Engineering topics

Woods, William C.

Publications and source records attributed to Woods, William C..

9 records

NASA NTRS2002

Preliminary Investigation of Stagnation Point Liquid Injection Influence on Blunt Body Aerodynamics

A preliminary investigation has been performed to determine the influence of stagnation point water injection on the hypersonic aerodynamic forces and moments for two-dimensional blunt bodies. This investigation was performed in the Langley 20-Inch Mach 6 Air Tunnel, and represents the qualitative first phase of a study to examine the potential benefits of water injection to reduce aerodynamic drag and aero-heating. Tests with a 4-inch diameter hemisphere cylinder and a 4-inch diameter cylinder with a span 1.5 times the diameter were performed over a range of free-stream unit Reynolds number from two million to six million per ft and of angle of attack (-5 deg to 5 deg) with water and gaseous nitrogen injection at the geometric stagnation point. The momentum flux ratio, that is, the ratio of the momentum flux of the jet to that of the free-stream flow, was varied from the non-blowing value of zero up to 0.00031 by maintaining the jet momentum fixed and varying the free-stream momentum, hence Reynolds number. The effect of water injection on the aerodynamic drag coefficient for the hemisphere cylinder was observed to be negligible as the momentum flux ratio was increased to 0.00017, but decreased significantly as this ratio increased above 0.00017; a nearly 50 percent reduction in drag occurred for a factor of two increase in momentum flux ratio.

Woods, William C.↗

NASA NTRS2001

Hyper-X Stage Separation Wind-Tunnel Test Program

NASA's Hyper-X research program was developed primarily to flight demonstrate a supersonic combustion ramjet engine, fully integrated with a forebody designed to tailor inlet flow conditions and a free expansion nozzle/afterbody to produce positive thrust at design flight conditions. With a point-designed propulsion system the vehicle must depend on some other means for boost to its design flight condition. Clean separation from this initial propulsion system stage within less than a second is critical to the success of the flight. This paper discusses the early planning activity, background, and chronology that developed the series of wind-tunnel tests to support multi-degree-of-freedom simulation of the separation process. Representative results from each series of tests are presented, and issues and concerns during the process and current status are highlighted.

Woods, William C.↗

NASA NTRS2000

Hyper-X Research Vehicle (HXRV) Experimental Aerodynamics Test Program Overview

This paper provides an overview of the experimental aerodynamics test program to ensure mission success for the autonomous flight of the Hyper-X Research Vehicle (HXRV). The HXRV is a 12-ft long, 2700 lb lifting body technology demonstrator designed to flight demonstrate for the first time a fully airframe integrated scramjet propulsion system. Three flights are currently planned, two at Mach 7 and one at Mach 10, beginning in the fall of 2000. The research vehicles will be boosted to the prescribed scramjet engine test point where they will separate from the booster, stabilize. and initiate engine test. Following 5+ seconds of powered flight and 15 seconds of cowl-open tares, the cowl will close and the vehicle will fly a controlled deceleration trajectory which includes numerous control doublets for in-flight aerodynamic parameter identification. This paper reviews the preflight testing activities, wind tunnel models, test rationale. risk reduction activities, and sample results from wind tunnel tests supporting the flight trajectory of the HXRV from hypersonic engine test point through subsonic flight termination.

Holland, Scott D.↗

NASA NTRS2000

Hyper-X Storage Separation Wind Tunnel Test Program

NASA's Hyper-X research program was developed primarily to flight demonstrate a supersonic combustion ramjet engine, fully integrated with a forebody designed to tailor inlet flow, conditions and a free expansion nozzle/afterbody to produce positive thrust at design flight conditions. With a point-designed propulsion system, the vehicle must depend upon some other means for boost to its design flight condition. Clean separation from this initial propulsion system stage within less than a second is critical to the success of the flight. This paper discusses the early planning activity, background, and chronology that developed the series of wind tunnel tests to support multi degree of freedom simulation of the separation process. Representative results from each series of tests are presented and issues and concerns during the process and current status will be highlighted.

Woods, William C.↗

NASA NTRS2000

Hyper-X Research Vehicle (HXRV) Experimental Aerodynamics Test Program Overview

This paper provides an overview of the experimental aerodynamics test program to ensure mission success for the autonomous flight of the Hyper-X Research Vehicle (HXRV). The HXRV is a 12-ft long, 2700 lb lifting body technology demonstrator designed to flight demonstrate for the first time a fully airframe integrated scramjet propulsion system. Three flights are currently planned, two at Mach 7 and one at Mach 10, beginning in the fall of 2000. The research vehicles will be boosted to the prescribed scramjet engine test point where they will separate from the booster, stabilize, and initiate engine test. Following 5+ seconds of powered flight and 15 seconds of cow-open tares, the cowl will close and the vehicle will fly a controlled deceleration trajectory which includes numerous control doublets for in-flight aerodynamic parameter identification. This paper reviews the preflight testing activities, wind tunnel models, test rationale, risk reduction activities, and sample results from wind tunnel tests supporting the flight trajectory of the HXRV from hypersonic engine test point through subsonic flight termination.

Holland, Scott D.↗

NASA NTRS1994

Pressure distributions on a 0.02-scale Space Shuttle orbiter nose at Mach 21.5 in helium

Pressure distributions on a 0.02-scale model of the Space Shuttle orbiter forward fuselage were obtained in the 22-inch aerodynamic leg of the Langley Hypersonic Helium Tunnel Facility at a nominal free-stream Mach number of 21.5 and a ratio of specific heats of 1.67 for inclusion in the database of the Shuttle entry air data system (SEADS). The data were measured at model angles of attack of 0 deg to 50 deg in 5 deg increments for zero sideslip angle and at model sideslip angles of -5 deg to 5 deg for angles of attack equal to 5, 20, 35, and 40 deg. These data displayed trends similar to those observed in other wind tunnels at Mach 6 and 10 in air. Specifically noted is a shift in the location of the stagnation point at angles of attack above 15 deg; this effect did not, however, occur in flight. By comparison, the data obtained at Mach 6 in the Langley Hypersonic CF4 Tunnel, corresponding to a lower ratio of specific heats in the postshock region than those in helium and air, showed some reduction of the stagnation point shift at the higher angles of attack. The differences between flight and wind tunnel pressure distributions are believed due primarily to high-temperature gas chemistry effects in flight, which include lower effective specific heat ratios but which were not completely duplicated in the wind tunnels.

Ashby, George C., Jr.↗

NASA NTRS1989

Aerodynamic Characteristics of a Proposed Personnel Launch System (PLS) Lifting-Body Configuration at Mach Numbers from 0.05 to 20.3

A wind-tunnel investigation was performed to determine the aerodynamic characteristics of a proposed lifting-body personnel launch system (PLS) configuration over a Mach range of 0.05 to 20.3. The test configuration had a low-aspect-ratio body with a flat undersurface and three fins on the upper aft body. Data are presented with a minimum of analysis. All of the experimental data were placed in a structured data base using the R:BASE system and are included on a CD-ROM available with this report.

Cruz, Christopher I.↗

NASA NTRS1989

Aerodynamic Characteristics of a Proposed Personnel Launch System (PLS) Lifting-Body Configuration at Mach Numbers from 0.05 to 20.3. Supplement

A wind-tunnel investigation was performed to determine the aerodynamic characteristics of a proposed lifting-body personnel launch system (PLS) configuration over a Mach range of 0.05 to 20.3. The test configuration had a low-aspect-ratio body with a flat undersurface and three fins on the upper aft body. Data are presented with a minimum of analysis. All of the experimental data were placed in a structured data base using the R:BASE system. This is the CD-ROM that is available for this report.

Cruz, Christopher I.↗

NASA NTRS1987

Experimental investigation of the aerodynamic characteristics for a winged-cone concept

Experimental longitudinal and lateral-directional aerodynamics were obtained for a generic aerodynamics were obtaiend for a generic winged-cone configuration having possible application as a transatmospheric vehicle concept. Data were obtained at Mach numbers from 0.6 to 20.0; Reynolds numbers, based on model length, between 2.5 and 5.3 million; and angles of attack from -4 to 20 deg. Results indicate a longitudinal center-of-pressure travel of about 23 percent of the fuselage length for the test Mach number range, with longitudinal instabilities noted at high-supersonic to hypersonic Mach numbers. These instabilities are coupled with directional instability at similar Mach numbers. Predictions with analytic codes, namely, the USAF DATCOM and the tangent-cone option of the Hypersonic Arbitrary Body Program, provided fair agreement with the experimental aerodynamic characteristics at low angles-of-attack.

Phillips, W. Pelham↗