Search NASA⌕ Search

Engineering topics

Wukitch, S. J.

Publications and source records attributed to Wukitch, S. J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The role of RF-induced E×B flows in the mitigation of scrape-off-layer convective transport during ion cyclotron resonance heating

Abstract While multiple experiments have reported a decrease in intermittent fluctuations in the far Scrape-Off-Layer (SOL) during ion cyclotron resonance heating (Antar et al 2010 Phys. Rev. Lett. 105 165001, Li et al 2022 Nucl. Eng. Technol. 54 207–19, Antar et al 2012 Nucl. Fusion 52 103005), the physical mechanism behind this observation has not been fully established yet. In this work, we demonstrate, for the first time, a direct correlation between the amplitude of RF-induced E×B flows and turbulence suppression in the far SOL. Using the Gas Puff Imaging (GPI) diagnostic on Alcator C-Mod, we show again that Ion Cyclotron Range of Frequencies can significantly alter the flow in the SOL and introduce a shear layer in regions magnetically connected close to the antenna (Cziegler et al 2012 Plasma Phys. Control. Fusion 54 105019). With the 4-strap field-aligned antenna operated in dipole phasing, the ratio of the power coupled by the central two straps to the power coupled by the outer two straps was varied. The resulting RF-induced radial electric field magnitude thus varied, and we show that the impact on the far SOL turbulence correlates with the modified E×B velocity. We then apply a newly-developed blob tracking algorithm (Han et al 2022 Sci. Rep. 12 18142) to higher-resolution GPI videos in order to directly observe the process of blob shearing by RF-induced E×B flows. We show that the radially sheared poloidal flows act as a transport barrier by stretching, stopping, and destroying filaments, which is consistent with the observed difference in turbulence statistics.

Diab, R. (ORCID:0000000342065868)↗
DOE OSTI2023

Evaluation of the Abel inversion integral in O-mode plasma reflectometry using Chebyshev–Gauss quadrature

The Abel transform is often used to reconstruct plasma density profiles from O-Mode polarized reflectometry diagnostics. However, standard numerical trapezoidal evaluation of the Abel inversion integral can be computationally expensive for a large number of evaluation points, and an endpoint singularity exists on the upper-bound of the integral, which can result in an increased error. In this work, Chebyshev–Gauss quadrature is introduced as a new method to evaluate the Abel inversion integral for the problem of O-Mode plasma reflectometry. Here, the method does not require numerical evaluation of an integral singularity and is shown to have similar accuracy compared to existing methods while being computationally efficient.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Argon Pumpout by ICRF Waves in C-Mod L- and I-mode Plasmas

Pumpout of argon ions by ICRF waves has been observed in C-Mod deuterium L- and I-mode plasmas that had a substantial hydrogen fraction. The effect is manifested by a reduction of core argon x-ray brightness up to a factor of 90% on time scales of tens of milliseconds following injection of ICRF power. For Ar^16+, the pumpout is strongest for hydrogen minority concentrations between 0.25 and 0.4, when the ICRF waves are not expected to result in minority heating. Modeling with the TORIC code suggests that the pumpout process occurs when the H/D mode conversion layer overlaps with the 2nd harmonic impurity resonance layer. The magnitude of the argon pumpout is independent of ICRF power above an apparent threshold of ~500 kW, independent of electron density and appears to decrease as the plasma current is increased. Potential application as a heavy impurity control tool in reactors is discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Brazing characteristics, microstructure, and wettability of laser powder bed fusion additive manufactured GRCop-84 compared to CuCrZr and OFC, and brazing to titanium-zirconium-molybdenum alloy limiters

Laser Powder Bed Fusion (L-PBF) of Glenn Research Copper 84 (GRCop-84), a Cr 2 Nb (8 at. % Cr, 4 at. % Nb) precipitation hardened alloy, produces a fully dense, high conductivity alloy with a yield strength of 500 MPa and ultimate tensile strength (UTS) of 740 MPa with 20% elongation; superior to other competing copper alloys. Braze wetting characteristics of GRCop-84 with Ag-Cu-X, and Au-Cu brazes were similar to CuCrZr, but less than oxygen free copper. No difference in wetting was observed between infill and surface contour areas in L-PBF GRCop-84. Wet sanding to 240 grit (R a =0.24 µm) was considered the optimal surface condition. Silver diffusing through GRCop-84 depleted Cr 2 Nb precipitates from the copper grain and deposited agglomerations of coarsened precipitates within silver-rich regions of intergranular diffusion once a density threshold was reached. Microstructure modification was minimized with 50Au-50Cu braze implying that silver caused precipitate coarsening and agglomeration, and not high temperature exposure. Coarsened precipitates were observed on the surface within braze pools implying a contribution to braze wetting. Palcusil-25, Ticusil, CuSil-ABA, and 50Au-50Cu brazes were suitable for brazing to unplated Titanium-Zirconium-Molybdenum (TZM), while sulfamate nickel plating to allows wetting with CuSil or other non-active brazes. Additionally, vacuum brazing techniques were developed to join a 1 mm thick layer of TZM to the front of additive manufactured GRCop-84 waveguides considering the brazing characteristics of both GRCop-84, TZM, and internal stress from the difference in coefficient in thermal expansion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Argon pumpout by ICRF waves in C-Mod L- and I-mode plasmas

Pumpout of argon ions by ICRF waves has been observed in C-Mod deuterium L- and I-mode plasmas that had a substantial hydrogen fraction. The effect is manifested by a reduction of core argon x-ray brightness up to a factor of 90% on time scales of tens of milliseconds following injection of ICRF power. For Ar 16+ , the pumpout is strongest for hydrogen minority concentrations between 0.25 and 0.4, when the ICRF waves are not expected to result in minority heating. Modeling with the TORIC code suggests that the pumpout process occurs when the H/D mode conversion layer overlaps with the 2nd harmonic impurity resonance layer. Here, the magnitude of the argon pumpout is independent of ICRF power above an apparent threshold of ~500 kW, independent of electron density and appears to decrease as the plasma current is increased. Potential application as a heavy impurity control tool in reactors is discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

The geometry of the ICRF-induced wave–SOL interaction. A multi-machine experimental review in view of the ITER operation

As a part of ITPA-Integrated Operational Scenario activities, this contribution reviews recent experimental characterizations of radio-frequency (RF)-induced scrape-off layer (SOL) modifications of various tokamaks worldwide and of the LArge Plasma Device at UCLA. The phenomenology, as observed using a large variety of measurement techniques, is consistent with expectations from RF sheath rectification. Emphasis is then put on the complex three-dimensional (3D) spatial patterns of the RF–SOL interaction, in relation to the magnetic topology and the spatial distribution of RF currents over the metallic structures surrounding the RF wave launchers. Dependence on the local plasma parameters in the antenna vicinity is also briefly addressed. The final part discusses implications for future devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Fracture characteristics and heat treatment of laser powder bed fusion additively manufactured GRCop-84 copper

Laser Powder Bed Fusion (LPBF) of Glenn Research Copper 84 (GRCop-84), a Cr 2 Nb (8 at. % Cr, 4 at. % Nb) precipitation hardened alloy, produces a fully dense high conductivity alloy with a yield strength of 500 MPa and ultimate tensile strength (UTS) of 740 MPa, superior to other competing copper alloys, and 20% elongation at fracture for material stressed perpendicular to the build direction. The high thermal stability of the Cr 2 Nb precipitate in the copper matrix reduces coarsening and maintains a 300 MPa yield, 520 MPa UTS and 26% elongation after a 900 °C, 5-h heat treatment, while a 3 h 450 °C heat treatment increases yield to 810 MPa, UTS to 970 MPa with 9% elongation at fracture, for samples stressed perpendicular to the build direction. Tensile strength anisotropy based on print direction was attributed to internal stress and columnar grain formation. Void nucleation during tensile fracture was initiated by brittle fracture of precipitate particles within the copper matrix. Fracture cusps contain matching precipitate fragment geometry on opposing sides located near the cusp center in at least 80% of fracture cusps. An optimal precipitate size of 100 nm is predicted for maximum tensile strength from precipitates on fracture surfaces, while tensile testing with varying heat treatments shows maximum strength with 100 nm and smaller precipitates. Cr2Nb precipitates are shown to transition between polycrystalline and monocrystalline structures at high temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High Field Side Launch of Lower Hybrid Waves: A Scoping Study for ADX

Launching lower hybrid (LH) waves from the high field side (HFS) of a tokamak offers significant advantages over low field side (LFS) launch with respect to both wave physics and plasma material interactions (PMI). The higher magnetic field opens the window between wave accessibility and the condition for strong electron Landau damping, allowing LH waves from the HFS to penetrate into the core of a burning plasma, while waves launched from the LFS are restricted to the periphery of the plasma. The lower parallel refractive index (n) of waves launched from the HFS yields a higher current drive efficiency as well. The absence of turbulent heat and particle fluxes on the HFS, particularly in double null configuration, makes it the ideal location to minimize PMI damage to the antenna structure. The quiescent SOL also eliminates the need to couple LH waves across a long distance to the separatrix, as the antenna can be located close to plasma without risking damage to the structure.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Overview of the fusion nuclear science facility, a credible break-in step on the path to fusion energy

The Fusion Nuclear Science Facility (FNSF) is examined here as part of a two step program from ITER to commercial power plants. This first step is considered mandatory to establish the materials and component database in the real fusion in-service environment before proceeding to larger electricity producing facilities. The FNSF can be shown to make tremendous advances beyond ITER, toward a power plant, particularly in plasma duration and fusion nuclear environment. A moderate FNSF is studied in detail, which does not generate net electricity, but does reach the power plant blanket operating temperatures. The full poloidal Dual Coolant Lead Lithium (DCLL) blanket is chosen, with alternates being the Helium Cooled Lead Lithium (HCLL) and Helium Cooled Ceramic Breeder/Pebble Bed (HCCB/PB). Several power plant relevant choices are made in order to follow the philosophy of targeted technologies. Any fusion core component must be qualified by fusion relevant neutron testing and highly integrated non-nuclear testing before it can be installed on the FNSF in order to avoid the high probability of constant failures in a plasma-vacuum system. A range of missions for the FNSF, or any fusion nuclear facility on the path toward fusion power plants, are established and characterized by several metrics. A conservative physics strategy is pursued to accommodate the transition to ultra-long plasma pulses, and parameters are chosen to represent the power plant regime to the extent possible. An operating space is identified, and from this, one point is chosen for further detailed analysis, with R = 4.8 m, a = 1.2 m, IP = 7.9 MA, BT = 7.5 T, βN Gr = 0.9, fBS = 0.52, q95 = 6.0, H98 ∼1.0, and Q = 4.0. The operating space is shown to be robust to parameter variations. A program is established for the FNSF to show how the missions for the facility are met, with a He/H, a DD and 5 DT phases. The facility requires ∼25 years to complete its DT operation, including 7.8 years of neutron production, and the remaining spent on inspections and maintenance. The DD phase is critical to establish the ultra-long plasma pulse lengths. The blanket testing strategy is examined, and shows that many sectors have penetrations for heating and current drive (H/CD), diagnostics, or Test Blanket Modules (TBMs). The hot cell is a critical facility element in order for the FNSF to perform its function of developing the in-service material and component database. The pre-FNSF R&D is laid out in terms of priority topics, with the FNSF phases driving the time-lines for R&D completion. A series of detailed technical assessments of the FNSF operating point are reported in this issue, showing the credibility of such a step, and more detailed emphasis on R&D items to pursue. These include nuclear analysis, thermo-mechanics and thermal-hydraulics, liquid metal thermal hydraulics, transient thermo-mechanics, tritium analysis, maintenance assessment, magnet specification and analysis, materials assessments, core and scrape-off layer (SOL)/divertor plasma examinations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

High Field Side Launch of RF Waves: A New Approach to Reactor Actuators

Launching radio frequency (RF) waves from the high field side (HFS) of a tokamak offers significant advantages over low field side (LFS) launch with respect to both wave physics and plasma material interactions (PMI). For lower hybrid (LH) waves, the higher magnetic field opens the window between wave accessibility and the condition for strong electron Landau damping, allowing LH waves from the HFS to penetrate into the core of a burning plasma, while waves launched from the LFS are restricted to the periphery of the plasma. The lower of waves absorbed at higher yields a higher current drive efficiency as well. In the ion cyclotron range of frequencies (ICRF), HFS launch allows for direct access to the mode conversion layer where mode converted waves absorb strongly on thermal electrons and ions, thus avoiding the generation of energetic minority ion tails. The absence of turbulent heat and particle fluxes on the HFS, particularly in double null configuration, makes it the ideal location to minimize PMI damage to the antenna structure. The quiescent SOL also eliminates the need to couple LH waves across a long distance to the separatrix, as the antenna can be located close to plasma without risking damage to the structure. Improved impurity screening on the HFS will help eliminate the long-standing issues of high Z impurity accumulation with ICRF.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Alcator C-Mod: Research in support of ITER and steps beyond

This paper presents an overview of recent highlights from research on Alcator C-Mod. Significant progress has been made across all research areas over the last two years, with particular emphasis on divertor physics and power handling, plasma-material-interaction studies, ELM-suppressed pedestal dynamics, core transport and turbulence, and RF heating and current drive utilizing Ion Cyclotron and Lower Hybrid tools. Specific results of particular relevance to ITER include: inner wall SOL transport studies that have led, together with results from other experiments, to the change of the detailed shape of the inner wall in ITER; runaway electron studies showing that the critical electric field required for runaway generation is much higher than predicted from collisional theory; core tungsten impurity transport studies reveal that tungsten accumulation is naturally avoided in typical C-Mod conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Overview of the SPARC tokamak

The SPARC tokamak is a critical next step towards commercial fusion energy. SPARC is designed as a high-field ( $B_0 = 12.2$ T), compact ( $R_0 = 1.85$ m, $a = 0.57$ m), superconducting, D-T tokamak with the goal of producing fusion gain $Q>2$ from a magnetically confined fusion plasma for the first time. Currently under design, SPARC will continue the high-field path of the Alcator series of tokamaks, utilizing new magnets based on rare earth barium copper oxide high-temperature superconductors to achieve high performance in a compact device. The goal of $Q>2$ is achievable with conservative physics assumptions ( $H_{98,y2} = 0.7$ ) and, with the nominal assumption of $H_{98,y2} = 1$ , SPARC is projected to attain $Q \approx 11$ and $P_{\textrm {fusion}} \approx 140$ MW. SPARC will therefore constitute a unique platform for burning plasma physics research with high density ( $\langle n_{e} \rangle \approx 3 \times 10^{20}\ \textrm {m}^{-3}$ ), high temperature ( $\langle T_e \rangle \approx 7$ keV) and high power density ( $P_{\textrm {fusion}}/V_{\textrm {plasma}} \approx 7\ \textrm {MW}\,\textrm {m}^{-3}$ ) relevant to fusion power plants. SPARC's place in the path to commercial fusion energy, its parameters and the current status of SPARC design work are presented. This work also describes the basis for global performance projections and summarizes some of the physics analysis that is presented in greater detail in the companion articles of this collection.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Nuclear response of additive manufactured GRCop-84 copper for use in Lower hybrid launchers in a fusion environment

Recent advances in selective laser melting (SLM) 3D printing technology allow additive manufacture of lower hybrid current drive (LHCD) RF launchers from a new material, Glenn Research Copper 84 (GRCop-84), a Cr 2 Nb (8 at. % Cr, 4 at. % Nb) precipitation hardened alloy, in configurations unachievable with conventional machining. Tensile strength and thermal conductivity are compared to other competing high conductivity copper alloys for fusion use. Swelling and conductivity at 100 DPA when exposed to the Hanford Fast Flux Test Facility neutron spectrum is predicted in the 1–2 % and 65-70% IACS range, respectively, by comparison to copper alloys with similar precipitate and grain size. Finally, self-similar ion irradiation of a GRCop-84 target at 430 °C to 20 DPA resulted in no noticeable void formation in FIB cross sections or TEM lamella.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗