Search NASA⌕ Search

Engineering topics

Wood, R. M.

Publications and source records attributed to Wood, R. M..

27 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Assessment of preliminary prediction techniques for wing leading-edge vortex flows at supersonic speeds

The applicability of existing theoretical models for predicting wing leading edge separated flow characteristics for high-lift supersonic flight was examined with regard to previous experimental force, pressure and flow visualization data. Correlations of data on uncambered delta wings revealed that the upper surface normal force and minimum pressure coefficients decreased nonlinearly with increasing angles of attack. The attainable vacuum pressure decreased with increasing Mach number, while the lower surface normal force increased nonlinearly with increasing speed. The LISTAR and VORCAM linear theory aerodynamic codes generated predictions for comparison with the data. LISTAR displayed better agreement with measured vortex strength and position and lifting characteristics than did VORCAM. The Euler code SWINT was ill-suited to calculating wing performance in separated flows at high lift and low supersonic speeds.

Wood, R. M.↗
NASA NTRS1984

Effect of fuselage upwash on the supersonic longitudinal aerodynamic characteristics of 2 fighter configurations

An experimental and theoretical investigation of fuselage incidence effects on two fighter aircraft models, which differed in wing planform only, has been conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.6, 1.8, and 2.0. Results were obtained on the two models at fuselage incidence angles of 0 deg, 2 deg, and 5 deg. The fuselage geometry included two side-mounted, flow-through, half-axisymmetric inlets and twin vertical tails. The two planforms tested were cranked wings with 70 deg/66 deg and 70 deg/30 deg leading-edge sweep angles. Experimental data showed that fuselage incidence resulted in positive increments in configuration lift and pitching moment; most of the lift increment can be attributed to the fuselage-induced upwash acting on the wing and most of the pitching-moment increment is due to the fuselage. Theoretical analysis indicates that linear-theory methods can adequately predict the overall configuration forces and moments resulting from fuselage upwash, but a higher order surface-panel method (PAN AIR) more accurately predicted the distribution of forces and resulting moments between the components.

Wood, R. M.↗
NASA NTRS1984

Wing planform effects at supersonic speeds for an advanced fighter configuration

Four advanced fighter configurations, which differed in wing planform and airfoil shape, were investigated in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.80, 2.00, and 2.16. Supersonic data were obtained on the four uncambered wings, which were each attached to a single fighter fuselage. The fuselage geometry varied in cross-sectional shape and had two side-mounted, flow-through, half-axisymmetric inlets. Twin vertical tails were attached to the fuselage. The four planforms tested were a 65 deg delta wing, a combination of a 20 deg trapezoidal wing and a 45 deg horizontal tail, a 70 deg/30 deg cranked wing, and a 70 deg/66 deg crank wing, where the angle values refer to the leading-edge sweep angle of the lifting-surface planform. Planform effects on a single fuselage representative of an advanced fighter aircraft were studied. Results show that the highly swept cranked wings exceeded the aerodynamic performance levels, at low lift coefficients, of the 65 deg delta wing and the 20 deg trapezoidal wing at trimmed and untrimmed conditions.

Wood, R. M.↗
NASA NTRS1983

Experimental investigation of leading-edge thrust at supersonic speeds

Wings, designed for leading edge thrust at supersonic speeds, were investigated in the Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.80, 2.00, 2.16, and 2.36. Experimental data were obtained on a uncambered wing which had three interchangeable leading edges that varied from sharp to blunt. The leading edge thrust concept was evaluated. Results from the investigation showed that leading edge flow separation characteristics of all wings tested agree well with theoretical predictions. The experimental data showed that significant changes in wing leading edge bluntness did not affect the zero lift drag of the uncambered wings.

Wood, R. M.↗
NASA NTRS1983

An investigation of wing leading-edge vortices at supersonic speeds

Studies at subsonic and transonic speeds of the fundamental vortex behavior on the leeward surface of wings have led to the design of several unique and novel leading-edge devices commonly referred to as 'vortex flaps'. The present investigation has the objective to provide some fundamental vortex-flow results obtained at supersonic speeds. Experimental studies were performed in which pressure data and several types of flow visualization data were obtained on the leeward surface of a series of flat delta-wing models to identify the various flow mechanisms which can occur and to determine the effect of leading-edge sweep, Mach number, and angle of attack on the vortex strength and location. The reported investigation forms part of a study which is to explore the use of wing leading-edge vortex technology as a supersonic wing-design tool. The obtained results indicate that the procedure of distributing the vortex force as a pressure variation about a vortex action line is a promising concept.

Miller, D. S.↗
NASA NTRS1983

Status review of a supersonically-biased fighter wing-design study

Results from an ongoing supersonically-biased fighter wing-design study are summarized. The study has been conducted to explore the effects of supersonic aerodynamic performance, transonic maneuvering, low-speed/high angle-of-attack characteristics, and airframe system integration requirements on fighter aircraft wing design. The approach adopted involves the theoretical and experimental investigation of four advanced aircraft configurations which differ only in wing geometry. Supersonic and low-speed/high angle-of-attack wind tunnel results have been obtained for 20 deg trapezoidal, 65 deg delta, 70/30-deg advanced cranked, and 70/66-deg advanced cranked wing configurations. The supersonic data show that the advanced cranked wings outperform the trapezoidal and delta wings at cruise and moderate lift conditions. Low-speed/high angle-of-attack results show that all wings have significant stability problems above an angle of attack of 20 deg. Aircraft sizing analysis results show that the advanced cranked-wing configurations are significantly lighter, based upon take-off gross weight, than either the trapezoidal or the delta wings.

Wood, R. M.↗
NASA NTRS1983

An overview of two nonlinear supersonic wing design studies

The progress of two studies which apply nonlinear aerodynamics to supersonic wing design is reviewed. The first study employed a nonlinear potential flow code to design wings for high lift and low drag due to lift by employing a controlled leading-edge expansion in which the crossflow accelerates to supercritical conditions and decelerates through a weak shock. The second study utilized a modified linearized theory code to explore the concept of using 'attainable' leading-edge thrust as a guide for selecting a wing leading-edge shape (planform and radius) for maintaining attached flow and maximizing leading-edge thrust. Experimental and theoretical results obtained during the course of these two studies are discussed.

Miller, D. S.↗
NASA NTRS1982

An initial look at the supersonic aerodynamics of twin-fuselage aircraft concepts

Results of two studies into the supersonic aerodynamics of twin-fuselage aircraft configurations are summarized. In the first study, a set of experimental data was obtained on a simple rectangular-wing twin-fuselage wind-tunnel model; this data was then used to evaluate prediction methods, assess favorable interference effects, and identify any unexpected or unpredictable aerodynamic phenomena. Results are presented which show that significant reductions in wave drag are possible through optimum body positioning and that existing aerodynamic prediction methods are adequate for making preliminary aerodynamic estimates. Several configuration concepts were theoretically explored in the second study, and results are presented which indicate the sensitivity of the twin-fuselage concept to various methods of integrating the aircraft components.

Wood, R. M.↗