Search NASA⌕ Search

Engineering topics

Wong, G. S.

Publications and source records attributed to Wong, G. S..

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Extreme Ultraviolet Explorer Science Operation Center

The EUVE Science Operations Center (ESOC) is a satellite payload operations center for the Extreme Ultraviolet Explorer project, located on the Berkeley campus of the University of California. The ESOC has the primary responsibility for commanding the EUVE telescopes and monitoring their telemetry. The ESOC is one of a very few university-based satellite operations facilities operating with NASA. This article describes the history, operation, and advantages of the ESOC as an on-campus operations center.

Wong, G. S.↗
NASA NTRS1993

Active control of wing rock of a delta wing at post-stall using tangential leading edge blowing

Post-stall roll control utilizing tangential leading edge blowing is demonstrated in a wind tunnel on a delta wing model that exhibited wing rock. The dampening effect of symmetric blowing alone on wing rock is found to be effective up to a certain maximum amount of blowing. A moderate amount of symmetric blowing was shown to be effective in linearizing the asymmetric blowing static rolling moment responses.

Wong, G. S.↗
NASA NTRS1991

Operationally Efficient Propulsion System Study (OEPPS)

A description is presented, through view graphs, of the problems encountered in today's launch vehicles and how these problems have adversely affected the ability to achieve serviceability, reliability, and operability. The need is emphasized to recognize and understand the operations problems and the effort that must be made to avoid them in future designs. Technology areas that will enhance operations requirements are also presented.

Wong, G. S.↗
NASA NTRS1977

Rocketdyne's advanced coal slurry pumping program

The Rocketdyne Division of Rockwell International Corporation is conducting a program for the engineering, fabrication, and testing of an experimental/prototype high-capacity, high-pressure centrifugal slurry feed pump for coal liquefaction purposes. The abrasion problems in a centrifugal slurry pump are primarily due to the manner in which the hard, solid particles contained in the slurry are transported through the hydraulic flow passages within the pump. The abrasive particles can create scraping, grinding, cutting, and sandblasting effects on the various exposed parts of the pump. These critical areas involving abrasion and impact erosion wear problems in a centrifugal pump are being addressed by Rocketdyne. The mechanisms of abrasion and erosion are being studied through hydrodynamic analysis, materials evaluation, and advanced design concepts.

Davis, D. E.↗
NASA NTRS1973

Liquid hydrogen turbopump rapid start program

This program was to analyze, test, and evaluate methods of achieving rapid-start of a liquid hydrogen feed system (inlet duct and turbopump) using a minimum of thermal preconditioning time and propellant. The program was divided into four tasks. Task 1 includes analytical studies of the testing conducted in the other three tasks. Task 2 describes the results from laboratory testing of coating samples and the successful adherence of a KX-635 coating to the internal surfaces of the feed system tested in Task 4. Task 3 presents results of testing an uncoated feed system. Tank pressure was varied to determine the effect of flowrate on preconditioning. The discharge volume and the discharge pressure which initiates opening of the discharge valve were varied to determine the effect on deadhead (no through-flow) start transients. Task 4 describes results of testing a similar, internally coated feed system and illustrates the savings in preconditioning time and propellant resulting from the coatings.

Wong, G. S.↗
NASA NTRS1973

Liquid hydrogen turbopump rapid start program

Effort was directed toward the completion of the coated feed system testing and data analysis of both the uncoated and coated system tests. A total of 11 tests were conducted with the coated feed system during three days of testing. Chill data was acquired for thermal conditioning of the system from ambient initial conditions, using a duct inlet propellent pressure of 72 psig. After three tests to determine steady state pump performance and nominal start transient operation, three coated system turbopump starts were attempted with various degrees of prechill.

Wong, G. S.↗