Search NASA⌕ Search

Engineering topics

Wu, C. B.

Publications and source records attributed to Wu, C. B..

12 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Experimental investigation of PDI bifurcation of lower hybrid waves during electron density ramp-up in EAST

Abstract The effect of parametric decay instability (PDI) on the current drive efficiency of 4.6 GHz lower hybrid (LH) waves in EAST is investigated experimentally, showing the PDI channel bifurcation of LH waves for the first time in EAST. First, experiments with three platforms of LH power were performed, achieving the LH power required for the PDI occurrence. Second, PDI bifurcation experiments were further carried out by ramping up the plasma electron density. The loop voltage increases with an increase in density, implying a decrease in the current driven by the LH wave. PDI bifurcation during electron density ramp-up was studied by analyzing the parallel refractive index ( n ∥ ) and the frequency spectrum broadening, which is measured with a radio frequency magnetic probe array recently installed close to the LH antenna. It is observed for the first time that they both first increase with density, then there is not much variation and a clear sideband in the frequency spectrum is also observed when the density is up to 4 × 10 19 m − 3 , suggesting a change in the PDI channel. Calculation of the mode growth rate driven by PDI shows that when the edge electron density is up to 1.9 × 10 18 m − 3 , the growth rate of the ion cyclotron quasi-mode (ICQM) will exceed that of the ion sound quasi-mode (ISQM), quantitively explaining that with an increase in density, the PDI channel partly transits from the ISQM to the ICQM channel. Studies provide a possible way to reduce the power deposition in the edge region and improve drive capability by means of mitigating PDI behavior.

Physics↗
DOE OSTI2023

Plasma heating by electron cyclotron wave and the temperature effects on lower hybrid current drive on EAST

This paper presents the progress in the long—pulse operation of the electron cyclotron (EC) system and the achievements in high—electron temperature plasmas by the combined EC and lower hybrid (LH) waves heating since the EC system was built in 2015. An electron temperature of up to 12 keV with a duration over 100 s was realized by the simultaneous heating of EC and LH waves at the line-averaged density ${\bar n_{\text{e}}}$ ~1.8 × 10 19 m –3 . The plasma heating effect strongly depends on the location of EC power deposition. H-mode plasmas with solely EC wave auxiliary heating have been obtained on EAST for the first time. These H-mode discharges show an enhanced confinement factor H 98(y,2) around 1.0, which is higher than the previous H-mode using LH power alone (Xu et al 2011 Nucl. Fusion 51 072001). The total heating power is very close to the threshold value for L–H transition according to the international tokamak scaling. In addition to the temperature effects inside the separatrix, higher electron temperature produced by EC wave is found to reduce the LH power loss in the scrape-off layer due to collisional absorption, which is beneficial to further increase the LH current drive efficiency. Ray-tracing/Fokker–Planck modeling results indicate that higher electron temperature can shorten the LH wave propagation on EAST in a multiple-pass regime, thus decreasing the collisional dissipation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Observation and analysis of lower-hybrid-current-drive density limit in EAST

Lower hybrid current drive (LHCD) experiments with line-averaged density up to ~5.1 × 10 19 m –3 were performed in EAST L-mode plasmas. When the line-averaged density rises above a critical value, the hard x-ray (HXR) emission falls to the noise level, indicating that the LHCD density limit is encountered. The experimental results show that the LHCD density limit can be increased with higher wave source frequency (ƒ 0 ) and higher magnetic field (B t ). Although a higher LHCD density limit is obtained by a higher magnetic field for both 2.45 GHz and 4.6 GHz waves, the results show a stronger dependence on the magnetic field for the 4.6 GHz case. Analysis suggests that, for normal operation with a relatively low magnetic field (1.6 T $\leqslant$ B t $\leqslant$ 2.5 T) on EAST, the dominant mechanisms responsible for the LHCD density limit are different between the 2.45 GHz and 4.6 GHz waves. The wave accessibility plays a more significant role during 4.6 GHz LHCD experiments, while parasitic losses due to parametric decay instability (PDIs) dominate the accessibility issue in the 2.45 GHz case. Collisional loss in the scrape-off layer (SOL) may explain the 4.6 GHz result when combined with the accessibility limit at high density and low temperature.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Diagnostic development for parallel wave-number measurement of lower hybrid waves in EAST

An eight-channel magnetic probe diagnostic system has been designed and installed adjacent to the 4.6 GHz lower hybrid (LH) grill antenna in the low-field side of the EAST tokamak in order to study the n|| evolution of lower hybrid waves in the first pass from the launcher to the core plasma. The magnetic probes are separated by 6.6 mm, which allows measurement of the dominant parallel refractive index n|| up to n|| =5 for 4.6GHz LH waves. The magnetic probes are designed to be sensitive to the magnetic field component perpendicular to the background magnetic field with a slit on the casing that encloses the probe. The intermediate frequency (IF) stage, which consists of two mixing stages, down-coverts the frequency of the measured wave signals at 4.6 GHz to 20 MHz. A bench test demonstrates the phase stability of the magnetic probe diagnostic system. By evaluating the phase variation of the measured signals along the background magnetic field, the dominant n|| of the LH wave in the scrape-off layer (SOL) has been deduced during the 2019 experimental campaign. In the low density plasma, the measured dominant n|| of the lower hybrid waves is about 2.1, corresponding to the main peak 2.04 of the launched n|| spectrum. The n|| deduced by the least square linear fit method remains near this value in the low density plasma with a high spatial correlation magnitude of 0.9. With an eight-channel probe system a wave-number spectrum has also been deduced, which has a peak near to the measured dominant n||.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Impact of lithium wall conditioning and wave-frequency on high density lower hybrid current drive experiment on EAST

A series of dedicated lower hybrid current drive (LHCD) experiments on EAST shows that lithium wall conditioning extends LH current drive and heating up to the line-averaged density of n ̅_e≈ 4x1019 m-3 for both 2.45 and 4.6 GHz. Current drive at such a high density is crucial for the development of long-pulse non-inductive scenarios on EAST. With lithiation, the LH power injection of 1.5 MW at 2.45 GHz resulted in a drop of loop voltage of ~ 0.3 V, which is a comparable loop voltage drop observed with 1.1 MW at 4.6 GHz. The observed decrease in loop voltage is attributed mostly to the RF heating effect. Another LHCD experiment suggests that lithium wall coating has a more significant impact on the scrape-off-layer (SOL) properties than changes in the Greenwald fraction. LHCD at 2.45 GHz still suffers from a loss of efficiency. Enhanced power ionization in front of the launcher may cause the onset of density-dependent wave instabilities. The rise in the midplane SOL density may also accelerate a transition in the divertor regime, leading to additional ionization and collisional losses in the X-point divertor plasma. Ray-tracing modeling supports that a lower wave frequency is more prone to collisional power loss. The experiments confirm that lithiation is a useful tool to control the SOL plasma, and suggest that density control in front of the launcher may be critical to mitigating power loss mechanisms in the plasma boundary.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Simulated effect of edge plasma density parameters on lower hybrid wave scattering in EAST

The incorporation of lower hybrid (LH) wave spectrum broadening in the poloidal wavenumber (⁠k θ ) space at the last close field surface (LCFS) is reported to lead to better agreement of the modeled LH wave current profile with the experimental results [Baek et al., Nucl. Fusion 61, 106034 (2021)]. To further understand its underlying mechanism and find the possible influence factors, effects of wave scattering caused by drift-wave type density fluctuation on the probability distribution of the LH wave polar refractive index (⁠N θ ) at the LCFS are studied under density parameters in the scrape-off-layer. According to a scattering model [P. T. Bonoli and E. Ott, Phys Fluids 25(2), 359–375 (1982)], scattering probability and scattering angle distribution are two main factors that determine the degree of spectral broadening. Studies presented here show that the total scattering probability increases first and then decreases as the wave propagates toward a smaller normalized radius of poloidal magnetic flux (⁠ρ⁠). The degree of spectral broadening is found to depend on the density and density fluctuation together by changing the intensity and a proportion of the geometrical optics approximation term and the E×B drift term in the scattering model. Additionally, the fluctuation correlation length can significantly modify the probability distribution of N θ at the LCFS, which is found to significantly change the LH wave current profile.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

A model investigation of the impact of lower hybrid wave scattering angle on current drive profile in EAST and Alcator C-Mod

Lower hybrid current drive (LHCD) is beneficial for developing a steady-state operation scenario in a tokamak. This paper conducts a modeling investigation to identify an optimum rotation angle of the initial lower hybrid perpendicular (to the background magnetic field $\overrightarrow{B}$) wavevector for best matching the experimental RF current profile. It is hypothesized that central RF power deposition widely observed in the present-day LHCD experiments arises from wave scattering by turbulence. In a standard model without considering such interactions, the predicted power deposition profile is generally broad with off-axis peaking, not in agreement with experimental observations. A heuristic approach is adopted by introducing a spectral broadening mechanism by modifying the initial orientation of the perpendicular wavevector. The ray-tracing/Fokker–Planck solver GENRAY/CQL3D is utilized within the python-based π-scope framework. A focus is given to identify the perpendicular wavenumber orientation angle with respect to the magnetic surface normal vector at the initial ray location. Our modeling study shows that rotating the perpendicular wavevector in such a way as to increase the initial poloidal component is effective in reproducing the centrally peaked current profile observed in normal shear plasmas on both EAST and C-Mod. These waves can readily be absorbed to the central plasma, which reduces the sensitivity of the power deposition profile to a slight change of the plasma condition. The same approach is also found to help broaden the off-axis power deposition profile in a reverse-shear EAST plasma, leading to a better agreement with the experiment. The results presented here suggest that spectral modification arising from edge density fluctuations in a tokamak may need to be considered in understanding wave propagation and absorption. A further experimental and theoretical/modeling study is vital as a reverse approach is adopted in this study. Finally, our work suggests that mitigation or control measures are critical for parasitic effects occurring on the first pass in a reactor regime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Scoping study of lower hybrid current drive for CFETR

The paper assesses the applicability of lower hybrid current drive (LHCD) for two potential operating scenarios for the China Fusion Engineering Test Reactor (CFETR): the “hybrid” scenario in which some of the plasma current is sustained by the Ohmic transformer, and the fully non-inductive “steady state” scenario. Here, the πScope workflow engine was used to set up a large number of ray tracing/Fokker-Planck simulations (> 10 4 ) with parametric scans in the antenna poloidal position and launched parallel refractive index (n || ) for both the hybrid and steady state scenarios. Modeling predicts efficient off-axis current drive (1.3 MA for 20 MW launched power) with a peak near ρ of 0.6-0.65 for waves launched from the high field side (HFS). Waves launched from the low field side (LFS) damp at larger radius (ρ > 0.73) with similar efficiency to HFS launch. Stability analysis of the CFETR scenarios favors current drive profiles peaked near the mid-radius, suggesting that HFS launch is preferable due to the current drive location. The effect of wave scattering from density blobs in the edge/scrape-off-layer region was assessed through rotation of the perpendicular wavenumber at the ray origin. Simulations show that this effect can be quite large both in efficiency and damping location, however by adjusting the launched n|| much of the unperturbed performance can be recovered.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Modeling the spectral modification of lower hybrid wave in the presence of drift-wave type density fluctuation in the scrape-off-layer of the EAST tokamak

In this work, the spectrum change of the lower hybrid (LH) waves caused by a low-frequency density fluctuation in the scrape-off-layer is studied by applying the wave scattering model developed by Bonoli and Ott [Phys. Fluids 25, 359 (1982)] via a Monte Carlo method. A ray-tracing model specific to this purpose is developed to evaluate the probability distribution of both the poloidal refractive index (N θ ) and the parallel refractive index (N ∥ ) of the LH wave at the last closed flux surface (LCFS).The probability distributions of N ∥ and N θ at the LCFS are studied using the EAST parameters as a function of wave frequency, the initial N ∥ , and the polar injection position, which may influence the lower hybrid current drive efficiency.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Effect of edge plasma density on hot spot in LHCD plasma in EAST

Hot spots are a serious challenge limiting long pulse operation with lower hybrid current drive (LHCD) in tokamaks. Here, in order to mitigate hot spots in the guard limiter and improve LHCD capability, the effect of edge plasma density on inducing hot spots and current drive has been studied in EAST. The temperature in the guard limiter of the LH antenna, inducing hot spot directly, increases with edge density and LH power. Studies show that the hot spot is mainly ascribed to the heat flux in front of LH antenna. Further simulation indicates that such spots correspond to the peak position of edge density due to local LH electric field. In addition, due to the stronger parametric instability (PI) behavior in the case of higher edge density, the current drive capability decreases with edge density. Strike-point splitting behaviour appears as density increase, in agreement with current profiles in the edge region and the reduction of total driven current, suggesting that more power is deposited in the edge region, which then contributes more to hot spot formation. These studies offer one possible idea to optimize the edge density so as to satisfy the coupling, mitigate the heat flux in the guard limiter, and improve current drive capability in fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Diagnostic development for parallel wave-number measurement of lower hybrid waves in EAST

In this study, an eight-channel magnetic probe diagnostic system has been designed and installed adjacent to the 4.6 GHz lower hybrid (LH) grill antenna in the low-field side of the Experimental Advanced Superconducting Tokamak (EAST) in order to study the n ∥ evolution of LH waves in the first pass from the launcher to the core plasma. The magnetic probes are separated by 6.6 mm, which allows measurement of the dominant parallel refractive index n ∥ up to n ∥ = 5 for 4.6 GHz LH waves. The magnetic probes are designed to be sensitive to the magnetic field component perpendicular to the background magnetic field with a slit on the casing that encloses the probe. The intermediate frequency stage, which consists of two mixing stages, down-coverts the frequency of the measured wave signals at 4.6 GHz to 20 MHz. A bench test demonstrates the phase stability of the magnetic probe diagnostic system. By evaluating the phase variation of the measured signals along the background magnetic field, the dominant n ∥ of the LH wave in the scrape-off layer has been deduced during the 2019 experimental campaign. In the low density plasma, the measured dominant n ∥ of the LH waves is about 2.1, corresponding to the main peak 2.04 of the launched n ∥ spectrum. n ∥ deduced by the least-squares linear fit method remains near this value in the low density plasma with a high spatial correlation magnitude of 0.9. With an eight-channel probe system, a wave-number spectrum has also been deduced, which has a peak near to the measured dominant n ∥ .

47 OTHER INSTRUMENTATION↗