Search NASA⌕ Search

Engineering topics

Winsa, E. A.

Publications and source records attributed to Winsa, E. A..

18 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Space flight data from the isothermal dendritic growth experiment

The Isothermal Dendritic Growth Experiment (IDGE) is a NASA space flight experiment which flew as part of the United States Microgravity Payload (USMP-2), in early 1994. The IDGE measured dendritic growth rates, tip radii, and crystal morphologies of ultra-pure succinonitrile (CN-(CH2)2-CN) at supercoolings in the range from 0.05 - 2.0 K. Data taken in the form of slow-scan binary digitized images telemetered to the ground from orbit in near-real time, combined with the IDGE terrestrial data set, provide the first quantitative assessment of various theories on dendritic solidification and the effects of convection on dendritic growth.

Glicksman, M. E.↗
NASA NTRS1994

Dendritic Growth Velocities in Microgravity

We measured dendritic tip velocities in pure succinonitrile (SCN) in microgravity. using a sequence of telemetered binary images sent to Earth from the Space Shuttle Columbia (STS-62). Growth velocities were measured as a function of the supercooling over the range 0.05-1.5 K. Microgravity observations show that buoyancy-induced convection alters the growth kinetics of SCN dendrites at supercooling as high as 1.3 K. Also, the dendrite velocity data measured under microgravity agree well with the Ivantsov paraboloidal diffusion solution when coupled to a scaling constant of sigma(sup *) = 0.0157.

Glicksman, M. E.↗
NASA NTRS1993

IDGE - A test of dendritic growth theory using space flight

The isothermal Dendritic Growth Experiment (IDGE), to be performed on three of the United States Microgravity Payload (USMP) flights, starting with USMP-2, is designed to provide microgravity data on dendritic growth for a critical test of theory. Ground based test data using succinonitrile (SCN), from both a flight growth chamber and a laboratory growth chamber, are compared to theoretical calculations of dendritic tip velocities and radii. The comparison shows that the data from the flight chamber are consistent with the historical data and that dendritic growth in a microgravity environment should exhibit significant differences from the dendritic growth of SCN at g sub 0.

Glicksman, M. E.↗
NASA NTRS1987

Solidification of undercooled Ni-Sn eutectic alloy under microgravity conditions in the Space Shuttle

The Space Shuttle Columbia carried an Alloy Undercooling Experiment on its STS 61-C mission in January, 1986. The experiment was performed in an electromagnetic levitator. A sample of Ni-32.5 wt pct Sn eutectic was melted and solidified under microgravity conditions in the Space Shuttle. The specimen achieved only a fairly small undercooling, probably less than 30 K. The specimen was examined by optical and scanning electron microscopy. The surface and cross-sectional microstructures were primarily composed of normal lamellar eutectic, but showed several interesting features, including an apparent surface nucleation site, curved dendrites with nonorthogonal secondary arms, dendrite fragments with extremely fine arm spacing, submicron precipitates, and faceted crystals. The results of the space experiment are presented and compared with ground-based results obtained with the same alloy.

Piccone, T. J.↗
NASA NTRS1987

Gravitational macrosegregation in binary Pb-Sn alloy ingots

A space shuttle experiment employing the General Purpose (Rocket) Furnace (GPF) in its isothermal mode of operation is manifested on MSL-3, circa 1989. The central aim of this experiment is to investigate the effect of reduced gravity levels on the segregation behavior in a slowly, and isothermally, cooled sample of a binary Pb-15 wt pct Sn alloy. This experiment should be able to simulate, in a small laboratory sample, some aspects of the segregation phenomena occurring in large industrial ingots. Ground-based experiments conducted in the single-cavity simulator of the GPF, in support of the microgravity experiment are described in detail. The results of the MSFC experiments are compared with other related experiments conducted at Case Western Reserve University (CWRS), wherein the isothermal constraints were relaxed. The isothermally processed samples indicate a small and gradual increase in fraction eutectic, and a corresponding increase in tin content, from the bottom to the top of the ingot. The radial variations are minimal near the ingot bottom, but there are large radial variations in the top half. In the CWRU experiments, more severe segregations, including segregation defects known as freckles. Follow up experiments employing the GPF without the isothermal constraints, or other suitably modified space shuttle hardware are suggested.

Laxmanan, V.↗
NASA NTRS1986

Gravitational macrosegregation in binary Pb-Sn alloy ingots

A space shuttle experiment employing the General Purpose (Rocket) Furnace (GPF) in its isothermal mode of operation is manifested on MSL-3, circa 1989. The central aim of this experiment is to investigate the effect of reduced gravity levels on the segregation behavior in a slowly, and isothermally, cooled sample of a binary Pb-15 wt% Sn alloy. This experiment should be able to simulate, in a small laboratory sample, some aspects of the segragation phenomena occurring in large industrial ingots. Ground-based experiments conducted in the single-cavity simulator of the GPF, in support of the microgravity experiment are described in detail. The results of the MSFC experiments are compared with other related experiments conducted at Case Western Reserve University (CWRS), wherein the isothermal constraints were relaxed. The isothermally processed samples indicate a small and gradual increase in fraction eutectic, and a corresponding increase in tin content, from the bottom to the top of the ingot. The radial variations are minimal near the ingot bottom, but there are large radial variations in the top half. In the CWRU experiments, more severe segregations, including segregation defects known as freckles. Follow up experiments employing the GPF without the isothermal constraints, or other suitably modified space shuttle hardware are suggested.

Laxmanan, V.↗
NASA NTRS1983

Tungsten-fiber-reinforced superalloy composite, high-temperature component design considerations

Tungsten fiber reinforced superalloy composites (TFRS) are intended for use in high temperature turbine components. Current turbine component design methodology is based on applying the experience, sometimes semiempirical, gained from over 30 years of superalloy component design. Current composite component design capability is generally limited to the methodology for low temperature resin matrix composites. Often the tendency is to treat TFRS as just another superalloy or low temperature composite. However, TFRS behavior is significantly different than that of superalloys, and the high environment adds consideration not common in low temperature composite component design. The methodology used for preliminary design of TFRS components are described. Considerations unique to TFRS are emphasized. Previously announced in STAR as N82-21259

Winsa, E. A.↗
NASA NTRS1982

Tungsten fiber reinforced superalloy composite high temperature component design considerations

Tungsten fiber reinforced superalloy composites (TFRS) are intended for use in high temperature turbine components. Current turbine component design methodology is based on applying the experience, sometimes semiempirical, gained from over 30 years of superalloy component design. Current composite component design capability is generally limited to the methodology for low temperature resin matrix composites. Often the tendency is to treat TFRS as just another superalloy or low temperature composite. However, TFRS behavior is significantly different than that of superalloys, and the high environment adds consideration not common in low temperature composite component design. The methodology used for preliminary design of TFRS components are described. Considerations unique to TFRS are emphasized.

Winsa, E. A.↗
NASA NTRS1979

Thermal-conductivity measurements of tungsten-fiber-reinforced superalloy composites using a thermal-conductivity comparator

The thermal conductivity (TC) of tungsten-fiber-reinforced superalloys was determined for two composite systems by using a thermal conductivity standard from the National Bureau of Standards and a comparator and technique developed for that purpose. The results were compared with TC data for the nickel-base alloy MAR-M200. The technique lends itself to applications involving thin specimens, such as thin-walled turbine blades. The TC's of the composite systems were considerably higher in both the longitudinal and transverse directions than that of the monolithic superalloys used as the matrices.

Westfall, L. J.↗
NASA NTRS1979

Tungsten fiber reinforced FeCrAlY - A first generation composite turbine blade material

General and composite turbine blade material requirements are examined to identify a specific tungsten fiber reinforced superalloy (TFRS) having, in addition to strength, the desired combination of other material properties needed in turbine blades. Experimental data indicated that a thoriated tungsten fiber reinforced FeCrAlY matrix composite should have the stress-rupture, creep, tensile, fatigue, and impact strengths required for turbine blades operating from 1250 to 1370 K. Fabrication and design concepts are developed to demonstrate the feasibility of fabricating a hollow TFRS turbine blade at reasonable cost.

Petrasek, D. W.↗
NASA NTRS1979

Tungsten fiber reinforced FeCralY: A first generation composite turbine blade material

Tungsten-fiber/FeCrAlY (W/FeCrAlY) was identified as a promising aircraft engine, first generation, turbine blade composite material. Based on available data, W/FeCrAlY should have the stress-rupture, creep, tensile, fatigue, and impact strengths required for turbine blades operating from 1250 to 1370 K. It should also have adequate oxidation, hot corrosion, and thermal cycling damage resistance as well as high thermal conductivity. Concepts for potentially low cost blade fabrication were developed. These concepts were used to design a first stage JT9D convection cooled turbine blade having a calculated 50 K use-temperature advantage over the directionally solidified superalloy blade.

Petrasek, D. W.↗
NASA NTRS1978

Predicted inlet gas temperatures for tungsten fiber reinforced superalloy turbine blades

Tungsten fiber-reinforced superalloy composite (TFRS) impingement-cooled turbine blade inlet gas temperatures were calculated taking into account material spanwise strength, thermal conductivity, material oxidation resistance, fiber-matrix interaction, and coolant flow. Measured values of TFRS thermal conductivities are presented. Calculations indicate that blades made of 30 volume percent fiber content TFRS having a 12,000 N-m/kg stress-to-density ratio while operating at 40 atm and a 0.06 coolant flow ratio could permit a turbine blade inlet gas temperature of over 1900 K. This is more than 150 K greater than similar superalloy blades.

Winsa, E. A.↗
NASA NTRS1978

Predicted inlet gas temperatures for tungsten fiber reinforced superalloy turbine blades

Tungsten fiber reinforced superalloy composite (TFRS) impingement cooled turbine blade inlet gas temperatures were calculated taking into account material spanwise strength, thermal conductivity, material oxidation resistance, fiber-matrix interaction, and coolant flow. Measured values of TFRS thermal conductivities are presented. Calculations indicate that blades made of 30 volume percent fiber content TFRS having a 12,000 N-m/kg stress-to-density ratio while operating at 40 atmospheres and a 0.06 coolant flow ratio could permit a turbine blade inlet gas temperature of over 1900K. This is more than 150K greater than similar superalloy blades.

Winsa, E. A.↗
NASA NTRS1978

Predicted inlet gas temperatures for tungsten fiber reinforced superalloy turbine blades

A procedure is presented for predicting the magnitude of the turbine inlet gas temperatures potentially achievable using first generation tungsten fiber reinforced superalloys (TFRS) turbine blades. Both uncoated blades and blades with thermal barrier coatings are considered. The thermal conductivities of two representative TFRS were measured over a range of temperatures. The results show that cooled TFRS blades may allow significantly higher gas temperatures than are possible with superalloy blades. For one design, the difference is about 150-200 K.

Winsa, E. A.↗
NASA NTRS1973

Factors affecting miniature Izod impact strength of tungsten-fiber-metal-matrix

The miniature Izod and Charpy impact strengths of copper, copper-nickel, and nickel-base superalloy uniaxially reinforced with continuous tungsten fibers were studied. In most cases, impact strength was increased by increasing fiber or matrix toughness, decreasing fibermatrix reaction, increasing test temperature, hot working, or heat treating. Notch sensitivity was reduced by increasing fiber content or matrix toughness. An equation relating impact strength to fiber and matrix properties and fiber content was developed. Program results imply that tungsten alloy-fiber/superalloy matrix composites can be made with adequate impact resistance for turbine blade or vane applications.

Winsa, E. A.↗
NASA NTRS1972

Pendulum impact resistance of tungsten fiber/metal matrix composites.

The impact properties of copper, copper-10 nickel, and a superalloy matrix reinforced with tungsten fibers were studied. In most cases the following increased composite impact strength: increased fiber or matrix toughness, decreased fiber-matrix reaction, increased test temperature, hot working and heat treatment. Notch sensitivity was reduced by increasing fiber or matrix toughness. The effect of fiber content depended on the relative toughness of the fibers and matrix. Above 530 K a 60 volume per cent superalloy matrix composite had a greater impact strength than a turbine blade superalloy, whereas below 530 K a hot worked 56 volume per cent composite had a greater impact strength than the superalloy.

Winsa, E. A.↗