Search NASA⌕ Search

Engineering topics

Wu, Xin

Publications and source records attributed to Wu, Xin.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Stabilized hole-selective layer for high-performance inverted p-i-n perovskite solar cells

P-i-n geometry perovskite solar cells (PSCs) offer simplified fabrication, greater amenability to charge extraction layers, and low-temperature processing over n-i-p counterparts. Self-assembled monolayers (SAMs) can enhance the performance of p-i-n PSCs but ultrathin SAMs can be thermally unstable. Here we report a thermally robust hole-selective layer comprised of nickel oxide (NiO x ) nanoparticle film with a surface-anchored (4-(3,11-dimethoxy-7H-dibenzo[c,g]carbazol-7-yl)butyl)phosphonic acid (MeO-4PADBC) SAM that can improve and stabilize the NiO x /perovskite interface. The energetic alignment and favorable contact and binding between NiO x /MeO-4PADBC and perovskite reduced the voltage deficit of PSCs with various perovskite compositions and led to strong interface toughening effects under thermal stress. The resulting 1.53–electron-volt devices achieved 25.6% certified power conversion efficiency and maintained >90% of their initial efficiency after continuously operating at 65 degrees Celsius for 1200 hours under 1-sun illumination.

14 SOLAR ENERGY↗
DOE OSTI2022

Mechanism of chlorine-induced stress corrosion cracking of two 304 SS heats in simulated marine environment through in situ X-ray tomography and diffraction: Role of deformation induced martensite and crack branching

In this work, In-situ synchrotron x-ray tomography and diffraction experiments were conducted on two heats of 304SS undergoing chlorine-induced stress-corrosion-cracking (CISCC) in a simulated marine environment. The role of deformation induced martensite on CISCC was investigated through diffraction analysis where no significant amount of martensite was found to form during CISCC, indicating that it may not play a significant role in affecting the process. Tomography combined with stress-intensity analysis revealed the influence of stress-intensity on branching types with single crack growth, micro-branching, and macro-branching. Post experimental electron microscopy characterization revealed the presence of FeCl 2 , CrCl 2 , and NiCl 2 ·6H 2 O compounds at the crack, which infers a dissolution mechanism during the experiment. A dissolution mechanism highlighting the synergy between stress and corrosion was proposed to explain chlorine-induced stress-corrosion-cracking and crack branching.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of Electroacupuncture at Wushu Acupoints of the Cardiopulmonary Meridian on the Autophagy in Rats with Acute Myocardial Ischemia

Wushu acupoints are the five acupoints distributed below the human elbow and knee joint. They are all located on the same meridian and divided into five categories: Jing, Ying, Shu, Jing, and He. It has been shown that electroacupuncture (EA) at Shenmen point of heart meridian can improve acute myocardial ischemia (AMI) early. However, it is still unclear if all the Wushu acupoints of the heart meridian can improve AMI. Hence, this study emphasizes Wushu acupoints of heart meridian, compares them with Wushu acupoints of lung meridian, and studies the therapeutic effect of EA at Wushu acupoints on AMI and its possible mechanism. It also discusses the specificity of the heart meridian to heart disease. The AMI model is established by ligation of the left anterior descending coronary artery. The detection methods like the physiological recorder, TTC staining, ELISA, and so forth were used to determine the ECG, myocardial infarct size, serum myocardial enzymes, and myocardial tissue-related protein expression in rats. The heart rate (HR) and ST segment along with creatine kinase (CK), creatine kinase isoenzymes (CK-MB), lactate dehydrogenase (LDH), and myocardial infarctions increased after the induction with AMI. Furthermore, the expressions of PINK1 and Parkin protein also showed an increase. However, EA at Wushu acupoints in the heart meridian can reverse the above changes, whereas EA at the lung meridian exhibits limited effect. It is depicted that the heart meridian has a relatively specific relationship with the heart in a diseased state.

Zhu, Chao↗
DOE OSTI2022

Evaluation of Applied Stress on Atmospheric Corrosion and Pitting Characteristics in 304L Stainless Steel

For this study, the effects of applied stress, ranging from tensile to compressive, on the atmospheric pitting corrosion behavior of 304L stainless steel (SS304L) were analyzed through accelerated atmospheric laboratory exposures and microelectrochemical cell analysis. After exposing the lateral surface of a SS304L four-point bend specimen to artificial seawater at 50°C and 35% relative humidity for 50 d, pitting characteristics were determined using optical profilometry and scanning electron microscopy. The SS304L microstructure was analyzed using electron backscatter diffraction. Additionally, localized electrochemical measurements were performed on a similar, unexposed, SS304L four-point bend bar to determine the effects of applied stress on corrosion susceptibility. Under the applied loads and the environment tested, the observed pitting characteristics showed no correlation with the applied stress (from 250 MPa to -250 MPa). Pitting depth, surface area, roundness, and distribution were found to be independent of location on the sample or applied stress. The lack of correlation between pitting statistics and applied stress was more likely due to the aggressive exposure environment, with a sea salt loading of 4 g/m 2 chloride. The pitting characteristics observed were instead governed by the available cathode current and salt distribution, which are a function of sea salt loading, as well as pre-existing underlying microstructure. In microelectrochemical cell experiments performed in Cl - environments comparable to the atmospheric exposure and in environments containing orders of magnitude lower Cl - concentrations, effects of the applied stress on corrosion susceptibility were only apparent in open-circuit potential in low Cl - concentration solutions. Cl - concentration governed the current density and transpassive dissolution potential.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Development of a numerical model for simulating stress corrosion cracking in spent nuclear fuel canisters

Abstract Prediction and detection of the chloride-induced stress corrosion cracking (CISCC) in Type 304 stainless steel spent nuclear fuel canisters are vital for the lifetime extension of dry storage canisters. This paper conducts a critical review that focuses on the numerical modeling and simulation on the research progress of the CISCC. The numerical models emphasizing the residual stress, susceptible microstructure, and corrosive environment are summarized individually. Meanwhile, the simulation studies on the role of hydrogen-assisted cracking are reviewed. Finally, a multi-physical numerical model, which combines the different fields is proposed based on our recent investigation.

Materials Science↗
DOE OSTI2020

In situ synchrotron X-ray tomography of 304 stainless steels undergoing chlorine-induced stress corrosion cracking

To understand the mechanisms behind chlorine-induced stress corrosion cracking (CISCC) in 304 stainless steel, synchrotron high energy x-rays were used to perform in-situ x-ray microtomography on a pre-cracked sample under load in a corrosive simulated marine environment. The tomography scans showed the crack morphology evolving into a branching crack around the surface of the sample. Finite element analysis and stress intensity analysis are conducted to explain the observed crack branching.

304 Stainless Steel↗
DOE OSTI2020

On residual stress analysis and microstructural evolution for stainless steel type 304 spent nuclear fuel canisters weld joint: Numerical and experimental studies

Chloride-induced stress corrosion cracking (CISCC) in the weldments of austenitic stainless steel canisters is one of the primary safety concerns during the dry storage of used nuclear fuel at Independent Spent Fuel Storage Installations in coastal areas. In order to evaluate the CISCC behavior in the canister, a 3D sequentially coupled thermo-mechanical finite element model was built to simulate the residual stresses induced by two intersecting longitudinal and circumferential multi-pass welds in austenitic stainless steel mockup canister. Weld-induced residual stresses from simulation were in good agreement with the experimental measurement results by deep-hole drilling and contour methods. Through-wall high tensile axial and hoop stresses were observed in both the fusion zone and heat affected zone (HAZ) in the longitudinal and circumferential weld, respectively. On the other hand, the microstructure within the weldments of 304 stainless steel mockup was characterized using optical microscopy, scanning electron microscopy, electron back-scattered diffraction and energy dispersive X-ray spectroscopy methods. A few amount of MnS inclusions in both the base metal and HAZ, and a lot of (Mn,Si) x O y inclusions in the fusion zone were found. Meanwhile, there is some α'-martensite in the base metal, while the martensite was reversed in the HAZ. In the fusion zone, there is a lot of δ-ferrite. The martensite reversion phenomenon was also verified by the combination of Feritscope test and thermal simulation, which could predict a martensite reversion temperature as 400C°. The welding residual stresses and microstructure analysis results could offer the instructive information for the prediction of CISCC behavior of the spent nuclear fuel canisters.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Control of Weld Residual Stress in a Thin Steel Plate through Low Transformation Temperature Welding Consumables

Low transformation temperature welding (LTTW) consumables are characterized by a low martensite start temperature and a large fraction of martensite forming in the weld. It can efficiently reduce the tensile residual stress because the volume expansion associated with the martensitic transformation compensates for the thermal contraction during cooling. In this work, a LTTW wire, designated as EH200B, was created for the arc welding of advanced high-strength steel thin plates. In comparison to conventional ER70S-3 wires, this LTTW wire generated an opposite distortion pattern. Neutron diffraction measurements along the center thickness of the welded plates showed the maximum residual stress along the longitudinal direction (LD) in the weld region, and the heat-affected zone (HAZ) immediately adjacent to the weld region was reduced from ~330 MPa to below 240 MPa by using the LTTW wire. A finite element (FE) model was developed to predict the residual stress distributions of the plates welded under these two wires. The simulation results showed reasonable agreement with the volume-average neutron diffraction data. Compressive residual stress in the weld region using the LTTW wire was predicted by the FE method. Electron backscattered diffraction and x-ray diffraction measurements confirmed ~90% martensite was present in the LTTW weld. The fatigue life of DP980 steel lap joint panels using EH200B wire nearly doubled that of ER70S-3 wire. This improvement was attributed to the high strength and low LD residual stress in the weld and HAZ immediately adjacent to the weld.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Synthesis and anticancer activity evaluation of novel oxacalix[2]arene[2]pyrimidine derivatives

A series of novel oxacalix[2]arene[2]pyrimidine derivatives were synthesized, and their antitumor activities against HeLa, MCF7, HepG2, and A549 human cancer cell lines were evaluated using an MTT assay. Some of the synthesized compounds exhibited considerable anti-proliferative activity against the human cancer cell lines. Compound 5l, which contains an ethanolamine moiety, exhibited the strongest inhibitory activity against HepG2 with an IC{sub 50} value of 12.37 μM. Moreover, a cell apoptosis assay indicated that the anti-proliferative activity of 5l might be attributed to its induction of apoptosis. Our report highlights the potential anticancer efficacy of novel oxacalix[2]arene[2]pyrimidines.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2018

Embedded sensor system

A magnetic communication system for a gas turbine engine may include a sensor coupled to a microcontroller. A low frequency radio-frequency identification integrated chip may be coupled to the microcontroller. A first coupling circuit may be coupled to the low frequency radio-frequency identification integrated chip and may include a first coil winding wound within a first core. The first coil winding operatively associated with a low frequency magnetic flux.

42 ENGINEERING↗
DOE OSTI2018

Maternal supplementation with calcium varying with feeding time daily during late pregnancy affects lipid metabolism and transport of placenta in pigs

To investigate effects of Ca level varying with feeding time daily in sows during late pregnancy on placental lipid metabolism and transport in pigs, sixty pregnant sows were assigned to 3 groups: the CON group was fed low-Ca diet with 11.25 g CaCO3 at 0600 h and 1500 h, H-L group was fed low-Ca diet with 22.5 g CaCO3 at 0600 h and low-Ca diet at 1500 h, and L-H group was fed low-Ca diet at 0600 h and low-Ca diet with 22.5 g CaCO3 at 1500 h, respectively. Serum from sows and umbilical cord and placenta were collected during delivery. Results showed that, compared with the CON group, H-L feeding significantly increased maternal serum total triglyceride (TG) and umbilical serum high-density lipoprotein (HDL) (P P P < 0.05). It is concluded that maternal supplementation with Ca varying with feeding time daily during late pregnancy affects placental lipid metabolism and transport in pigs by regulating the mRNA expression related to lipid metabolism and the circadian clock.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2017

Additively Manufactured IN718 Components with Wirelessly Powered and Interrogated Embedded Sensing

A methodology is described for embedding commercial-off-the-shelf sensors together with wireless communication and power circuit elements using direct laser metal sintered additively manufactured components. Physics based models of the additive manufacturing processes and sensor/wireless level performance models guided the design and embedment processes. A combination of cold spray deposition and laser engineered net shaping was used to fashion the transmitter/receiving elements and embed the sensors, thereby providing environmental protection and component robustness/survivability for harsh conditions. By design, this complement of analog and digital sensors were wirelessly powered and interrogated using a health and utilization monitoring system; enabling real-time, in situ prognostics and diagnostics.

embedded sensing↗
DOE OSTI2017

EXPLICIT SYMPLECTIC-LIKE INTEGRATORS WITH MIDPOINT PERMUTATIONS FOR SPINNING COMPACT BINARIES

We refine the recently developed fourth-order extended phase space explicit symplectic-like methods for inseparable Hamiltonians using Yoshida’s triple product combined with a midpoint permuted map. The midpoint between the original variables and their corresponding extended variables at every integration step is readjusted as the initial values of the original variables and their corresponding extended ones at the next step integration. The triple-product construction is apparently superior to the composition of two triple products in computational efficiency. Above all, the new midpoint permutations are more effective in restraining the equality of the original variables and their corresponding extended ones at each integration step than the existing sequent permutations of momenta and coordinates. As a result, our new construction shares the benefit of implicit symplectic integrators in the conservation of the second post-Newtonian Hamiltonian of spinning compact binaries. Especially for the chaotic case, it can work well, but the existing sequent permuted algorithm cannot. When dissipative effects from the gravitational radiation reaction are included, the new symplectic-like method has a secular drift in the energy error of the dissipative system for the orbits that are regular in the absence of radiation, as an implicit symplectic integrator does. In spite of this, it is superior to the same-order implicit symplectic integrator in accuracy and efficiency. The new method is particularly useful in discussing the long-term evolution of inseparable Hamiltonian problems.

79 ASTRONOMY AND ASTROPHYSICS↗