limited discharges across the range of densities scanned (0.5x10{sup 20} m{sup -3}<n-bar{sub e}<1.5x10{sup 20} m{sup -3}). Increasing T{sub e} in the periphery of the plasma (0.8<r/a<1.0) also results in a modest increase in non-thermal electron emission at high n-bar{sub e}. Ray tracing/Fokker-Planck simulations of these discharges predict the observed sensitivity to plasma position when the effects of collisional absorption in the SOL are included in the model.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Progress in LHCD modeling and experiments towards the AT regime on Alcator C-Mod

Electron internal transport barrier (ITB) formation is observed during fully non-inductive LHCD discharges on Alcator C-Mod. The formation is characterized by an abrupt increase of the central electron temperature after a few current penetration time has passed following LHCD turn-on. The ITB phase is often terminated by m = 2 mode activity. Kinetic equilibrium reconstruction and TRANSP/LSC analysis show shear reversal in the q profile during the ITB phase. TRANSP/LSC predictive analysis suggests that f{sub Bs}{approx}60% is possible if a similar temperature gradient is maintained at r/a{approx}0.5 with H-factor of 1.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observation of Co and Counter Rotation Produced by Lower Hybrid Waves in Alcator C-Mod

Lower hybrid waves launched uni-directionally into tokamak plasmas impart momentum to the electrons. This momentum can be transferred to the ions, leading to substantial counter current rotation. Observations of LH-induced counter rotation have been previously reported [1], and the initial rate of increase has been found to be consistent with the calculated rate of wave momentum injection [2]. However, in recent experiments in Alcator C-Mod it has been found that application of LH waves to relatively low current (I{sub p}{approx}0.4-0.6 MA) plasmas can result in a co-current change of rotation, which implies a different mechanism than that described above. This appears to be linked to the so-called intrinsic rotation commonly observed in Alcator C-Mod and other tokamaks [3]. In addition to the change in direction at low current, some dependence on the magnetic configuration (USL vs. LSN) has been observed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Full wave effects on the lower hybrid wave spectrum and driven current profile in tokamak plasmas

A numerical modeling of current profile modification by lower hybrid current drive (LHCD) using a fullwave/Fokker-Planck simulation code is presented. A MHD stable LHCD discharge on Alcator C-Mod was analyzed, and the current profile from full wave simulations was found to show better agreement with the experiment than a ray-tracing code. Comparison of full wave and ray-tracing simulation shows that, although ray-tracing can reproduce the stochastic wave spectrum broadening, the full wave calculation predicts even wider spectrum broadening, and the wave spectrum fills all of the kinematically allowed domain. This is the first demonstration of LHCD current profile modeling using a full wave simulation code in a multi-pass absorption regime, showing the clear impact of full wave effects on the LHCD driven current profile.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Investigation of lower hybrid physics through power modulation experiments on Alcator C-Mod

Lower hybrid current drive (LHCD) is an attractive tool for off-axis current profile control in magnetically confined tokamak plasmas and burning plasmas (ITER), because of its high current drive efficiency. The LHCD system on Alcator C-Mod operates at 4.6 GHz, with {approx} 1 MW of coupled power, and can produce a wide range of launched parallel refractive index (n) spectra. A 32 chord, perpendicularly viewing hard x-ray camera has been used to measure the spatial and energy distribution of fast electrons generated by lower hybrid (LH) waves. Square-wave modulation of LH power on a time scale much faster than the current relaxation time does not significantly alter the poloidal magnetic field inside the plasma and thus allows for realistic modeling and consistent plasma conditions for different n spectra. Inverted hard x-ray profiles show clear changes in LH-driven fast electron location with differing n. Boxcar binning of hard x-rays during LH power modulation allows for {approx} 1 ms time resolution which is sufficient to resolve the build-up, steady-state, and slowing-down phases of fast electrons. Ray-tracing/Fokker-Planck modeling in combination with a synthetic hard x-ray diagnostic shows quantitative agreement with the x-ray data for high n cases. The time histories of hollow x-ray profiles have been used to measure off-axis fast electron transport in the outer half of the plasma, which is found to be small on a slowing down time scale.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

L-H Threshold Studies in NSTX

Recent experiments in the low aspect ratio National Spherical Torus Experiment (NSTX) have been run in support of the high priority ITER and ITPA issue of access to the H-mode. Specifically, a series of experiments showed reduced power threshold values for deuterium versus helium plasmas, and for plasmas with lower current, lower triangularity and with lithium conditioning. Application of n = 3 fields at the plasma edge resulted in higher power thresholds. To within the constraints of temporal and spatial resolutions, no systematic difference in T(e), n(e), p(e), T(i), v or their derivatives was found in discharges that transitioned into the H-mode versus those at slightly lower power that did not. Finally, H(98y,2) similar to 1 confinement quality could be achieved for powers just above the threshold power in ELM-free conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Absorption of lower hybrid waves in the scrape off layer of a diverted tokamak

The goal of the Lower Hybrid Current Drive (LHCD) system on the Alcator C-Mod tokamak [Hutchinson et al., Phys. Plasmas 1, 1511 (1994)] is to investigate current profile control under plasma conditions relevant to future tokamak experiments. Experimental observations of a LHCD ''density limit'' for C-Mod are presented in this paper. Bremsstrahlung emission from relativistic fast electrons in the core plasma drops suddenly above line averaged densities of 10{sup 20} m{sup -3} ({omega}/{omega}{sub LH{approx}}3-4), well below the density limit previously observed on other experiments ({omega}/{omega}{sub LH{approx}}2). Electric currents flowing through the scrape off layer (SOL) between the inner and outer divertors increase dramatically across the same density range that the core bremsstrahlung emission drops precipitously. These experimental x-ray data are compared to both conventional modeling, which gives poor agreement with experiment above the density limit and a model including collisional absorption in the SOL, which dramatically improves agreement with experiment above the observed density limit. These results show that strong absorption of LH waves in the SOL is possible on a high density tokamak and the SOL must be included in simulations of LHCD at high density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Advances in high-harmonic fast wave physics in the National Spherical Torus Experiment

Improved core high-harmonic fast wave (HHFW) heating at longer wavelengths and during start-up and plasma current ramp-up has now been obtained by lowering the edge density with lithium wall conditioning, thereby moving the critical density for perpendicular fast-wave propagation away from the vessel wall. Lithium conditioning allowed significant HHFW core electron heating of deuterium neutral beam injection (NBI) fuelled H-mode plasmas to be observed for the first time. Large edge localized modes were observed immediately after the termination of rf power. Visible and infrared camera images show that fast wave interactions can deposit considerable rf energy on the outboard divertor. HHFW-generated parametric decay instabilities were observed to heat ions in the plasma edge and may be the cause for a measured drag on edge toroidal rotation during HHFW heating. A significant enhancement in neutron rate and fast-ion profile was measured in NBI-fuelled plasmas when HHFW heating was applied.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Advances in High-harmonic Fast Wave Physics in the National Spherical Torus Experiment

Improved core high-harmonic fast wave (HHFW) heating at longer wavelengths and during start-up and plasma current ramp-up, has now been obtained by lowering the edge density with lithium wall conditioning, thereby moving the critical density for perpendicular fast-wave propagation away from the vessel wall. Lithium conditioning allowed significant HHFW core electron heating of deuterium neutral beam injection (NBI) fuelled H-mode plasmas to be observed for the first time. Large edge localized modes were observed immediately after the termination of rf power. Visible and infrared camera images show that fast wave interactions can deposit considerable rf energy on the outboard divertor. HHFW-generated parametric decay instabilities were observed to heat ions in the plasma edge and may be the cause for a measured drag on edge toroidal rotation during HHFW heating. A significant enhancement in neutron rate and fast-ion profile were measured in NBI-fuelled plasmas when HHFW heating was applied. __________________________________________________

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗