Search NASA⌕ Search

Engineering topics

Winer, W. O.

Publications and source records attributed to Winer, W. O..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Infrared Temperature Measurements of a Reciprocating Seal Test

A system has been developed to perform a computer analysis on surface temperature data in tribological systems, taken by an infrared radiation scanning device. The infrared scanner which normally scans at 25 fields per second and 100 lines per field has been modified to scan any single line at 2500 lines per second. The system was used to analyze four friction experiments as part of a thermal behavior study of Stirling engine seals in cooperation between Georgia Institute of Technology and Mechanical Technology, Incorporated. The friction experiments involved two tribo pairs, Rulon on steel and Rulon on sapphire. The results clearly demonstrate the importance of the relative rate of cooling and the mechanical cycle time of the system. For rapid mechanical cycle times in the friction experiment the surface temperature distribution reflects the distribution of energy input on the surface and the temperatures persist for periods longer than that of the mechanical cycle.

Meinders, M. A.↗
NASA NTRS1982

Surface temperatures and glassy state investigations in tribology, part 5

Preliminary measurements of high shear rate viscosity at near atmospheric but variable pressure suggest the importance of low normal stress and cavitation or fluid fracture in the type of stress field existing in elastohydrodynam ic inlets and classical hydrodynamic configurations. An experimental basis is given for three regimes of traction in concentrated contacts: a thin film regime characterized by high traction and determined by lambda ratio, a thick film regime characterized by low traction and determined by the speed parameter, and the elastohydrodynamic regime for which traction is controlled by limiting shear stress. Traction measurements were performed with various liquids, two solid lubricants, and a grease. Film thickness and traction measurements of polymer blends and base oils are compared.

Bair, S.↗
NASA NTRS1981

Regimes of traction in concentrated contact lubrication

Experimental evidence is presented for the existence of three regimes of traction in concentrated contacts. Data are obtained in a rolling contact simulator by varying the lubricant, temperature, rolling speed, load and surface roughness at a fixed slide-to-roll ratio. At lower thicknesses the mixed regime is encountered, and traction is increased due to asperity interaction, while at higher film thicknesses, the lubricant pressure is distributed over a greater area than the Hertzian region, resulting in a lower average pressure and reduced traction.

Bair, S.↗
NASA NTRS1981

Some observations in high pressure rheology of lubricants

Experimental data are presented on viscosity, elastic shear modulus, and limiting shear stress of 12 liquid lubricants. It is shown that transition histories do affect the limiting shear stress of the materials in the form of isothermal compression resulting in a lower density and lower limiting stress than isobaric cooling. The measured limiting shear stress agrees with EHD traction data at slide-to-roll ratios of 0.1 or more. In pressure viscosity measurements of the polymer solutions, it is found that for some temperatures, the pressure viscosity coefficient of the blend is slightly less than that of the base, which results in the crossing of the viscosity-pressure isotherms at high pressures.

Bair, S.↗
NASA NTRS1981

Preliminary study of temperature measurement techniques for Stirling engine reciprocating seals

Methods of determining the contact surface temperature in reciprocating seals are investigated. Direct infrared measurement of surface temperatures of a rod exiting a loaded cap seal or simulated seal are compared with surface thermocouple measurements. Significant cooling of the surface requires several milliseconds so that exit temperatures may be considered representative of internal contact temperatures.

Wilcock, D. F.↗
NASA NTRS1981

Surface temperatures and glassy state investigations in tribology, part 4

Measurements were made of the limiting shear stress for two naphthenic oils of differing molecular weight and three blends of the lower molecular weight oil and polyalkylmethacrylate polymers of differing molecular weight. The two base oils reached the same limiting shear stress for the same temperature and pressure. This was also true for all the polymer solutions although the polymer reduced the limiting shear stress by about 15 percent. It is shown that limiting stress is more a function of material type than viscosity or molecular weight. A new falling body viscometer was constructed to operate to 230 C and 0.6 GPa. Another viscometer was constructed to extend the pressure range to 1.1 GPa. A concentrated contact simulator was developed which allows recording of the traction force while the slide-roll ratio is continuously varied and the rolling speed is maintained essentially constant by a single drive motor. The configuration is that of a crowned roller against a disk. Measurement of lubricant minimum film thickness of elliptical EHD contacts of various aspect ratios were made by optical interferometry. The data collected were used to evaluate the Hamrock and Dowson minimum film thickness model over a range of contract ellipticity ratio where the major axis of the contact ellipse was aligned both parallel and perpendicular to the direction of motion. A statistical analysis of the measured film thickness data showed that on the average the experimental data were 30 percent greater than the film thickness predicted by the model. Preliminary development of the application of a scanning infrared radiation system to a tribo-system was completed.

Bair, S. S.↗
NASA NTRS1980

A film thickness analysis for line contacts under pure rolling conditions with a non-Newtonian rheological model

The non-Newtonian constitutive equation of Winer and Bair (1979) is applied to a conventional isothermal film thickness analysis of line contact lubrication of rolling elements providing dimensionless film thickness equations for four lubrication methods. The equations can be applied to high viscosity and rolling speed and low limiting shear stress cases where Newtonian methods are not applicable. This analysis is based on a reasonable range of limiting shear stress which is smaller than the Newtonian values for low viscosity lubricants.

Gecim, B.↗
NASA NTRS1980

An experimental evaluation of the Hamrock and Dowson minimum film thickness equation for fully flooded EHD point contacts

Fifty-seven measurements of the minimum lubricant film separating the elastohydrodynamically lubricated point contact of a steel crowned roller and a flat sapphire disk were made by an optical interferometry technique. The data collected were used to evaluate the Hamrock and Dowson minimum EHD film thickness model over a practical range of contact ellipticity ratio where the major axis of the contact ellipse is aligned both parallel and perpendicular to the direction of motion. A statistical analysis of the measured film thickness data showed that on the average the experimental data averaged 30 percent greater film thickness than the Hamrock and Dowson model predicts.

Koye, K. A.↗
NASA NTRS1980

Surface temperatures and glassy state investigations in tribology

Measurements were made of the limiting shear stress for two naphthenic oils of differing molecular weight and three blends of the lower molecular weight oil and polymers of differing molecular weight. All reached the same limiting shear stress for the same temperature and pressure; although the polymer solutions reduced the limiting shear stress by about fifteen percent. A falling body viscometer was constructed to operate to 230 C and to 0.6 GPa and another was constructed to extend the pressure range to 1.1 GPa. A concentrated contact simulator was developed which allows recording of the traction force while the slide-roll ratio is continuously varied and the rolling speed is maintained essentially constant. Measurement of lubricant minimum film thickness of elliptical EHD contacts of various aspect ratios were made by optical interferometry. The experimental data were thirty percent greater than that predicted by the Hamrock and Dowson model. Preliminary development of the application of a scanning infrared radiation system to a tribological system was completed.

Bair, S.↗
NASA NTRS1980

Surface temperatures and glassy state investigations in tribology, part 3

Research related to the development of the limiting shear stress rheological model is reported. Techniques were developed for subjecting lubricants to isothermal compression in order to obtain relevant determinations of the limiting shear stress and elastic shear modulus. The isothermal compression limiting shear stress was found to predict very well the maximum traction for a given lubricant. Small amounts of side slip and twist incorporated in the model were shown to have great influence on the rising portion of the traction curve at low slide-roll ratio. The shear rheological model was also applied to a Grubin-like elastohydrodynamic inlet analysis for predicting film thicknesses when employing the limiting shear stress model material behavior.

Bair, S.↗
NASA NTRS1979

Lubricant limiting shear stress effect on EHD film thickness

A Grubin-like EHD inlet analysis utilizing a non-linear viscous fluid model with a limiting shear stress is reported. The shear rheological equation requirs only a low shear stress viscosity and the limiting shear stress both functions of pressure. Values employed for these properties are taken from measurements on typical lubricants. Reductions of EHD film thickness are found to be up to 40 percent compared with the standard Grubin prediction for typical operating conditions. Slide-roll ratio, limiting shear stress dependence on pressure, and atmospheric pressure value of limiting shear stress are new variables required to determine film thickness with the first two being more important than the last. The EHD film thickness is reduced by increasing slide-roll ratio and/or decreasing the pressure dependence of the limiting shear stress.

Gecim, B.↗
NASA NTRS1979

Some observations on the relationship between lubricant mechanical and dielectric transitions under pressure

Viscoelastic transition measurements of several lubricants by volume dilatometry to pressures of 1.75 GPa, dielectric transitions at atmospheric pressure on five fluids in a frequency range of 0.2 to 500 kHz and on two fluids in the same frequency range to pressures of 0.55 GPa are reported. Lines of constant rate dilatometry transition, constant rate dielectric transition and constant viscosity are shown to be essentially parallel on a temperature-pressure diagram.

Bair, S.↗
NASA NTRS1979

Surface temperatures and glassy state investigations in tribology, part 2

Measurements of lubricant shear rheological behavior in the amorphous solid region and near the liquid solid transition are reported. Elastic, plastic and viscous behavior was observed. The maximum yield shear stress (limiting shear stress) is a function of temperature and pressure and is believed to be the property which determines the maximum traction in elastohydrodynamic contacts such as traction drives. A shear rheological model based on primary laboratory data is proposed for concentrated contact lubrication. The model is Maxwell model modified with a limiting shear stress. Three material properties are required: low shear stress viscosity, limiting elastic shear modulus, and the limiting shear stress the material can withstand. All three are functions of temperature and pressure.

Bair, S. S.↗
NASA NTRS1979

Surface temperatures and glassy state investigations in tribology

The limiting shear stress shear rheological model was applied to property measurements pursuant to the use of the constitutive equation and the application of the constitutive equation to elastrohydrodynamic (EHD) traction. Experimental techniques were developed to subject materials to isothermal compression which is similar to the history the materials were subjected to in EHD contacts. In addition, an apparatus was developed for measuring the shear stress-strain behavior of solid lubricating materials. Four commercially available materials were examined under pressure. They exhibit elastic and limiting shear stress behavior similar to that of liquid lubricants. The application of the limiting shear stress model to traction predictions was extended employing the primary materials properties measured in the laboratory. The shear rheological model was also applied to a Grubin-like EHD inlet analysis for predicting film thicknesses when employing the limiting shear stress model material behavior.

Bair, S.↗
NASA NTRS1979

Shear strength measurements of lubricants at high pressure

Measurements of lubricant shear rheological behavior in the amorphous solid region and near the liquid-solid transition are reported on three lubricants under pressure. Elastic, plastic and viscous behavior was observed. The maximum yield shear stress (limiting shear stress) is a function of temperature and pressure and is believed to be the property which determines the maximum traction in elastohydrodynamic contacts such as traction drives.

Bair, S.↗
NASA NTRS1979

A rheological model for elastohydrodynamic contacts based on primary laboratory data

A shear rheological model based on primary laboratory data is proposed for concentrated contact lubrication. The model is a Maxwell model modified with a limiting shear stress. Three material properties are required: Low shear stress viscosity, limiting elastic shear modulus, and the limiting shear stress the material can withstand. All three are functions of temperature and pressure. In applying the model to EHD contacts the predicted response possesses the characteristics expected from several experiments reported in the literature and, in one specific case where direct comparison could be made, good numerical agreement is shown.

Bair, S.↗
NASA NTRS1978

Investigations of lubricant rheology as applied to elastohydrodynamic lubrication

Measurements of lubricant shear rheological behavior in the amorphous solid region and near the liquid-solid transition are reported. Elastic, plastic and viscous behavior was observed. A shear rheological model based on primary laboratory data is proposed for concentrated contact lubrication. The model is a Maxwell model modified with a limiting shear stress. Three material properties are required: low shear stress viscosity, limiting elastic shear modulus, and the limiting shear stress the material can withstand. All three are functions of temperature and pressure. In applying the model to EHD contacts the predicted response possesses the characteristics expected from several experiments reported in the literature.

Bair, S.↗