Engineering topics

Wright, Karen E.

Publications and source records attributed to Wright, Karen E..

6 records

DOE OSTI2024

Exploring constituent redistribution in irradiated U-19Pu-14Zr fuel via electron probe microanalysis

Here, the phenomena of constituent redistribution, wherein a previously homogeneous metallic fuel forms discrete, radially concentric compositional zones upon irradiation was investigated by examining an irradiated U-19Pu-14Zr fuel (where numbers represent wt. %) with a burnup of 11.5 at.% with electron probe microanalysis (EPMA) and quadruple inductively coupled plasma mass spectroscopy (Q-ICP-MS). EPMA-generated U, Pu, and Zr compositional data obtained from a diameter traverse of the sample was converted to mass and was used to: 1) compare the overall fuel element analysis results between the two methods, 2) determine the number of compositionally distinct zones forming as a result of constituent redistribution; and 3) quantify the post-irradiation loss or gain of U, Pu, and Zr atoms in each distinct compositional zone. Weight percent concentrations of U, Pu, and Zr for the overall cross section compare favorably between the two analytical methods, suggesting that the spatially resolved EPMA analysis complements bulk chemical analysis. Among the four identified compositional zones, post-irradiation quantification of U, Pu, and Zr elemental atom content changes shows that the quantity of U atoms lost from the innermost zone is slightly less than the quantity of U atoms gained by the middle two zones, and the quantity of Zr atoms lost from the high-U third zone is slightly less than is gained by the two innermost zones. Pu is lost from all four zones, although the innermost zone and the high-U third zone lose a significantly higher percentage (> 22 %) of their initial Pu atoms than the other two zones. For all three elements, EPMA cannot distinguish between atoms lost due to transport to a different zone from atoms lost due to nuclear processes; however, the insight gained from using this process can be used to experiment with new modeling techniques to predict constituent redistribution in U-Pu-Zr fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Detailed characterization of a PWR fuel rod at high burnup in support of LOCA testing

Experimental investigations of the fuel microstructure and volatile fission products along the pellet of a high burnup specimen (local burnup 76 GWd/tHM) have been conducted to support future transient testing. Detailed microscopy examinations have been carried out at different length scales. Transmission electron microscopy has highlighted a significant amount of damage across the entire radius with the formation of networks of dislocations. The optical and scanning electron microscopy determined the formation of three zones in the pellet with different characteristics. An intermediate region with no grain subdivision, lower porosity than the central zone porosity and high retained fission gas in nanometric bubbles and in the matrix was present between r/r0 ˜ 0.55 and 0.8. The high retention of gas in this region might suggest that the region will be prone to fine fragmentation, in addition to the HBS. An abrupt transition in the structure was observed at mid radius, with a third region developing from the mid radius to the pellet center. In this part of the pellet, metallic and grey phases with size between hundreds of nanometers and a few micrometers have formed at grain boundaries. The majority of fission gas has been released from the grain matrix and the original grains have polygonised, forming sub-grain domains separated by low-angle grain boundaries. No final explanation can be given for the polygonization occurring in the center, but on the basis of the irradiation history and the analysis of all the post irradiation examination (PIE) data, it is postulated that the polygonization within the original grains is an effect of dynamic recovery occurring at high temperature in the fuel center.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Engineering & Microstructure Scale PIE Report on EBR-II X441A Metallic Fuel Pins for the MORPH Experiment

The objectives of this project are to increase fundamental understanding of irradiation induced metallic U-Pu-Zr fuel behavior and to obtain data needed for the development of irradiation models for metallic fuels in MARMOT. The requested metallic fuel pins are from the X441A experiment irradiated in Experimental Breeder Reactor (EBR)-II and will be provided by the PIs for the duration of the experiment. The purpose of the pins irradiated in the X441A assembly was to vary Zr composition and fuel slug diameter in order to provide data for the metallic fuel performance code “LIFEMETAL” [ANL-IFR-125]. The fuels of interest to this project are metallic fuels with several Zr compositions (in wt.%): U-19Pu-6Zr, U-19Pu-10Zr, and U-19Pu-14Zr, which were irradiated to a peak burnup of approximately 11 at.%. The cladding was the same for all three fuel pins (austenitic stainless steel D9), which allows investigation of fuel-cladding interaction (FCI) phenomena. Varying Zr content in fuel pins enables investigation of the effect of Zr on fuel restructuring and fuel-cladding compatibility. Engineering and microstructure scale PIE activities will be focused on investigation of fundamental aspect of fuel performance such as species diffusion and migration, fission product behavior, and constituent redistribution. Obtained microstructural information will be used as the basis for the development of MARMOT models of U-Pu-Zr fuel performance at the mesoscale. Experimental data obtained through this proposal will be used to provide this fundamental understanding which will serve as the foundation of the development of radiation models for U-Pu-Zr in MARMOT. It will also provide a starting point for the design of new experiments to provide data for the validation of these MARMOT models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

EPMA-Based Mass Balance Method for Quantitative Fission Product Distribution Comparison between TRISO Particles

Two irradiated AGR-2 TRISO particles were chosen to demonstrate a recently developed mass balance technique in which EPMA-generated concentration data was used to determine fission product mass on a layer-by-layer basis in TRISO particles. EPMA-calculated fission product masses for most fission products in the two particles were within +/- 20% of their ORIGEN-modelled masses. Results show that Sr, Ba, and Eu accumulate preferentially in the carbon-rich kernel periphery on the particles’ side that lacks a gap between the buffer and IPyC. In addition, the more mobile elements--Cs, Sr, and Pd, accumulate in greater quantity in the outer layers of particle AGR2-223-RS34 compared to particle AGR2-223-RS06, which has relatively more of those elements’ mass located in the kernel and kernel periphery, suggesting enhanced fission product transport in particle AGR2-223-RS34. This model can be used better understand and test fission product transport in TRISO particles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Fission product distribution in irradiated safety-tested and as-irradiated AGR-2 TRISO particles

In this work, two tristructural isotropic (TRISO)-coated nuclear fuel particles were examined by electron probe microanalysis (EPMA) as part of the Advanced Gas Reactor program. The compacts’ average irradiation temperatures ranged from approximately 1260 to 1290 °C. One particle was examined in the as-irradiated condition, while the other was subject to 1600 °C post-irradiation safety testing. This study was undertaken to test a newly-developed EPMA technique to determine fission product masses in TRISO particles on a layer-by-layer basis, and to compare fission product distributions between an as-irradiated and safety-tested particle. Fission product concentration profiles were collected along two radii in each particle, with measured concentrations used to compute the fission product mass in each TRISO particle layer. These measured masses were then compared to those predicted from ORIGEN modeling calculations. Data collected from these measurements show that for these two particles, masses determined via EPMA were within ± 20% of the calculated masses for the rare-earth elements, Mo, Zr, Cs, I, and Pd. Elements that tend to be less homogeneously distributed include Sr, Te, Eu, Ag, and possibly Ba. Measured Ag masses differed by more than 40% from the calculated mass. Lanthanides other than Eu remain primarily within the fuel kernel in the as-irradiated particle but in the safety-tested particle these element masses were divided approximately equally between the kernel and kernel periphery. In both particles, the majority of Sr and Eu accumulated in the carbon-rich kernel periphery, although in the safety-tested particle, Sr and Eu accumulated farther from the fuel kernel than occurred with irradiation alone. A greater mass fraction of mobile elements, such as Cs and I accumulated in the buffer and IPyC in the safety-tested particle as compared to the as-irradiated particle. When fully developed and tested, this mass balance approach to TRISO particle analysis has the potential to provide insight into fuel behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Out-of-pile and postirradiated examination of lanthanide and lanthanide-palladium interactions for metallic fuel

Palladium is being investigated as a fuel additive to bind with and potentially immobilize lanthanide fission products. A primary cause of fuel-cladding chemical interaction (FCCI) is the lanthanide fission products migrating to the fuel periphery and interacting with the cladding. This interaction will lead to wastage of the cladding and eventually to a cladding breach. Palladium has previously been identified as a promising additive used to prevent or decrease FCCI by reacting with the lanthanide fission products. In the current study, an alloy cast from the four highest abundant lanthanides found in irradiated metallic fuel, Nd, Ce, Pr, and La, with and without Pd, has been characterized using neutron diffraction, scanning electron microscopy, and electron probe microanalysis. In the lanthanide-Pd intermetallic compounds, all of the constituent compounds, i.e. Nd-Pd, Ce-Pd, La-Pd and Pr-Pd are known. There is very good agreement, both structurally and compositionally, between the out-of-pile lanthanide alloy and lanthanide fission products characterized in irradiated fuels. In both cases, the lanthanide elements form a solid solution in a hexagonal crystal structure. The out-of-pile lanthanide alloy follows Vegard's Law, with the measured and calculated (weighted average of constituents) lattice parameters being within 1% for both the a and c parameters. Pd bonds with the lanthanides (Ln) forming the phases LnPd and Ln7Pd3. The results indicate the properties of lanthanide compounds in irradiated metallic fuel can be reliably simulated in out-of-pile experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗