Engineering topics
Publications and source records attributed to Wu, M. K..
We report the far-infrared reflectance and transmittance of superconducting ab-plane-oriented films in magnetic fields up to 30 Tesla.
In an attempt to enhance the electrical and mechanical properties of the high temperature superconducting oxides, high T(sub c) composites were prepared composed of the 123 compounds and AgO. The presence of extra oxygen due to the decomposition of AgO at high temperature is found to stabilize the superconducting 123 phase. Ag is found to serve as clean flux for grain growth and precipitates as pinning center. Consequently, almost two orders of magnitude enhancement in critical current densities were also observed in these composites. In addition, these composites also show much improvement in workability and shape formation. On the other hand, proper oxygen treatment of Y5Ba6Cu11Oy was found to possibly stabilize superconducting phase with T(sub c) near 250 K. I-V, ac susceptibility, and electrical resistivity measurements indicate the existence of this ultra high T(sub c) phase in this compound. Detailed structure, microstructure, electrical, magnetic and thermal studies of the superconducting composites and the ultra high T(sub c) compound are presented and discussed.
In an attempt to enhance the electrical and mechanical properties of the high temperature superconducting oxides, high T(sub c) composites were prepared composed of the 123 compounds and AgO. The presence of extra oxygen due to the decomposition of AgO at high temperature is found to stabilize the superconducting 123 phase. Ag is found to serve as clean flux for grain growth and precipitates as pinning center. Consequently, almost two orders of magnitude enhancement in critical current densities were also observed in these composites. In addition, these composites also show much improvement in workability and shape formation. On the other hand, proper oxygen treatment of Y5Ba6Cu11Oy was found to possibly stabilize superconducting phase with T(sub c) near 250 K. I-V, ac susceptibility, and electrical resistivity measurements indicate the existence of this ultra high T(sub c) phase in this compound. Detailed structure, microstructure, electrical, magnetic and thermal studies of the superconducting composites and the ultra high T(sub c) compound are presented and discussed.
Factors involved in the strong flux pinning effect of high-Tc YBa2Cu3O7/AgO (Y-123/AgO) composite and other REE-123/AgO composites were investigated. Samples of superconducting REE-123 and REE-123/AgO (where REE was Nd, Sm, Eu, Gd, Dy, Ho, Er, or Y) were prepared and used to obtain magnetic moments, critical field, and microstructure data. The optimum heat treatment conditions for the formation of strong flux-pinning REE-123/AgO composites were found to be different for different REE-123 compounds. It was found that the annealing temperature depends on the ionic size of the REE, with larger rare-earth ions requiring higher temperature. It was also found that strong flux-pinning REE-123/AgO composites form only in a narrow annealing temperature range.
Magnetic suspension effect was first observed in samples of YBa2Cu3O7/AgO(Y-123/AgO) composites. Magnetization measurements of these samples show a much larger hysteresis which corresponds to a large critical current density. In addition to the Y-123AgO composites, recently similar suspension effects in other RE-123/AgO, where RE stands for rare-Earth elements, were also observed. Some samples exhibit even stronger flux pinning than that of the Y-123/AgO sample. An interesting observation was that in order to form the composite which exhibits strong flux trapping effect the sintering temperature depends on the particular RE-123 compound used. The paper presents the detailed processing conditions for the formation of these RE-123/AgO composites, as well as the magnetization and critical field data.
This paper describes the processing conditions for the formation of strong flux pinning high-Tc (REE)1Ba2Cu3O7/AgO (RE-123/AgO) composites with the RE-123:AgO ratio of 3:1 and presents the magnetization and critical field data on these composites. The results obtained indicate that proper processing conditions are critical to the formation of strong flux pinning RE-123/AgO composites. Resistance measurements in a magnetic field show that the upper critical field in Y-123/AgO is about three times larger than that of the Y-123 compound.
Samples of YBa2Cu3O(x) doped with silver oxide (Tc is about 93 K) have exhibited attractive forces in gradient magnetic fields, both normal and tangential to the surfaces, which are more than twice the sample weight. This allows sample suspension below a rare earth magnet. Critical current density was increased by about 100 at 77 K. Persistent fields, flux pinning, magnetization, and modeling are described.
Superconducting Y1Ba2Cu3O7 ('123') films were fabricated on the Y2BaCuO5 ('211') phase substrate. The superconducting characteristics of these films, in terms of superconducting transition temperature (Tc) and width, are better than those using other oxide compounds as substrates. In addition, using high-temperature processing, the bulk 211 phase was converted into the 123 phase. A new high Tc copper oxide material with non-rare-earth elements (Bi-Sr-Cu-O) was prepared using similar high-temperature processing. High-temperature processing presents an alternative synthetic route in the search of new high Tc superconductors.
Experimental studies are reported whose results indicate that proper processing procedures are critical to the formation of high-temperature copper oxide superconductors. Superconducting 123 films can be fabricated using the green 211 phase as a substrate. The transition temperature and transition width characteristics of these films are better than those obtained when other oxide compounds are used as substrates. A compact or single-crystal 211 phase will be desirable as a substrate for high-quality thin films. A new high T(c) copper oxide compound with nonrare earth elements was prepared using high-temperature processing. A YBa2Cu3O7-Ag composite with improved electrical conductivity was also prepared.
High temperature processing was found to partially convert the green 211 phase oxide to 123 phase. High Tc superconductivity was observed in Bi-Sr-Cu-O and Y-Sr-Cu-O systems prepared using the same heat treatment process. High temperature processing presents an alternative synthetic route in the search for new high Tc superconductors. An unusual magnetic suspension with enhancement in critical current density was observed in the 123 and AgO composite.
On the basis of existing data it appears that the high-temperature superconductivity above 77 K reported here, occurs only in compound systems consisting of a phase other than the K2NiF4 phase. A narrow superconducting transition was obtained with T sub c0 = 98 K and T sub c1 = 94 K in Y-Ba-Cu-O (YBCO). Preliminary results indicate that YBCO is rather different from the layered LaBCO, LaSCO, and LaCCO. While electron-photon interaction cannot be absent from this compound system, nonconventional enhanced superconducting interactions due to interfaces, Resonating Valence Bond (RVB) states, or even a superconducting state beyond the BCS framework, may be required to account for the high T sub c in YBCO. It is believed that study of the possible subtle correlation between magnetism and superconductivity will definitely provide important insight into the superconducting mechanism in YBCO and other oxides.
The Al-In-Sn alloys were directionally solidified in the NASA KC-135 aircraft which flies a series of parabolas to generate high (high-g) and low (low-g) gravity forces parallel to the longitudinal growth axis. Thus, for a given sample, successive sections can be identified which were solidified in high-g and low-g. Measurements of the electronic properties of the samples reveal that: the resistivity of the low-g sections is larger (about a factor of 10) than that of the high-g sections; the low-g sections behave conductively like a semi-metal, while the high-g sections are essentially metallic; and both high-g and low-g sections are superconducting but the superconducting transition temperature of the low-g sections is 1 K higher than that of the high-g sections.
A stable and reproducible superconductivity transition between 80 and 93 K has been achieved and maintained in a Y-Ba-Cu-O compound system at ambient pressure in a simple liquid-nitrogen Dewar. An upper critical field Hc2(0) estimate of between 80 and 180 T is obtained, and the paramagnetic limiting field at 0 K for a sample with a T(c) of about 90 K is 165 T. It is suggested that the lattice parameters, the valence ratio, and the sample treatments all play a role in achieving superconductivity above 77 K.
A systematic study on the relationship between the microstructure and physical properties of several superconducting materials prepared by solidification in low gravity was conducted. Further study of the materials, such as the applications of hydrostatic pressure which is known to be an effective mean to vary the electronic structure of materials, in conjunction with the detailed microstructure analysis of the samples was also performed to better understand the low gravity effects on the enhancement of the electronic properties. Results of the studies on the directionally solidified AlInSn alloys processed in the KC-135 aircraft and immiscible GaBi alloy prepared during free fall in the Marshall Space Flight Center Drop Tower are presented.
Immiscible GaBi alloys were solidified during free fall in the NASA Marshall Space Flight Center drop tower, which provides about 4.5 seconds of low gravity. The electrical resistivity and magnetic susceptibility were measured as a function of pressure (up to 18 kbar) and temperature (300 K to 4.2 K) of drop tower (DT) and ground control (GC) samples prepared under identical conditions, except for gravity. At ambient pressure the electrical resistance of the DT sample exhibits a broad maximum at 100 K, while that of GC sample decreases rapidly as temperature decreases. Both DT and GC samples become superconducting at 7.7 K. However, a minor second superconducting phase with a transition temperature at 8.3 K is observed only in the DT samples.
The Al-In-Sn alloys were directionally solidified in the NASA KC-135 aircraft which flies a series of parabolas to generate high (high-g) and low (low-g) gravity forces parallel to the longitudinal growth axis. Thus, for a given sample, successive sections can be identified which were solidified in high-g and low-g. Measurements of the electronic properties of the samples reveal that: the resistivity of the low-g sections is larger (about a factor of 10) than that of the high-g sections; the low-g sections behave conductively like a semi-metal, while the high-g sections are essentially metallic; and both high-g and low-g sections are superconducting but the superconducting transition temperature of the low-g sections is 1 K higher than that of the high-g sections.