Engineering topics

Witold Koning

Publications and source records attributed to Witold Koning.

6 records

NASA NTRS2023

Structural Design and Aeromechanical Analysis of Unconventional Blades for Future Mars Rotorcraft

The structural design for rotor blades with thin, unconventional airfoils for Earth-based testing is obtained using three-Dimensional (3D) aeromechanical analysis in support of the NASA ROAMX project. The outer mold line was provided by NASA, but the internal structural design was developed at the University of Maryland and is presented here along with a thorough aeromechanical analysis. The main objectives are to verify the structural integrity of the design and understand the unique aeroelastic behavior of the non-conventional airfoils designed for low-Reynolds number and high subsonic Mach number. Four different blade models are considered, with the pitch axis varied from quarter-chord to mid-chord to determine the effect of C.G. offset on natural frequencies, blade deformations, root loads, and 3D stresses. First, torsional stability is calculated for each of the designs – especially important due to the low Lock number on Mars. All four blade designs are studied under rotation in vacuum, and significant reductions in root loads and 3D stresses are achieved by moving the pitch axis closer to mid-chord to reduce the C.G. offset. Based on the vacuum analysis, the blade design with the pitch axis at 40% chord is selected for aeromechanical analysis. The blade control load, airloads, deformations, and 3D stresses are studied for steady hover. Dynamic control load and dynamic 3D stresses are studied for unsteady hover achieved using cyclic. Significant elastic twist is observed due to the trapeze effect and propeller moment, affecting the spanwise distribution of aerodynamic loads on the blades. The dynamic control load is found to increase significantly due to inertial coupling from the C.G. offset. The dynamic stresses also increase, although still have factors of safety greater than two for both tensile and compressive stress.

Structural Design↗

NASA NTRSDate not supplied

Comparing RotCFD Predictions of the Multirotor Test Bed with Experimental Results

The Multirotor Test Bed (MTB) is a new capability for testing a wide array of advanced vertical take-off and landing (VTOL) rotor configurations, with a primary focus on testing in the U.S. Army 7- by 10-ft Wind Tunnel at NASA Ames Research Center. The MTB was designed to allow adjustment of the vertical, lateral, and longitudinal placement of each rotor, as well as allow tilt adjustment of each rotor and pitch adjustment of the whole assembly. Each rotor can tilt forward 90 deg and backwards 5 deg. In addition, the entire MTB can tilt forward 20 deg and backwards 10 deg. This flexibility allows the system to be tested in many different configurations. There is a six-axis load cell under each rotor assembly, to measure both the steady and dynamic loads produced by each rotor. The wind tunnel scales can measure loads on the full assembly. The overall goal of the MTB project is to help gain a better understanding of the performance, control, interactional aerodynamics, and acoustics of multirotor systems. A hybrid CFD tool called RotCFD (Rotorcraft Computational Fluid Dynamics) was used to simulate the MTB in several testing configurations. This paper explains the method of running the RotCFD simulations and explores the results from the simulations. The objective of this paper is to compare the RotCFD simulation results with the MTB wind tunnel test data, seeking to further validate RotCFD for multirotor systems and assess the influence of aerodynamic interactions on individual rotor performance.

RotCFD↗

NASA NTRSDate not supplied

Mars Science Helicopter: Conceptual Design of the Next Generation of Mars Rotorcraft

Robotic planetary aerial vehicles increase the range of terrain that can be examined, compared to traditional landers and rovers, and have more near-surface capability than orbiters. Aerial mobility is a promising possibility for planetary exploration as it reduces the challenges that difficult obstacles pose to ground vehicles. The first use of a rotorcraft for a planetary mission will be in 2021, when the Ingenuity Mars helicopter technology demonstrator will be deployed via the Perseverance rover. NASA’s Jet Propulsion Laboratory and NASA Ames Research Center are exploring possibilities for a Mars Science Helicopter, a second-generation Mars rotorcraft with the capability of conducting science investigations independently of a lander or rover (although this type of vehicle could also be used to assist rovers or landers in future missions). Two, large rotorcraft configurations are described: a hexacopter and a co-axial helicopter with a payload in the range of two to three kilograms and an overall vehicle mass of approximately twenty kilograms. Additionally, advancements in technology over the course of the study are applied to a rotorcraft of the same size and form as Ingenuity. Initial estimates of weight and performance were based on the capabilities of Ingenuity. Rotorcraft designs for Mars are constrained by the dimensions of the aeroshell and lander for the trip to the planet, constraining maximum rotor dimensions and, hence, overall performance potential. The effects of airfoils designed specifically for the low Reynolds number and high Mach number inherent to operation on Mars were studied. Rotor structural designs were developed that met blade frequency and weight targets, subject to material stress limits. The final designs are representative of the vehicle configurations required for a large range of future missions and will require relatively minor adaptations once science tasks are chosen. These designs will be compared to Ingenuity to demonstrate technology advancements developed during the study.

Mars Science Helicopter↗

NASA NTRSDate not supplied

Overview and Introduction of the Rotor Optimization for the Advancement of Mars eXploration (ROAMX) Project

Research in pursuit of rotorcraft flight on Mars has been ongoing since the late 1990s at NASA Ames Research Center. Since then, many other organizations have also begun researching rotary-wing flight on Mars. In 2014, the project that led to the first helicopter to fly on Mars began at the Jet Propulsion Laboratory. Ingenuity was developed as a joint effort between JPL, NASA Ames, NASA Langley, and AeroVironment. The Ingenuity Mars Helicopter made history in April 2021 as the first vehicle demonstrating controlled, powered flight on another planet and, in doing so, it has opened a new era of planetary aviation. Future, more capable Mars rotorcraft will be able to fly even further and carry significant science payload. At NASA Ames, through NASA Space Technology Mission Directorate funding, the research necessary to help develop the next generation of Mars rotorcraft has begun with the Rotor Optimization for the Advancement of Mars eXploration (ROAMX) project. The ROAMX project involves computationally and experimentally investigating aerodynamically efficient, compressible, low-Reynolds number airfoils for rotor blades and, further, new high-performance rotor designs. ROAMX is also developing and validating a rotor design methodology to optimize blades given specific mission requirements. The primary experimental effort of the ROAMX project is focused on rotor hover performance, but subsequent airfoil and rotor design advances are anticipated to carry over into improvements in forward flight efficiency. ROAMX is a collaboration between NASA Ames, JPL, the University of Maryland, AeroVironment, and Tohoku University.

Rotor Optimization for the Advancement of Mars eXp↗

NASA NTRSDate not supplied

Structural Design and Aeromechanical Analysis of Unconventional Blades for Future Mars Rotorcraft

The structural design for rotor blades with thin, unconventional airfoils for Earth-based testing is obtained using three-Dimensional (3D) aeromechanical analysis. This analysis is in support of the NASA ROAMX project. The outer mold was provided by NASA, but the internal structural design was developed at the University of Maryland and is presented here, along with a thorough aeromechanical analysis. The main objectives are to verify the structural integrity of the design and understand the unique aeroelastic behavior of the non-conventional airfoils designed for low-Reynolds number and high-Mach number flow. Six different blade models are considered, with the pitch axis varied from quarter-chord to mid-chord to determine the effect of C.G. offset on natural frequencies, blade deformations, root loads, and 3D stresses. All six blade designs are first studied under rotation in pure vacuum, and significant reductions in root loads and 3D stresses are achieved by moving the pitch axis closer to mid-chord to reduce the C.G. offset. Based on the vacuum analysis, the blade design with the pitch axis at 40% chord is selected for aerodynamic analysis. The blade control load, airloads, deformations, and 3D stresses are studied for steady hover. Dynamic control load and dynamic 3D stresses are studied for unsteady hover achieved using cyclic. Significant elastic twist is observed due to the trapeze effect and propeller moment, affecting the spanwise distribution of aerodynamic loads on the blades. However, the effect of aerodynamic loads on 3D stresses and the blade control load is found to be minimum. The dynamic control load is found to increase significantly due to inertial coupling from the C.G. offset. The dynamic stresses also increase, although still have factors of safety greater than two for both tensile and compressive stress.

Structural Design↗

NASA NTRSDate not supplied

Mars Sample Recovery Helicopter: Rotorcraft to Retrieve the First Samples from the Martian Surface

The Mars Sample Return Mission (MSR) will carry the next set of Mars helicopters, Sample Recovery Helicopters (SRHs), to the Martian surface. After successfully demonstrating extraterrestrial flight in 2021, Ingenuity has acted as a “scout” for the Perseverance rover while the rover gathers samples of Martian soil. In 2028, the MSR mission will launch a lander and two Ingenuity-sized SRHs to retrieve these samples. These will be the first samples of the Martian surface delivered to Earth. The SRH project will maintain heritage from Ingenuity’s design when possible. However, several key changes must be made, including a ground mobility system, a robotic arm for tube manipulation, and the ability to carry the weight of a science payload (the sample tubes). In addition, the onboard software and cameras will be upgraded, and the rotor radius will be increased. Furthermore, new rotor performance and flight dynamics models and thorough characterization of vehicle limits will be required. The new vehicle design will be described, as well as validation and verification efforts to date.

Rotorcraft↗