Search NASASearch

Engineering topics

Winter, J. M.

Publications and source records attributed to Winter, J. M..

The Agricultural Model Intercomparison and Improvement Project (AgMIP): Protocols and Pilot Studies

The Agricultural Model Intercomparison and Improvement Project (AgMIP) is a major international effort linking the climate, crop, and economic modeling communities with cutting-edge information technology to produce improved crop and economic models and the next generation of climate impact projections for the agricultural sector. The goals of AgMIP are to improve substantially the characterization of world food security due to climate change and to enhance adaptation capacity in both developing and developed countries. Analyses of the agricultural impacts of climate variability and change require a transdisciplinary effort to consistently link state-of-the-art climate scenarios to crop and economic models. Crop model outputs are aggregated as inputs to regional and global economic models to determine regional vulnerabilities, changes in comparative advantage, price effects, and potential adaptation strategies in the agricultural sector. Climate, Crop Modeling, Economics, and Information Technology Team Protocols are presented to guide coordinated climate, crop modeling, economics, and information technology research activities around the world, along with AgMIP Cross-Cutting Themes that address uncertainty, aggregation and scaling, and the development of Representative Agricultural Pathways (RAPs) to enable testing of climate change adaptations in the context of other regional and global trends. The organization of research activities by geographic region and specific crops is described, along with project milestones. Pilot results demonstrate AgMIP's role in assessing climate impacts with explicit representation of uncertainties in climate scenarios and simulations using crop and economic models. An intercomparison of wheat model simulations near Obregón, Mexico reveals inter-model differences in yield sensitivity to [CO2] with model uncertainty holding approximately steady as concentrations rise, while uncertainty related to choice of crop model increases with rising temperatures. Wheat model simulations with midcentury climate scenarios project a slight decline in absolute yields that is more sensitive to selection of crop model than to global climate model, emissions scenario, or climate scenario downscaling method. A comparison of regional and national-scale economic simulations finds a large sensitivity of projected yield changes to the simulations' resolved scales. Finally, a global economic model intercomparison example demonstrates that improvements in the understanding of agriculture futures arise from integration of the range of uncertainty in crop, climate, and economic modeling results in multi-model assessments.

Rosenzweig, C.

Extended SP-100 reactor power systems capability

The SP-100 space nuclear power system development program and the NASA Civil Space Technology Initiative (CSTI) are discussed. The advanced technologies being developed for the CSTI high capacity nuclear reactor power system are outlined. The relationship between the CSTI and the Pathfinder project is considered.

Bloomfield, H. S.

Experimental performance of the regenerator for the Chrysler upgraded automotive gas turbine engine

Automobile gas turbine engine regenerator performance was studied in a regenerator test facility that provided a satisfactory simulation of the actual engine operating environment but with independent control of airflow and gas flow. Velocity and temperature distributions were measured immediately downstream of both the core high-pressure-side outlet and the core low-pressure-side outlet. For the original engine housing, the regenerator temperature effectiveness was 1 to 2 percent higher than the design value, and the heat transfer effectiveness was 2 to 4 percent lower than the design value over the range of test conditions simulating 50 to 100 percent of gas generator speed. Recalculating the design values to account for seal leakage decreased the design heat transfer effectiveness to values consistent with those measured herein. A baffle installed in the engine housing high-pressure-side inlet provided more uniform velocities out of the regenerator but did not improve the effectiveness. A housing designed to provide more uniform axial flow to the regenerator was also tested. Although temperature uniformity was improved, the effectiveness values were not improved. Neither did 50-percent flow blockage (90 degree segment) applied to the high-pressure-side inlet change the effectiveness significantly.

Winter, J. M.

Comparative analysis of the conceptual design studies of potential early commercial MHD power plants (CSPEC)

A conceptual design study of the MHD/steam plant that incorporates the use of oxygen enriched air preheated in a metallic heat exchanger as the combustor oxidant showed that this plant is the most attractive for early commercial applications. The variation of performance and cost was investigated as a function of plant size. The contractors' results for the overall efficiencies are in reasonable agreement considering the slight differences in their plant designs. NASA LeRC is reviewing cost and performance results for consistency with those of previous studies, including studies of conventional steam plants. LeRC in house efforts show that there are still many tradeoffs to be considered for these oxygen enriched plants and considerable variations can be made in channel length and level of oxygen enrichment with little change in overall plant efficiency.

Sovie, R. J.

Design and evaluation of an oxidant-fuel-ratio-zoned rocket injector for high performance and ablative engine compatibility

A method for temperature control of the combustion gases in the peripheral zone of a rocket combustor which would reduce ablative throat erosion, prevent melting of zirconia throat inserts, and maintain high combustion performance is discussed. Included are techniques for analyzing and predicting zoned injector performance, as well as the philosophy and method for accomplishing an optimum compromise between high performance and reduced effective gas temperature. The experimental work was done with a 1000-lbf rocket engine which used as propellants N2O4 and a blend of 50-percent N2H4 and 50-percent UDMH at 100-psia chamber pressure and an overall O/F of 2.0. The method selected to provide temperature control was to use 30 percent of the propellant to form a peripheral zone of combustion gases at an O/F of 1.31 and 2700 K. The remaining 70 percent of the propellant in the core was at an O/F of 2.45 to keep the overall O/F at 2.0.

Winter, J. M.

High-temperature oxidation and erosion-resistant refractory coatings

Various refractory coating systems were evaluated for rocket nozzle applications by actual rocket test firings. A reference is noted which identifies failure mechanisms and gives results of the firing tests for 18 coating systems. Iridium, iridium-rhenium, and hafnium oxide-zirconium oxide coatings show most promising results.

Peterson, D. A.