Engineering topics
Publications and source records attributed to Wolfe, W. L..
An instrument is described that has been used to measure the spatial and temporal distributions of lightning strokes as seen from a high-altitude aircraft platform. It consists of two separate sensors. One has a lens, selectable filters, and a 50 x 50 element array of photodiodes. The second has an identical lens, filters, and a single detector that covers the same total field of view.
Two comparisons of available specular infrared measurements using identical or very similar coatings reveal that specular BRDF (bidirectional reflectance distribution function) measurements of rough coatings are comparable but that simple measured reflectances are not. This is seen as indicating that the diffuse component of the measured specular reflectance is significantly larger than that of the specular component. It is noted that the diffuse component of the measurement is a convolution of the intrinsic directional reflectivity of the surface with the instrument function and that because the value of that function increases at the wavelengths under consideration, the diffuse component is larger than would otherwise be expected. The BRDF normalization is found to cause a primitive deconvolution of the instrument function and to produce a quantity that is approximately equal to the mean intrinsic directional reflectivity very near the specular direction. The analysis and comparison of data reveal that nonspecular BRDF measurements at angles well outside the instrument function can be calibrated as well by an image of the source upon the detector as by reference to a known surface.
The Infrared Astronomical Satellite (IRAS) telescope has an outer shield on it which is used to reduce the amount of thermal radiation that enters the telescope. The shield forms the first part of the baffle structure which reduces the photon incidence on the focal plane. It was, therefore, necessary to model this structure for scattering, and a required input for such modeling is the scattering characteristic of this surface. Attention is given to the measurement of the bidirectional reflectance distribution function (BRDF), the reflected radiance divided by the incident irradiance at 10.6 micrometers, 118 micrometers, and at several angles of incidence. Visual observation of the gold sample shows that there are striations which line up in a single direction. The data were, therefore, taken with the sample oriented in each of two directions.
The BRDF values of several samples of Martin Black have been measured at 10.6 microns and several angles of incidence. The values are in good agreement with data taken recently on an identical sample with a different instrument and with data from an identical sample taken several years ago with a similar instrument.
BRDF (bidirectional reflectance distribution function) values for 0.000118 m radiation at different angles of incidence and different scattering angles from the Infrared Astronomical Satellite telescope baffle coated with Martin Black are presented. Data from scatterometer experiments are collected and the BRDF and beta - beta sub 0 (sin theta sub s - sin theta sub 0) values are calculated based on the geometry, the voltage readings, the attenuators in the beam, and the calculated reference levels. A composite curve of forward and backward scattering data for several angles of incidence shows a peak near the specular direction (beta - beta sub 0 = 0), which is the instrument profile reduced by the 20% specular reflection of the Martin Black. The nonspecular part of the reflectivity indicates the slightly specular but largely Lambertian character of the coating. Data for the specular reflectivity as a function of the incidence angle unexpectedly shows a decrease in the specular reflectance with increasing angle of incidence.
The Solar Flux Radiometer aboard the Pioneer Venus Sounder Probe operated successfully during its descent through the atmosphere of Venus. The instrument measured atmospheric radiance over the spectral range from 400 to 1800 nm as a function of altitude. Elevation and azimuthal measurements on the radiation field were made with five optical channels. Twelve filtered Si and Ge photovoltaic detectors were maintained near 30 C with a phase-change material. The detector output currents were processed with logarithmic transimpedance converters and digitized with an 11-bit A/D converter. Atmospheric sampling in both elevation and azimuth was done according to a Gaussian integration scheme. The serial output data averaged 20 bits/sec, including housekeeping (sync, spin period, sample timing and mode). The data were used to determine the deposition of solar energy in the atmosphere of Venus between 67 km and the surface along with upward and downward fluxes and radiances with an altitude resolution of several hundred meters. The results allow for more accurate modeling of the radiation balance of the atmosphere than previously possible.
A conceptual design of a broad-area optical lightning telescope sensor (BOLTS) designed to provide full-time (day/night) coverage of the continental United States from a geosynchronous orbit is described. Variations are discussed that could cover the whole globe from four to five geosynchronous satellites or cover only smaller areas with a high (2.5 km) resolution. The design is based on research results of the initial phase of a NASA-sponsored program. The ground resolution will be 8 x 8 km. The focal plane is an 800 x 800 pixel CCD array, electronically subdivided to allow for the high data rates (1000 frames per sec) imposed by the characteristics of lightning flashes. It will detect lightning strokes whose optical power is greater than 10 million watts, with a probability of detection of 0.9, and a false alarm rate of 0.1.
The described instrument is to measure the net solar radiation as a function of altitude as the probe descends through the Venus atmosphere. The data are to provide a basis for the study of the mechanisms which are responsible for the high surface temperature of the planet Venus. The instrument consists of two separate sections, including an optical head and an electronics package. The radiance is measured with silicon and indium arsenide detectors. Details of radiometer design are discussed along with the characteristics of the optical system and the detectors. Angular and radiometric calibration procedures are also considered.
Measurement of total normal emittance of nuclear reactor materials - carbon steel, boron steel, & borated graphite