Engineering topics
Wright, Malcolm
Publications and source records attributed to Wright, Malcolm.
Power Beaming for Deep Space and Permanently Shadowed Regions
Power beaming involves the wireless transfer of power, and could provide a revolutionary new way to power spacecraft and vehicles operating in difficult to access regions. Power beaming has the potential to represent an alternative solution to power spacecraft and landers where sunlight is unavailable. It could provide a source of power to robotic systems in permanently shadowed regions or power landers and rovers from orbiting spacecraft (e.g.,Moon, Mars, Europa, Enceladeus, Miranda).
Status of NASA’s Deep Space Optical Communication Technology Demonstration
With NASA funding, the Deep Space Optical Communication (DSOC) Project at JPL is planning a system level technology demonstration of optical communications from deep space. A 22 cm diameter flight laser transceiver (FLT) is being developed for space flight. The FLT will be designed to transmit an average laser power of 4W at 1550 nm and receive a weak 1064 nm laser signal (> 100 femtowatts). Use of the Hale telescope at Palomar Mountain, CA, retrofitted with a photoncounting receiver to detect the downlink from space, is planned. The Optical Communication Telescope Laboratory (OCTL) at Table Mountain, CA will transmit a 1064 nm laser beacon to serve as a pointing reference for the FLT and support low-rate uplink data-rates. The DSOC FLT is part of the baseline payload for the Psyche mission spacecraft recently selected for flight by NASA, providing link demonstration opportunities during the mission cruise phase. Link demonstration opportunities at distances of approximately 0.1 to 2 astronomical units (AU) are expected. The DSOC system is being designed to support downlink data-rates of 0.2 to > 200 Mb/s and uplink data rates of approximately 1.6 kb/s. A status update of DSOC Project activities on flight and ground development will be summarized in this paper.
Status of NASA's Deep Space optical communications technology demonstration
UNKNOWN
LEO-to-Ground Optical Communications Link Using Adaptive Optics Correction on the OPALS Downlink
No abstract available
OCTL Planning, Tests and Operations for the Bi-Directional Link to the OICETS
No abstract available
Preliminary Results of the OCTL to OICETS Optical Link Experiment (OTOOLE)
JPL in collaboration with JAXA and NICT demonstrated a 50Mb/s downlink and 2Mb/s uplink bi-directional link with the LEO OICETS satellite. The experiments were conducted in May and June over a variety of atmospheric conditions. Bit error rates of 10-(sup 1) to less than 10-? were measured on the downlink. This paper describes the preparations, precursor experiments, and operations for the link. It also presents the analyzed downlink data results.
Emulating an Optical Planetary Access Link with an Aircraft
Video imagery was streamed from the ground to an aircraft using a free-space laser communication link. The link operated at 270 Mb/s over slant ranges of 5-9 km in day and night time background conditions. The experiment was designed to demonstrate autonomous link acquisition and served as a first proof-of-concept for a planetary access link between a surface asset and an orbiter at Mars. System parameters monitored during the link demonstration including acquisition and tracking and communication performance are discussed.
Demonstration of a High-Efficiency Free-Space Optical Communications Link
In this paper we discuss recent progress on the implementation of a hardware free-space optical communications test-bed. The test-bed implements an end-to-end communications system comprising a data encoder, modulator, laser-transmitter, telescope, detector, receiver and error-correction-code decoder. Implementation of each of the component systems is discussed, with an emphasis on 'real-world' system performance degradation and limitations. We have demonstrated real-time data rates of 44 Mbps and photon efficiencies of approximately 1.8 bits/photon over a 100m free-space optical link.
Pointing Reference Scheme for Free-Space Optical Communications Systems
A scheme is proposed for referencing the propagation direction of the transmit laser signal in pointing a free-space optical communications terminal. This recently developed scheme enables the use of low-cost, commercial silicon-based sensors for tracking the direction of the transmit laser, regardless of the transmit wavelength. Compared with previous methods, the scheme offers some advantages of less mechanical and optical complexity and avoids expensive and exotic sensor technologies. In free-space optical communications, the transmit beam must be accurately pointed toward the receiver in order to maintain the communication link. The current approaches to achieve this function call for part of the transmit beam to be split off and projected onto an optical sensor used to infer the pointed direction. This requires that the optical sensor be sensitive to the wavelength of the transmit laser. If a different transmit wavelength is desired, for example to obtain a source capable of higher data rates, this can become quite impractical because of the unavailability or inefficiency of sensors at these wavelengths. The innovation proposed here decouples this requirement by allowing any transmit wavelength to be used with any sensor. We have applied this idea to a particular system that transmits at the standard telecommunication wavelength of 1,550 nm and uses a silicon-based sensor, sensitive from 0.5 to 1.0 micrometers, to determine the pointing direction. The scheme shown in the figure involves integrating a low-power 980-nm reference or boresight laser beam coupled to the 1,550-nm transmit beam via a wavelength-division-multiplexed fiber coupler. Both of these signals propagate through the optical fiber where they achieve an extremely high level of co-alignment before they are launched into the telescope. The telescope uses a dichroic beam splitter to reflect the 980- nm beam onto the silicon image sensor (a quad detector, charge-coupled device, or active-pixel-sensor array) while the 1,550- nm signal beam is transmitted through the optical assembly toward the remotely located receiver. Since the 980-nm reference signal originates from the same single-mode fiber-coupled source as the transmit signal, its position on the sensor is used to accurately determine the propagation direction of the transmit signal. The optics are considerably simpler in the proposed scheme due to the use of a single aperture for transmitting and receiving. Moreover, the issue of mechanical misalignment does not arise because the reference signal and transmitted laser beams are inherently co-aligned. The beam quality of the 980-nm reference signal used for tracking is required to be circularly symmetric and stable at the tracking-plane sensor array in order to minimize error in the centroiding algorithm of the pointing system. However, since the transmit signal is delivered through a fiber that supports a single mode at 1,550 nm, propagation of higher order 980-nm modes is possible. Preliminary analysis shows that the overall mode profile is dominated by the fundamental mode, giving a near symmetric profile. The instability of the mode was also measured and found to be negligible in comparison to the other error contributions in the centroid position on the sensor array.
Adaptive optics for daytime deep space laser communications to Mars
This paper describes JPL research in adaptive optics (AO) to reduce the daytime background noise on a Mars-to-Earth optical communications link. AO can reduce atmosphere-induced wavefront aberrations, and enable single mode receiver operation thereby buying back margin in the deep space optical communications link.
Data Relay Board with Protocol for High-Speed, Free-Space Optical Communications
In a free-space optical communication system, the mitigation of transient outages through the incorporation of error-control methods is of particular concern, the outages being caused by scintillation fades and obscurants. The focus of this innovative technology is the development of a data relay system for a reliable high-data-rate free-spacebased optical-transport network. The data relay boards will establish the link, maintain synchronous connection, group the data into frames, and provide for automatic retransmission (ARQ) of lost or erred frames. A certain Quality of Service (QoS) can then be ensured, compatible with the required data rate. The protocol to be used by the data relay system is based on the draft CCSDS standard data-link protocol Proximity-1, selected by orbiters to multiple lander assets in the Mars network, for example. In addition to providing data-link protocol capabilities for the free-space optical link and buffering the data, the data relay system will interface directly with user applications over Gigabit Ethernet and/or with highspeed storage resources via Fibre Channel. The hardware implementation is built on a network-processor-based architecture. This technology combines the power of a hardware switch capable of data switching and packet routing at Gbps rates, with the flexibility of a software- driven processor that can host highly adaptive and reconfigurable protocols used, for example, in wireless local-area networks (LANs). The system will be implemented in a modular multi-board fashion. The main hardware elements of the data relay system are the new data relay board developed by Rockwell Scientific, a COTS Gigabit Ethernet board for user interface, and a COTS Fibre Channel board that connects to local storage. The boards reside in a cPCI back plane, and can be housed in a VME-type enclosure.
Lidar for Guidance of a Spacecraft or Exploratory Robot
A report describes the Laser Mapper (LAMP) -- a lightweight, compact, low-power lidar system under development for guidance of a spacecraft or exploratory robotic vehicle (rover) at Mars or another planet. The LAMP is intended especially for use during rendezvous of two spacecraft in orbit, for mapping terrain during descent and landing of a spacecraft, for capturing a sample that has been launched into orbit, or navigation and avoidance of obstacles by a rover traversing terrain. The LAMP includes a laser that emits high-power, short light pulses. The laser beam is aimed in azimuth and elevation by use of a mirror on a two-axis gimbal, which scans the beam across a field of regard. Light reflected by a target is collected by a telescope, and the distance to the target is determined by measuring the round-trip travel time for reflected light pulses. The distance information is combined with directional information to construct a three-dimensional map of targets in the field of regard.
Qualification and reliability testing of a microchip laser system for space applications
Explore the source record for details and available documents.