Search NASA⌕ Search

Engineering topics

Wurster, K. E.

Publications and source records attributed to Wurster, K. E..

15 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Aerodynamic heating environment definition/thermal protection system selection for the HL-20

Definition of the aerothermal environment is critical to any vehicle such as the HL-20 Personnel Launch System that operates within the hypersonic flight regime. Selection of an appropriate thermal protection system design is highly dependent on the accuracy of the heating-environment prediction. It is demonstrated that the entry environment determines the thermal protection system design for this vehicle. The methods used to predict the thermal environment for the HL-20 Personnel Launch System vehicle are described. Comparisons of the engineering solutions with computational fluid dynamic predictions, as well as wind-tunnel test results, show good agreement. The aeroheating predictions over several critical regions of the vehicle, including the stagnation areas of the nose and leading edges, windward centerline and wing surfaces, and leeward surfaces, are discussed. Results of predictions based on the engineering methods found within the MINIVER aerodynamic heating code are used in conjunction with the results of the extensive wind-tunnel tests on this configuration to define a flight thermal environment. Finally, the selection of the thermal protection system based on these predictions and current technology is described.

Wurster, K. E.↗
NASA NTRS1987

An aerothermodynamic study of slender conical vehicles

A numerical study was performed to assess the applicability of some current techniques which can be used for aerothermal predictions over slender spherically blunted cones. Predictions using a viscous-shock-layer method and several engineering approaches were compared with experimental results from flight and ground-based tests, with each other, and with other detailed results. Good agreement was obtained in comparisons with laminar and turbulent heating data from the Reentry F flight vehicle and with the wind-tunnel data. In particular, the viscous-shock-layer method was shown to yield excellent comparisons and should be useful in providing detailed flowfield and surface values for slender blunted cones. Additional predictions were obtained with these methods for two 5-deg half-angle cones with different nose radii to illustrate the effects of nose bluntness and angle of attack on drag and heat transfer. These results demonstrate the benefit of nose blunting with respect to heating and drag for laminar and transitional flow at zero-lift conditions and the benefit of heating reduction at angle of attack. Detailed comparison of the engineering code predictions with the viscous-shock-layer results for these additional cases generally showed good agreement except for the laminar prodictions at angle of attack on the forward cone surface. Nonequilibrium calculations at 0-deg angle of attack showed that substantial benefits of low surface catalysis existed only in the nose-dominated region.

Thompson, R. A.↗
NASA NTRS1985

Definition of an entry research vehicle

Within the last year, there has been a growing interest in technology which would support the development of vehicles which can maneuver in the atmosphere while returning from orbit and vehicles which can fly in the atmosphere at hypersonic speeds for sustained periods of time. This rebirth of interest in hypersonics is partly a result of a developing awareness of the potential benefits which can be derived from vehicles with capability to operate between the limits of existing aircraft and spacecraft. Examples of the types of maneuvers which are projected for this new class of vehicles are presented. Challenges provided by the considered maneuvers are summarized, taking into account a synergetic or atmospheric plane change. The plane change maneuver will require a Thermal Protection System (TPS). Attention is given to the definition of a Shuttle launched entry research vehicle experiment. Details regarding the synergetic plane change are considered along with the maneuvering entry, vehicle heating, and experiments and instrumentation.

Freeman, D. C.↗
NASA NTRS1985

Orbit on demand - Structural analysis finds vertical launchers weigh less

Structural considerations arising from favored design concepts for the next generation on-demand launch vehicles are explored. The two emerging concepts are a two stage fully reusable vertical take-off vehicle (V-2) and a horizontal take-off, two stage subsonic boost launch vehicle (H-2-Sub). Both designs have an 1100 n. mi. cross-range capability, with the V-2 orbiter having small wings with winglets for hypersonic trim and the H-2-Sub requiring larger, swept wings. The rockets would be cryogenic, while airbreathing initial boosters would be either turbofans, turbojets and/or ramjets. Dynamic loading is lower in the launch of a V-2. The TPS is a critical factor due to thinner leading edges than on the Shuttle and may require heat-pipe cooling. Airframe structures made of metal matrix composites have passed finite element simulations of projected loads and can now undergo proof-of-concept tests, although whisker-reinforced materials may be superior once long-whisker technology is developed.

Taylor, A. H.↗
NASA NTRS1984

An experimental investigation of surface pressure measurements on an advanced winged entry vehicle at Mach 10

Surface pressure measurements have been made at Mach 10 in air on an instrumented 0.006-scale model of an advanced (control configured) winged entry vehicle. The tests were conducted in the Langley Continuous Flow Hypersonic Tunnel. Data were obtained at 83 surface pressure stations, which include locations on the lower and upper surface centerlines, spanwise positions along the lower and upper surfaces of the wing, the lower surface of the body flap, and radial locations on the fuselage. Data were obtained for angles of attack ranging from zero to 40 deg, sideslip angles of -2 deg to +5 deg, Reynolds numbers of 0.5, 1.0, and 2.0 million per foot, and body-flap deflections of zero, 10, and 20 deg. Test conditions and orifice locations were chosen to correspond directly with those for the heat transfer measurements previously reported on the same configuration. Comparison of windward symmetry plane data with predictions based upon an approximate engineering method was found to yield reasonable agreement for angles of attack from 20 to 40 deg. The leeward surface pressure data were observed to be roughly an order of magnitude lower than the corresponding windward data. At low angles of attack, regions of high pressure were noted on the windward wing surface. The result is attributed to vortical action or shock impingement. High pressures were also measured on the deflected body flap, a critical region for this type of vehicle. Reynolds number effects were found to be insignificant.

Wurster, K. E.↗
NASA NTRS1983

An experimental heat-transfer investigation of an advanced winged entry vehicle at Mach 10

Heat-transfer measurements have been made at Mach 10 in air on an instrumented 0.006-scale model of an advanced winged entry vehicle. Data were obtained at 83 thermocouple stations which include locations on the lower and upper surface centerlines, spanwise positions along the lower and upper surfaces of the wing, the lower surface of the body flap, and radial locations on the fuselage. Data were obtained for angles of attack ranging from 0 to 45 deg, sideslip angles of + or - 2 deg, Reynolds numbers of 0.5, 1.0 and 2.0 million per foot, and body-flap deflections of 0, 10, and 20 deg. The data generally indicate increased windward heating and decreased leeside heating with increased angle of attack, significantly increased body-flap heating with deflection angle, and minor variations in heating with sideslip, increasing in magnitude with angle of attack. Windward centerline data are shown to be in fair agreement with results of predictions based on an approximate engineering method.

Wurster, K. E.↗
NASA NTRS1981

Anatomy of an entry vehicle experiment

The anatomy and evolution of a simple small-scale unmanned entry vehicle is described that is delivered to orbit by the shuttle and entered into the atmosphere from orbit to acquire flight data to improve our knowledge of boundary-layer behavior and evaluate advanced thermal protection systems. The anatomy of the experiment includes the justification for the experiments, instrumentation, configuration, material, and operational needs, and the translation of these needs into a configuration, weight statement, aerodynamics, program cost, and trajectory. Candidates for new instrumentation development are also identified for nonintrusive measurements of the boundary-layer properties.

Eide, D. G.↗
NASA NTRS1981

An assessment of the impact of transition on advanced winged entry vehicle thermal protection system mass

This study examines the impact of turbulent heating on thermal protection system (TPS) mass for advanced winged entry vehicles. Four basic systems are considered: insulative, metallic hot structures, metallic standoff, and hybrid systems. TPS sizings are performed using entry trajectories tailored specifically to the characteristics of each TPS concept under consideration. Comparisons are made between systems previously sized under the assumption of all laminar heating and those sized using a baseline estimate of transition and turbulent heating. The relative effect of different transition criteria on TPS mass requirements is also examined. Also investigated are entry trajectories tailored to alleviate turbulent heating. Results indicate the significant impact of turbulent heating on TPS mass and demonstrate the importance of both accurate transition criteria and entry trajectory tailoring.

Wurster, K. E.↗
NASA NTRS1980

Mass reduction for advanced winged entry vehicles through integrated thermostructural-trajectory design

This study examines the impact of aerothermo-structure design integration on thermal protection system (TPS) mass for advanced winged entry vehicles. Four basic categories of TPS are considered: external insulation, metallic hot structures, metallic standoff, and hybrid systems. A variety of concepts that fit in these basic categories are examined. Entry trajectories tailored specifically to the characteristics of each TPS concept are generated. An aerodynamic heating program is used with the appropriately tailored trajectories to determine the centerline TPS requirements for each concept. Included in the investigation is the impact on the combined TPS-structure mass of structural materials which maintain their integrity to higher temperatures. Results indicate that significant mass reduction can be realized through appropriate aerothermo-structure design integration. An assessment is made of the relative merits of the TPS/structure/trajectory combinations considered in the study.

Wurster, K. E.↗
NASA NTRS1979

Technology and operational considerations for low-heat-rate trajectories

A broad parametric study which examines several critical aspects of low-heat-rate entry trajectories is performed. Low planform loadings associated with future winged earth-entry vehicles coupled with the potential application of metallic thermal protection systems (TPS) suggest that such trajectories are of particular interest. Studied are three heating conditions - reference, stagnation, and windward centerline, for both laminar and turbulent flow; configuration-related factors including planform loading and hypersonic angle of attack; and mission-related factors such as cross-range and orbit inclination. Results indicate benefits in the design of TPS to be gained by utilizing moderate angles of attack as opposed to high-lift coefficient, high angles of attack, during entry. An assessment of design and technology implications is made.

Wurster, K. E.↗
NASA NTRS1978

Propulsion options for space-based orbital transfer vehicles

A concept for a lightweight space-based orbital transfer vehicle (OTV) featuring thin, spherical, pressure-designed aluminum liquid-oxygen and liquid-hydrogen tanks and a truss structure of composite materials is used as a baseline design for a large-cargo OTV. Vehicle sizing, fleet analysis, and parametric cost analysis are used to evaluate the effects of engine technology, vehicle staging, and high-thrust versus low-thrust transfer. Results indicate that Earth-to-orbit launch costs and OTV engine performance are strong drivers in orbital transportation cost and that there is no significant benefit in staging vehicles. At the low values of Earth-to-orbit cost representative of advanced launch vehicles, low-thrust and high-thrust OTV's are competitive.

Rehder, J. J.↗
NASA NTRS1978

The effect of technology advancements on the comparative advantages of electric versus chemical propulsion for a large cargo orbit transfer vehicle

Techniques for sizing electrically or chemically propelled orbit transfer vehicles and analyzing fleet requirements are used in a comparative analysis of the two concepts for various levels of traffic to geosynchronous orbit. The vehicle masses, fuel requirements, and fleet sizes are determined and translated into launch vehicle payload requirements. Technology projections beyond normal growth are made and their effect on the comparative advantages of the concepts is determined. A preliminary cost analysis indicates that although electric propulsion greatly reduces launch vehicle requirements substantial improvements in the cost and reusability of power systems must occur to make an electrically propelled vehicle competitive.

Rehder, J. J.↗