Search NASA⌕ Search

Engineering topics

Xiao, Chuanxiao

Publications and source records attributed to Xiao, Chuanxiao.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Metastability and Degradation of CdTe Solar Cells Investigated by nm-Scale Electrical Potential Imaging

We report on investigations of reversible metastability and irreversible degradation of MZO/CdSeTe/CdTe devices from the perspective of electric field across the device using Kelvin probe force microscopy (KPFM). The device showed reversible transitions between the light-soak state (LSS) with the best device efficiency and the dark-soak state (DSS) with an inferior efficiency. However, it showed an irreversible degradation state (DgS) driven by long-hour light soaking at an elevated temperature. The nm-scale KPFM electric field imaging on cross-sections of the devices revealed different anomalous electric field profiles. The electric field at the LSS exhibits a main peak inside the CdSeTe layer but not at the MZO/CdSeTe heterointerface, demonstrating that working junction of the device is a buried homojunction (BHJ). At the DSS, a second electric field peak was observed at the MZO/CdSeTe interface with a similar strength to the main BHJ, which probably caused the decrease in fill factor at the DSS. At the DgS, the electric field peak at the MZO/CdSeTe interface increased significantly and a third electric field was measured at the back contact of the device. Device modeling using COMSOL and in alignment with both the electric field and device current-voltage curves suggest that a slightly low n-doped CdSeTe in the region near the MZO/CdSeTe interface caused the BHJ, and that either a loss of MZO doping or increase of the conduction band offset spike due to long-term stress caused the fill factor-dominated degradation and the increased electric field near the MZO/CdSeTe interface at the DgS. The former, MZO doping decrease, is more plausible by referring the related literature.

BHJ↗
DOE OSTI2022

Surface reaction for efficient and stable inverted perovskite solar cells

We report perovskite solar cells (PSCs) with an inverted structure (often referred to as the p-i-n architecture) are attractive for future commercialization due to their easily scalable fabrication, reliable operation, and compatibility with a wide range of perovskite-based tandem device architectures. However, the power conversion efficiency (PCE) of p-i-n PSCs falls behind n-i-p (or normal) structure counterparts. This large performance gap could undermine efforts to adopt p-i-n architectures, despite their other advantages. Given the remarkable advances in perovskite bulk materials optimization over the past decade, interface engineering has become the most important strategy to push PSC performance to its limit. Here, we report a reactive surface engineering approach based on a simple post-growth treatment of 3-(Aminomethyl)pyridine (3-APy) on top of a perovskite thin film. First, the 3-APy molecule selectively reacts with surface FA+, reducing perovskite surface roughness and surface potential fluctuations associated with surface steps/terraces. Second, the reaction product on the perovskite surface decreases the formation energy of charged iodine-vacancies, leading to effective n-type doping with a reduced work function in the surface region. With this reactive surface engineering, the resulting p-i-n PSCs obtained a PCE over 25%, along with retaining 87% of the initial PCE after over 2400 h of one-sun operation at about 55 degrees C in air.

14 SOLAR ENERGY↗
DOE OSTI2022

LeTID-Affected Cells from a Utility-Scale Photovoltaic System Characterized by Deep Level Transient Spectroscopy

Photovoltaic modules from a utility-scale field experienced power loss by light- and elevated temperature-induced degradation (LeTID). Samples of one of the affected monocrystalline silicon cells were cored and extracted from the module packaging and encapsulation. One of the cell fragments was processed using a regeneration cycle of applying short-circuit-rated current in forward bias at 85 degrees C for 2 weeks, while the other fragment was kept in its outdoor-degraded LeTID state. Both samples were scribed to form 2-mm diameter isolated areas using a femtosecond-pulse-width laser micromachining system. Both isolated areas contained front grid line segments which were wire bonded to larger contact pads, and the samples were probed in a cryostat linked to a deep-level transient spectroscopy (DLTS) system. Using DLTS, a majority-carrier, hole-trap defect was detected on each sample with an activation energy of 0.42 eV. The LeTID-degraded sample, however, had a larger signal corresponding to a trap density of 1.1x10^13 cm-3, which was about five times larger than the 2.1x10^12 cm-3 trap density of the regenerated sample.

charge carrier lifetime↗
DOE OSTI2022

Tailoring electric dipole of hole-transporting material p-dopants for perovskite solar cells

We report Li-TFSI/t-BP are the most widely employed p-dopants for hole-transporting materials (HTMs) within the state-of-the-art perovskite solar cells (PSCs). The hygroscopicity and migration of these dopants, however, lead to devices with limited stability. To solve this problem, we report here on a diphenyl iodide cation and pentafluorophenyl boric acid anion-based dopant (DIC-PBA) with an oriented interfacial dipole moment as an alternative to Li-TFSI/t-BP. Theoretical and experimental data reveal that DIC-PBA exhibits deep doping of poly[bis(4-phenyl)(2,4,6-triMethylphenyl)aMine] (PTAA) and also creates p-doping of perovskite surface, which originates from ionic interactions-derived dipole arrangement that yields fast interfacial charge transport. The improved intrinsic stability of PSCs originates from the inhibition of dipole moment degeneration on the perovskite surface. Devices prepared with DIC-PBA yielded high efficiency of 22.86%, and the modules (aperture area: 33.2 cm 2 ) efficiency reached 19.13%. Importantly, the storage stability also significantly improved exceeding to 90% after aging 1,200 h under air ambient.

14 SOLAR ENERGY↗
DOE OSTI2022

Lead-Free Flexible Perovskite Solar Cells with Interfacial Native Oxide Have >10% Efficiency and Simultaneously Enhanced Stability and Reliability

Here we demonstrate an innovative compositional and interfacial engineering approach to achieve Pb-free flexible perovskite solar cells (f-PSCs) with an unprecedented combination of the highest efficiency reported to date (10.43%), together with enhanced operational stability and mechanical reliability. The key to this approach is alloying of an FASnI3 metal halide perovskite (MHP) thin film with Ge2+ to stabilize the Sn2+ oxidation state in the MHP, together with the use of a NiOx hole-transport layer. We show that this results in the in situ formation of a thin amorphous GeO2 native oxide layer at the NiOx/FASn0.9Ge0.1I3 interface. This layer not only passivates that critical interface but also enhances the interfacial mechanical bonding.

efficiency↗
DOE OSTI2022

Area-Scalable Zn 2 SnO 4 Electron Transport Layer for Highly Efficient and Stable Perovskite Solar Modules

The development of a scalable chemical bath deposition (CBD) process facilitates the realization of electron-transporting layers (ETLs) for large-area perovskite solar modules (PSMs). In this work, a method to prepare a uniform and scalable thick Zn 2 SnO 4 ETL by CBD, which yielded high-performance PSMs, is reported. This Zn 2 SnO 4 ETL exhibits excellent electrical properties and enhanced optical transmittance in the visible region. Moreover, the Zn 2 SnO 4 ETL influences the perovskite layer formation, yielding enhanced crystallinity, increased grain size, and a smoother surface, thus facilitating electron extraction and collection from the perovskite to the ETL. Zn 2 SnO 4 thereby yields PSMs with a remarkable photovoltaic performance, low hysteresis index, and high device reproducibility. The champion PSM exhibited a power conversion efficiency (PCE) of 22.59%, being among the highest values published so far. In addition, the CBD Zn 2 SnO 4 -based PSMs exhibit high stability, retaining more than 88% of initial efficiency over 1000 h under continuous illumination. This demonstrates that CBD Zn 2 SnO 4 is an appropriate ETL for high-efficiency PSMs and a viable new process for their industrialization.

17 WIND ENERGY↗
DOE OSTI2022

Light- and Elevated-Temperature-Induced Degradation-Affected Silicon Cells From a Utility-Scale Photovoltaic System Characterized by Deep-Level Transient Spectroscopy

Photovoltaic modules from a utility-scale field experienced power loss by light- and elevated-temperature-induced degradation (LeTID). Samples from the affected monocrystalline silicon cells are cored and extracted from the module packaging and then laser-scribed to form 2-mm diameter isolated areas. Using deep-level transient spectroscopy, a majority-carrier, hole-trap defect with an activation energy of 0.42 eV is detected on degraded and regenerated samples. The LeTID-degraded sample, however, has a larger signal corresponding to a trap density of 1.1 x 10 13 cm -3 , which is about five times larger than the 2.1 x 10 12 cm -3 trap density of the regenerated sample. An increase in filling pulse time from 50 u s to 20 ms shows a slight decrease in activation energy from 0.42 to 0.36 eV suggesting that the defect level may consist of a band of energy states where shallower states continue to fill with long filling times. The capture rate of the defect is directly measured using an increasing series of filling pulsewidths in 15 to 125 ns range. This leads to a measured capture cross section of 5.1 x 10 -17 cm 2 , and using an approximate defect density of 10 13 cm -3 , the majority-carrier-hole lifetime related to this defect is approximately 100 u s when in the LeTID-degraded state.

charge carrier lifetime↗
DOE OSTI2022

Electrical Potential Investigation of Reversible Metastability and Irreversible Degradation of CdTe Solar Cells

In this paper, we report on the stability of CdTe devices with a structure of TCO/MZO/CdSeTe/CdTe/back-contact. The device showed reversible transitions between the light-soak state (LSS) with the best device efficiency and the dark-soak state (DSS) with an inferior efficiency. However, it showed an irreversible degradation state (DgS) driven by long-hour light soaking at an elevated temperature. We have investigated transitions between these three states from the perspective of the electric field by nm-resolution potential imaging across the devices using Kelvin probe force microscopy (KPFM). The results exhibit different anomalous electric field profiles. At the LSS, the electric field exhibits a main peak inside the CdSeTe layer instead of the MZO/CdSeTe heterointerface, illustrating a buried homojunction (BHJ) of the device. At the DSS, a large electric field peak at the MZO/CdSeTe interface was measured, which probably resulted in the inferior fill factor at the DSS. At the DgS, the electric field peak at the MZO/CdSeTe interface increased further and a third electric field was measured at the back contact of the device. Device modeling using COMSOL software, in alignment with both the electric field and device current-voltage curves, elucidates that a low n-doped CdSeTe in the region near the MZO/CdSeTe interface caused the BHJ in the LSS and a loss of MZO doping and/or increase of the conduction band offset spike due to long-term stress caused the increased electric field near the MZO/CdSeTe interface at the DgS.

CdTe solar cell↗
DOE OSTI2021

Templated Growth and Passivation of Vertically Oriented Antimony Selenide Thin Films for High-Efficiency Solar Cells in Substrate Configuration

Antimony selenide (Sb 2 Se 3 ) is a promising low-cost photovoltaic material with a 1D crystal structure. The grain orientation and defect passivation play a critical role in determining the performance of polycrystalline Sb 2 Se 3 thin-film solar cells. In this work, a seed layer is introduced on a molybdenum (Mo) substrate to template the growth of a vertically oriented, columnar Sb 2 Se 3 absorber layer by closed space sublimation. By controlling the grain orientation and compactness of the Sb 2 Se 3 seeds, obtain high-quality Sb 2 Se 3 absorber layers with passive Sb 2 Se 3 /Mo interfaces is obtained, which in turn improve the transport of photoexcited charge carriers through the absorber layer and its interfaces. Post-deposition annealing of absorber layers in ambient air is further utilized to passivate the defects in Sb 2 Se 3 and enhance the quality of the front heterojunction. As a result of systematic processing optimization, Sb 2 Se 3 planar heterojunction solar cells are fabricated in substrate configuration with a champion power conversion efficiency of 8.5%.

14 SOLAR ENERGY↗
DOE OSTI2021

Metastable Dion-Jacobson 2D structure enables efficient and stable perovskite solar cells

The performance of three-dimensional (3D) organic-inorganic halide perovskite solar cells (PSCs) can be enhanced through surface treatment with 2D layered perovskites that have efficient charge transport. We maximized hole transport across the layers of a metastable Dion-Jacobson (DJ) 2D perovskite that tuned the orientational arrangements of asymmetric bulky organic molecules. The reduced energy barrier for hole transport increased out-of-plane transport rates by a factor of 4 to 5, and the power conversion efficiency (PCE) for the 2D PSC was 4.9%. With the metastable DJ 2D surface layer, the PCE of three common 3D PSCs was enhanced by approximately 12 to 16% and could reach approximately 24.7%. For a triple-cation–mixed-halide PSC, 90% of the initial PCE was retained after 1000 hours of 1-sun operation at ~40°C in nitrogen.

14 SOLAR ENERGY↗
DOE OSTI2021

Long-Term Degradation of Passivated Emitter and Rear Contact Silicon Solar Cell under Light and Heat

Advanced designs enable high-efficiency solar cells; however, more complex structures create new long-term stability concerns. Herein, the long-term degradation processes affecting advanced silicon solar cells using laboratory-based illumination and heating over hundreds of hours are investigated. The activation energy for the degradation of voltage is estimated and the degradation rates to normal solar cell operating temperature ranges are extrapolated. The cell degradation observed at high temperatures in the lab is kinetically similar to the process affecting field-deployed modules contributing to 0.37% year-1 of annualized degradation. Electroluminescence and photoluminescence mapping show that the degradation is dominated by minority carrier lifetime reduction. Suns-open-circuit voltage and light beam-induced current results indicate that the degradation could result from passivation degradation at the surface or defect formation in the near-subsurface region, leading to increased minority carrier recombination. This work highlights a long-term degradation process under elevated temperature and illumination that may continue to affect cells in an irreversible manner that is separate from recoverable light-induced degradation and light- and elevated temperature-induced degradation.

14 SOLAR ENERGY↗
DOE OSTI2021

Super Flexible Transparent Conducting Oxide-Free Organic–Inorganic Hybrid Perovskite Solar Cells with 19.01% Efficiency (Active Area=1 cm 2 )

Highly efficient organic-inorganic hybrid perovskite solar cells (OIHP-SCs) are often fabricated on a transparent conducting oxide (TCO) substrate such as indium tin oxide (ITO). However, the presence of TCOs is disadvantageous to the development of flexible OIHP-SCs due to the brittle nature of ITO which is easily breakable during bending. Herein, a flexible TCO-free OIHP-SC is demonstrated by using lithium bis(trifluoromethane)sulfonimide (Li-TFSI) as a codopant for the single-layer graphene transparent conducting electrode and poly(triarylamine) hole-transporting material (HTM) on a flexible polydimethylsiloxane substrate. The optical and electrical properties of the Li-TFSI-doped graphene substrate are measured by controlling the doping amount and the best conditions for charge extraction are established at a doping concentration of 20 mm Li-TFSI, thus optimizing the device photovoltaic performance. As a result, a highest power conversion efficiency of 19.01% is demonstrated by the flexible TCO-free OIHP-SC devices with an active area of 1 cm 2 . In addition, the flexible TCO-free OIHP-SCs exhibit good bending stability after 5000 bending cycles at radii of 6, 4, and 2 mm and excellent light soaking stability under 1 Sun light intensity over 1000 h as opposed to the poor stability when using poly(3,4-ethylenedioxythiophene) polystyrene sulfonate as the HTM.

14 SOLAR ENERGY↗
DOE OSTI2021

In-Operando Characterization of P-I-N Perovskite Solar Cell Under Reverse Bias

A solar module is often exposed to a variety of intensity and uniformity illumination conditions throughout a day. In the field, objects or dirt can block light from hitting the module creating a partial shading event. When a partial shading event occurs the module power point tracking system will typically push the shaded cells into reverse bias in order to avoid the current loss from the other series connected illuminated cells. When perovskite solar cells are operated in reverse bias, electrochemical reactions can occur, leading to both reversible and irreversible performance losses. Excess holes generated by reverse bias cause and push the oxidation reaction of halide ions from the lattice to neutral halogen interstitial. Small interstitial halogen atoms can diffuse across the device and potentially move from the perovskite layer and into the transport layers, shifting the fermi levels in the devices. In this investigation we utilize cross-sectional kelvin probe atomic force microscopy to map the band energetics of perovskite solar cells during reverse bias. We observe a 150 meV decrease in the work function of the C 60 . This leads to a decrease of 150 mV and 4 mA/cm 2 in V oc and in J sc respectively. Finally, we discuss methods to prevent this irreversible degradation after a perovskite device is held under reverse bias.

fullerene↗
DOE OSTI2021

Linking Transient Voltage to Spatially-Resolved Luminescence Imaging to Understand Reliability of Perovskite Photovoltaics

In this work, we present a methodology to separate effects of perovskite device metastability from irreversible degradation, using stress/rest cycling under constant current bias while collecting a series of electroluminescence images and continuously monitoring voltage. We develop a simulation model and procedures for image processing to better understand the effects of ion parameters on the transient nature of voltage and evolving electroluminescence images.

electroluminescence↗
DOE OSTI2021

Linking Transient Voltage to Spatially-Resolved Luminescence Imaging to Understand Reliability of Perovskite Photovoltaics: Preprint

In this work, we present a methodology to separate effects of perovskite device metastability from irreversible degradation, using stress/rest cycling under constant current bias while collecting a series of electroluminescence images and continuously monitoring voltage. We develop a simulation model and procedures for image processing to better understand the effects of ion parameters on the transient nature of voltage and evolving electroluminescence images.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2021

Chiral-induced spin selectivity enables a room-temperature spin light-emitting diode

In traditional optoelectronic approaches, control over spin, charge, and light requires the use of both electrical and magnetic fields. In a spin-polarized light-emitting diode (spin-LED), charges are injected, and circularly polarized light is emitted from spin-polarized carrier pairs. Typically, the injection of carriers occurs with the application of an electric field, whereas spin polarization can be achieved using an applied magnetic field or polarized ferromagnetic contacts. We used chiral-induced spin selectivity (CISS) to produce spin-polarized carriers and demonstrate a spin-LED that operates at room temperature without magnetic fields or ferromagnetic contacts. The CISS layer consists of oriented, self-assembled small chiral molecules within a layered organic-inorganic metal-halide hybrid semiconductor framework. The spin-LED achieves ±2.6% circularly polarized electroluminescence at room temperature.

77 NANOSCIENCE AND NANOTECHNOLOGY↗