Search NASA⌕ Search

Engineering topics

Wu, Y. C.

Publications and source records attributed to Wu, Y. C..

Deformation mechanisms in amorphous Ni–Mo–P films coated on CoCrFeNi high-entropy alloys

The Ni–Mo–P amorphous films were successfully deposited on the CoCrFeNi high-entropy alloys by electroless plating. This work will focus on reviewing and discussing the ambient-temperature mechanical properties, plastic deformation, and cracking mode of the coating-substrate system. The yielding strength (σ y ) and ultimate tensile strength (UTS) of the specimen plating for 1 h were 260 and 760 MPa, respectively, with 44.4% (σ y ) and 14.2% (UTS) improvement contrast to the uncoated HEAs (σ y and UTS are 180 MPa and 560 MPa, respectively). It is attributed to the back stress and repulsive image stress to suppress the nucleation and mobility of dislocations. Due to the substrate confinement, the deformation model was gradually changed from cracking (with homogeneous flow) to shear banding (with homogeneous flow). Eventually, fully-homogeneous flows occur with reducing the film thickness, and the deformation mechanism map is developed to expound the transition of the deformation mode. The brittle fracture with a high velocity originating from amorphous films leads to cleavage cracking on the surface of the HEA substrate. The thicker film has higher crack velocity and causes deeper cracks penetration into the substrate, reducing the substrate ductility.

36 MATERIALS SCIENCE↗

Rare-earth high entropy alloys with hexagonal close-packed structure

The formation of octonary DyErGdHoLuScTbY and senary DyGdHoLaTbY and ErGdHoLaTbY high-entropy alloys (HEAs) with the hexagonal close-packed (HCP) structure was reported in this study. Experiments using scanning electron microscopy and x-ray diffraction confirmed the single HCP solid solution in the as-cast state for these three HEAs if the presence of minor rare-earth oxides due to contamination from processing is ignored. The measured compressive yield stress values for these HEAs at room temperature are 245, 205, and 360 MPa for the ErGdHoLaTbY, DyGdHoLaTbY, and DyErGdHoLuScTbY HEAs, respectively. As a result, the corresponding solid solution strengthening contributions for these HEAs were estimated using a simple elastic model, and the resulting contributions were 28 MPa, 27 MPa, and 42 MPa for the three aforementioned HEAs.

36 MATERIALS SCIENCE↗

Microstructure and fracture properties of open-cell porous Ti-6Al-4V with high porosity fabricated by electron beam melting

Highlights: • The Ti-6Al-4V foams with 80% high porosity are prepared by electron beam melting. • The ligament width appears to play the major role for mechanical properties. • The work of fracture is a linear function of ligament width and roughness/width ratio. - Abstract: The open-cell porous Ti-6Al-4V structure with high porosity, intended to be applied as replacement for human cancellous bone, were fabricated by electron beam melting (EBM). Computer aided design (CAD) was applied to design porous structures using the same unit cell with different unit cell sizes from 2.5 to 4 mm, different ligament widths from 600 to 900 μm, and different pore sizes from 1200 to 1800 μm, in order to achieve high porosity of 80% in avoiding the stress shielding effect. In comparison with the CAD designs and the EBM samples, there were minor discrepancies in terms of pore size and ligament width, mainly a result of melting pool. The measured data on the Young's modulus and yield strength of the EBM porous samples can be predicted by the Gibson and Ashby model. All samples with high porosity were found to match well with cancellous bone, with Young's modulus of 2 GPa and yield stress of 31 MPa, effective to diminish the risk of stress shielding effect. For porous EBM sample with high 80% porosity, the work of fracture can increase from 15.9 to 47.6 kJ/m{sup 2} with increasing ligament width from 600 to 900 μm.

36 MATERIALS SCIENCE↗

Guiding and collimating fast electron beam by the quasi-static electromagnetic field array

A guidance and collimation scheme for fast electron beam in a traverse periodic quasi-static electromagnetic field array is proposed with the semi-analytic method and the particle-in-cell simulation. The sheath electric fields on the surfaces of nanowires and the magnetic fields around the nanowires form a traverse periodic quasi-static electromagnetic field array. Therefore, most of the fast electrons are confined at the nanowire surfaces and transport forward. More importantly, due to the divergent property of the beams, the magnitudes of the generated fields decrease with the target depth. The lateral momenta of the electrons convert into the forward momenta through Lorenz force, and they cannot recover their initial values. Therefore, the fast electrons can be guided and collimated efficiently in the gaps between the nanowires. In our particle-in-cell simulations, the observed guiding efficiency exceeds 80% compared with the reference target.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Generation of low-divergence megaelectronvolt ion beams from thin foil irradiated with an ultrahigh-contrast laser

Megaelectronvolt (MeV) ion beams with low divergence (10 Degree-Sign ) are experimentally generated from a thin foil irradiated by an ultrahigh-contrast laser at a peak intensity of {approx}10{sup 18} W/cm{sup 2}. The high-contrast ({approx}10{sup 11}) laser is obtained with a pulse cleaner based on noncollinear optical-parametric amplification and second-harmonic generation processes. The effects of the foil density, foil thickness, as well as the density gradients at the front and back sides of the foil are investigated with two-dimensional particle-in-cell simulations. The beam parameters of maximum energy and divergence strongly depend on the density gradients at the back side of the foil.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Simplified calculation of solar flux distribution on the side wall of cylindrical cavity solar receivers

A simple solar flux calculation algorithm for a cylindrical cavity type solar receiver has been developed and implemented on an IBM PC-AT. Using cone optics, the contour error method is utilized to handle the slope error of a paraboloidal concentrator. The flux distribution on the side wall is calculated by integration of the energy incident from cones emanating from all the differential elements on the concentrator. The calculations are done for any set of dimensions and properties of the receiver and the concentrator, and account for any spillover on the aperture plate. The results of this algorithm compared excellently with those predicted by more complicated programs. Because of the utilization of axial symmetry and overall simplification, it is extremely fast. It can be esily extended to other axisymmetric receiver geometries.

Bhandari, P.↗

Lightweight composite mirror analysis and testing

The Jet Propulsion Laboratory InterDisciplinary Model for precision composite structures is described along with the HAVOC composite computer code used to study laminate mirror facesheets. The composite mirror panel thermal behavior is described in addition to structural and optical characteristics. Environmental mirror performance testing and performance test/prediction correlation are covered.

Helms, R. G.↗

Large Deployable Reflector (LDR) thermal characteristics

The thermal support group, which is part of the lightweight composite reflector panel program, developed thermal test and analysis evaluation tools necessary to support the integrated interdisciplinary analysis (IIDA) capability. A detailed thermal mathematical model and a simplified spacecraft thermal math model were written. These models determine the orbital temperature level and variation, and the thermally induced gradients through and across a panel, for inclusion in the IIDA.

Miyake, R. N.↗

Large deployable reflector thermal characteristics in low earth orbits

Preliminary results are presented from the development of a thermal analytical tool capable of analyzing the orbital thermal characteristics of a Large Deployable Reflector (LDR) spaceborne astronomical instrument for observations in the 30-micron to 1-mm range. This LDR thermal analytical tool is a 9X6-node reflector thermal model to be used in conjunction with the thermal analyzer program SINDA, as well as the orbital heat flux program TRASYS for the computation of solar and IR radiation and orbit-related input data.

Wu, Y. C.↗

Solar dynamic heat receiver thermal characteristics in low earth orbit

A simplified system model is under development for evaluating the thermal characteristics and thermal performance of a solar dynamic spacecraft energy system's heat receiver. Results based on baseline orbit, power system configuration, and operational conditions, are generated for three basic receiver concepts and three concentrator surface slope errors. Receiver thermal characteristics and thermal behavior in LEO conditions are presented. The configuration in which heat is directly transferred to the working fluid is noted to generate the best system and thermal characteristics. as well as the lowest performance degradation with increasing slope error.

Wu, Y. C.↗

The development of an advanced generic solar dynamic heat receiver thermal model

An advanced generic solar dynamic heat receiver thermal model under development which can analyze both orbital transient and orbital average conditions is discussed. This model can be used to study advanced receiver concepts, evaluate receiver concepts under development, analyze receiver thermal characteristics under various operational conditions, and evaluate solar dynamic system thermal performances in various orbit conditions. The model and the basic considerations that led to its creation are described, and results based on a set of baseline orbit, configuration, and operational conditions are presented to demonstrate the working of the receiver model.

Wu, Y. C.↗

Site-Specific Research Conducted in Support of the Salton Sea Solar Pond Project - FY 1982 Report

The design and operation of a salt-gradient solar pond power plant at the Salton Sea presents problems not encountered at small research ponds that were built in the United States. The specific characteristics of the Salton Sea site and the desire to construct the pond using the local clay as a sealant represent major deviations from previous solar pond experience. The site-specific research in support of the plant design is described. The research activity included validation of the spectrophotometric light transmission measurement technique, a search for options for clarifying the turbid and colored water of the Salton Sea, development of water clarification specifications in terms common to industry practice, quantification of gas production from microbiological reactions in the ground, a determination of the combined effects of temperature and salinity on the permeation of the local clays, and a preliminary evaluation of material corrosion.

French, R. L.↗

Solar pond power plant feasibility study for Davis, California

The feasibility of constructing a solar pond power plant at Davis, California was studied. Site visits, weather data compilation, soil and water analyses, conceptual system design and analyses, a material and equipment market survey, conceptual site layout, and a preliminary cost estimate were studied. It was concluded that a solar pond power plant is technically feasible, but economically unattractive. The relatively small scale of the proposed plant and the high cost of importing salt resulted in a disproportionately high capital investment with respect to the annual energy production capacity of the plant. Cycle optimization and increased plant size would increase the economical attractiveness of the proposed concept.

Wu, Y. C.↗

A study of central cryogenic cooling system for the comet rendezvous spacecraft

Several science instruments required temperatures between 100 K and 120 K on a proposed Halley Flyby, Tempel-2 Rendezvous Mission. Significant features of the thermal environment are a large variation in heliocentric as well as comet distance, very large solar panels for a Solar Electric Propulsion stage, and the comet dust environment. The best cooling is achieved by one central radiative cooler connected by insulated cryogenic heat pipes to the instruments. The conceptual design is of a single-stage rectangular shielded radiator deployed on a boom some distance from the spacecraft bus and solar panels. Thermal modeling determined sensitivity to solar and comet distance and was used to optimize cooler geometry.

Salazar, R. P.↗

Solar receiver performance of point focusing collector system

The solar receiver performance of cavity receivers and external receivers used in dispersed solar power systems was evaluated for the temperature range 300-1300 C. Several parameters of receiver and concentrator are examined. It was found that cavity receivers are generally more efficient than external receivers, especially at high temperatures which require a large heat transfer area. The effects of variation in the ratio of receiver area to aperture area are considered.

Wu, Y. C.↗

Comparative performance of solar thermal power generation concepts

A performance comparison is made between the central receiver system (power tower) and a distributed system using either dishes or troughs and lines to transport fluids to the power station. These systems were analyzed at a rated capacity of 30 MW of thermal energy delivered in the form of superheated steam at 538 C (1000 F) and 68 atm (1000 psia), using consistent weather data, collector surface waviness, pointing error, and electric conversion efficiency. The comparisons include technical considerations for component requirements, land utilization, and annual thermal energy collection rates. The relative merits of different representative systems are dependent upon the overall conversion as expressed in the form of performance factors in this paper. These factors are essentially indices of the relative performance effectiveness for different concepts based upon unit collector area. These performance factors enable further economic tradeoff studies of systems to be made by comparing them with projected production costs for these systems.

Wen, L.↗