Engineering topics
Wu, Erik A.
Publications and source records attributed to Wu, Erik A..
Investigating dry room compatibility of sulfide solid-state electrolytes for scalable manufacturing
All-solid-state batteries (ASSBs) are viewed as promising next-generation energy storage devices, due to their enhanced safety by replacing organic liquid electrolytes with non-flammable solid-state electrolytes (SSEs). The high ionic conductivity and low Young's modulus of sulfide SSEs make them suitable candidates for commercial ASSBs. Nevertheless, sulfide SSEs are generally reported to be unstable in ambient air. Moreover, instead of gloveboxes used for laboratory scale studies, large scale production of batteries is usually conducted in dry rooms. Thus, this study aims to elucidate the chemical evolution of a sulfide electrolyte, Li 6 PS 5 Cl (LPSCl), during air exposure and to evaluate its dry room compatibility. When LPSCl is exposed to ambient air, hydrolysis, hydration, and carbonate formation can occur. Moreover, hydrolysis can lead to irreversible sulfur loss and therefore LPSCl cannot be fully recovered in the subsequent heat treatment. During heat treatment, exposed LPSCl undergoes dehydration, decomposition of carbonate species, and reformation of the LPSCl phase. Lastly, LPSCl was found to exhibit good stability in a dry room environment and was subject to only minor conductivity loss due to carbonate formation. The dry room exposed LPSCl sample was tested in a LiNi 0.8 Co 0.1 Mn 0.1 O 2 |LiIn half-cell, exhibiting no significant loss of electrochemical performance compared with the pristine LPSCl, proving it to be compatible with dry room manufacturing processes.
A stable cathode-solid electrolyte composite for high-voltage, long-cycle-life solid-state sodium-ion batteries
Rechargeable solid-state sodium-ion batteries (SSSBs) hold great promise for safer and more energy-dense energy storage. However, the poor electrochemical stability between current sulfide-based solid electrolytes and high-voltage oxide cathodes has limited their long-term cycling performance and practicality. Here, we report the discovery of the ion conductor Na 3-x Y 1-x Zr x Cl 6 (NYZC) that is both electrochemically stable (up to 3.8 V vs. Na/Na + ) and chemically compatible with oxide cathodes. Its high ionic conductivity of 6.6 × 10 –5 S cm –1 at ambient temperature, several orders of magnitude higher than oxide coatings, is attributed to abundant Na vacancies and cooperative MCl 6 rotation, resulting in an extremely low interfacial impedance. A SSSB comprising a NaCrO 2 + NYZC composite cathode, Na 3 PS 4 electrolyte, and Na-Sn anode exhibits an exceptional first-cycle Coulombic efficiency of 97.1% at room emperature and can cycle over 1000 cycles with 89.3% capacity retention at 40 °C. These findings highlight the immense potential of halides for SSSB applications.
Nano-Ceramic Cathodes via Co-sputtering of Gd–Ce Alloy and Lanthanum Strontium Cobaltite for Low-Temperature Thin-Film Solid Oxide Fuel Cells
We report the electrochemical performance and structural characteristics of porous nanostructured ceramic cathodes for thin-film solid oxide fuel cells (TF-SOFCs) based on yttria-stabilized zirconia (YSZ) electrolytes. The nanostructured cathode is obtained through magnetron co-sputtering of gadolinium–cerium (Gd–Ce) alloy and lanthanum strontium cobaltite perovskite targets. The resultant nanostructure and composition of the ceramic cathode are controlled by adjusting the co-sputtering conditions. The peak power densities in our fabricated TF-SOFCs are the highest reported values for YSZ-based electrolyte SOFCs, showing 0.14, 0.48, 1.21, 2.56, and 3.01 W/cm2 at 450, 500, 550, 600, and 650 °C, respectively, operating under air and pure hydrogen fuel. The results show that the porosity and composition of the cathode greatly affect the resulting peak power densities. This work illustrates the capability of sputtering to produce stable, scalable, nano-ceramic cathodes with superb peak power densities when integrated in TF-SOFCs.
All-Sputtered, Superior Power Density Thin-Film Solid Oxide Fuel Cells with a Novel Nanofibrous Ceramic Cathode
Thin film solid oxide fuel cells (TF-SOFCs) are attracting attention due to their ability to operate at comparatively lower temperatures (400–650 °C) that are unattainable for conventional anode-supported SOFCs (650–800 °C). However, limited cathode performance and cell scalability remain persistent issues. Here, we report a new approach of fabricating yttria-stabilized zirconia (YSZ)-based TF-SOFCs via a scalable magnetron sputtering process. Notable is the development and deposition of a porous La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 2.95 (LSCF)-based cathode with a unique fibrous nanostructure. This all-sputtered cell shows an open-circuit voltage of ~1.0 V and peak power densities of ~1.7 and ~2.5 W/cm 2 at 600 and 650 °C, respectively, under hydrogen fuel and air along with showing stable performance in short-term testing. The power densities obtained in this work are the highest among YSZ-based SOFCs at these low temperatures, which demonstrate the feasibility of fabricating exceptionally high-performance TF-SOFC cells with distinctive dense or porous nanostructures for each layer, as desired, by a sputtering process. This work illustrates a new, potentially low-cost, and scalable platform for the fabrication of next-generation TF-SOFCs with excellent power output and stability.
Revealing Nanoscale Solid–Solid Interfacial Phenomena for Long-Life and High-Energy All-Solid-State Batteries
Enabling long cyclability of high-voltage oxide cathodes is a persistent challenge for all-solid-state batteries, largely because of their poor interfacial stabilities against sulfide solid electrolytes. While protective oxide coating layers such as LiNbO 3 (LNO) have been proposed, its precise working mechanisms are still not fully understood. Existing literature attributes reductions in interfacial impedance growth to the coating's ability to prevent interfacial reactions. However, its true nature is more complex, with cathode interfacial reactions and electrolyte electrochemical decomposition occurring simultaneously, making it difficult to decouple each effect. Herein, we utilized various advanced characterization tools and first-principles calculations to probe the interfacial phenomenon between solid electrolyte Li6PS5Cl (LPSCl) and high-voltage cathode LiNi 0.85 Co 0.1 Al 0.05 O 2 (NCA). We segregated the effects of spontaneous reaction between LPSCl and NCA at the interface and quantified the intrinsic electrochemical decomposition of LPSCl during cell cycling. We report both experimental and computational results demonstrated improved thermodynamic stability between NCA and LPSCl after incorporation of the LNO coating. Additionally, we revealed the in situ passivation effect of LPSCl electrochemical decomposition. When combined, both these phenomena occurring at the first charge cycle result in a stabilized interface, enabling long cyclability of all-solid-state batteries.
Elucidating Reversible Electrochemical Redox of Li 6 PS 5 Cl Solid Electrolyte
Sulfide-based solid electrolytes are promising candidates for all solid-state batteries (ASSBs) due to their high ionic conductivity and ease of processability. However, their narrow electrochemical stability window causes undesirable electrolyte decomposition. Existing literature on Li-ion ASSBs report an irreversible nature of such decompositions, while Li–S ASSBs show evidence of some reversibility. Here, we explain these observations by investigating the redox mechanism of argyrodite Li 6 PS 5 Cl at various chemical potentials. We found that Li–In | Li 6 PS 5 Cl | Li 6 PS 5 Cl–C half-cells can be cycled reversibly, delivering capacities of 965 mAh g –1 for the electrolyte itself. During charging, Li 6 PS 5 Cl forms oxidized products of sulfur (S) and phosphorus pentasulfide (P 2 S 5 ), while during discharge, these products are first reduced to a Li 3 PS 4 intermediate before forming lithium sulfide (Li 2 S) and lithium phosphide (Li 3 P). Lastly, we quantified the relative contributions of the products toward cell impedance and proposed a strategy to reduce electrolyte decomposition and increase cell Coulombic efficiency.